This is a handle actuator for your dishwasher. It is made of black plastic, and is sold individually. The handle actuator is found in the control panel, and it releases the door latch when you lift the handle. If your current handle actuator is cracked or broken, you may not be able to open your dishwasher door, or the door will not close properly. The dishwasher also may not be able to start, and if this is the case, you will need to replace this part.
How Buying OEM Parts Can Save You Time and Money
Part Videos
Replacing your General Electric Dishwasher Door Handle Actuator
Troubleshooting
This part fixes the following symptoms:
Door latch failure | Will Not Start | Door won’t close
This part works with the following products:
Dishwasher.
Part# WD13X10045 replaces these:
AP4355961, 1469070, WD13X10008
Customer Reviews
Average Rating:
★★★★★
★★★★★
7 Reviews
4.6
Filter By Rating:
5 Stars
4
4 Stars
3
3 Stars
0
2 Stars
0
1 Star
0
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
★★★★★
★★★★★
John S - January 26, 2021
Verified Purchase
Just in case
The part was in great condition and came quickly. I replaced the old one even though the old one wasn’t broken, just in case, since I was in there replacing the electronics already
★★★★★
★★★★★
Ruth M - May 1, 2019
Verified Purchase
It worked!
We installed the Door Handle Actuator and the dishwasher works great!
Thank you.
★★★★★
★★★★★
Rob M - April 22, 2019
Verified Purchase
Door handle actuator
Part and video repair were perfect. Shipping was very slow (5+ days) even though it was shipped via FedEx.
★★★★★
★★★★★
Joseph J - September 10, 2018
Verified Purchase
Dishwasher handle replacement
I saved over $10.00 by ordering the part from PartSelect. The website video was very helpful for the installation. It made the whole process very easy.
★★★★★
★★★★★
Michael P - July 4, 2018
Verified Purchase
simple fix
Exactly what I needed.
★★★★★
★★★★★
Robert K - April 4, 2018
Verified Purchase
Part was perfect and repair easy with the help your video!!
Part was right and dishwasher working like new!! Thanks
★★★★★
★★★★★
Nathan S - February 6, 2018
Verified Purchase
Needs spring
Probably would’ve worked great if it came with the spring. So Don’t forget to order the spring of the one on your dishwasher is broken
< Prev
1
Next >
Customer Repair Stories
Average Repair Rating: 4.1 / 5.0, 17 reviews.
What's this?
Sort by:
< Prev
1
2
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
It makes a beeping sound in the middle of the dishwashing.
Remove the screws from the door and replace the switch interlock and door latch.
The problem is fixed and the dishwasher works fine so far (about three weeks) now.
The source of the problem looks more like the door latch because I use to push the door in to get it going before I replace the parts.
The v
... Read moreideo I received via email that show the how to do it was very helpful.
————- Update after more than month. (12/30/2020) The problem still persists. However I have a possible solution for it that doesn’t require any parts at all. The entire dishwasher is tilted backward. As the washing started and the water pileup in the bottoms of the dishwasher, it pull the entire dishwasher back work causing the switch interlock to release (open the relay causing the door open been sounds).
Level the dishwasher so that it doesn’t tilt backwards and this should fix the issue. I will post the latest after a month. If you need more info I can send a picture to describe the issue more clearly. ————————— Update 01-06-2021 The problem still persists. The above theory I had was wrong and didn’t make any difference.
However, I have a permanent solution but it may not be ideal for most people ??. The relay that get close/open when the door is close/open is now always CLOSED. To start the dishwasher just press start and make sure you don’t open the door while the dishwasher is running. It will not stop. I am sorry and I know it’s not a good solution but it’s kind of funny.
Dishwaher door not opening and Refrigerator air filter.
I followed instructions from the video link that was provided with the parts order confirmation.This repair was not difficult .
The refrigerator air filter was very easy to replace. There was also a new indicator (to remind me when to replace the filter again) that came with the filter.
Followed video and that part to install spring and door handle actuator was easy buy demo on video guy had hand in way where the outside door handle was inserted. I know what slot it went in but did not show how to insert in dishwasher. finally figured it out. But then led lights stopped working correctly so I need to buy some more parts
... Read morewhen I figured out what I need.
When we tried the door wouldn't open and the door handle actuator fell out in our hand
Took the screws out of the inner panel to open it and expose the latch area. Found the door spring stuck to the insulation so we saved it. Used the part's list picture to figure out how to put the latch parts together (wish the picture was better). Reattached the inner panel. The latch works better now than when it was new....which mak
... Read morees us wonder.
Parts were easy to find, easy to order and arrived prior to the advertised delivery date. Instructions for replacement were easy to understand and in about 10 minutes the old part was removed, and the new one installed. thanks for your prompt and efficient company.
ROY from CULPEPER, VA
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
0 of 2 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Door handle wouldn't work
After finally getting the door open and opening it up, the problem became apparent. Partselect helped me locate the part. it came quickly, and the repair was simple. It took me two trys to discover how the spring fit, but once I looked closely at the diagram, it was a cinch. I was a very proud dishwasher owner!
The repair was fairly simple. I unscrewed all of the screws holding the inside door panel from the outside door panel. I then removed the old (broken) door actuator with the new one, and then screwed everything back together. I used the exploded drawing of the dishwasher from the PartSelect website which helped considerably, and also don'
... Read moret forget to put the spring on the actuator before you install the new one. If your door actuator broke, then you should by the spring that attaches to it, because you have about a 1% chance of finding the new one.
When I first tried to fix the handle I could not figure out where the spring went. I went back online and looked at the diagram of the dishwasher on this site and learned where it went. Once I knew where every piece went it only took me about 5 minutes to put it back in and another 5 minutes to screw the cover back on. I am a newer hom
... Read moreeowner and want to be able to do minor fixes. This was my first one and was very happy that I was able to do it on my own.
Read less
Sally from Saint George, UT
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
15 of 20 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Door Latch Broke
This isn't a terribly tricky repair, and the parts are cheap so it's worth a try!
(I had one tricky thing which was the door actuator broke while the door was shut. So I had to get the machine out of it's space without being able to open the front of the machine. I did this by lowering the feet in the front of the machine and t
... Read morehen I used a hammer and flat chisel to break the two metal screws I had holding the top of the machine to the top of counter top...a little tricky!)
Remove screws from inside lower panel (where you put soap..the bottom) this will allow you to remove the inside of the door. But be careful as there are still wires attached so be careful to place the inside part without stressing the wires.
I needed to remove the metal harness and to open the black rectangular box that holds the interlock plunger so I could remove the plunger and spring (don't lose..and remember how it goes. take pictures if necessary). Then I was able to remove the broken actuator and see how it all fits together. It rests on top of the latch with notched side facing the inside of the machine. Make sure the notch is centered around where the interlock plunger is located.
Once you have the pieces fit together insert them into the door. Replace the plunger and spring and close the black rectangular box. Then replace the metal harness.
Hold everything in place and put the inside of the door back into position and lock it down with the screws.
You can test the door to make sure it's working but the whole mechanism is less functional when the machine isn't secured into its space. So, if you're mostly sure you've got it right, resecure the machine into its space making sure it's solid and then you should be good.
Like most everyone here I was very happy to accomplish this repair without calling in the repair service!! Awesome.
Read less
Erik from New York, NY
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Screw drivers, Wrench (Adjustable)
7 of 10 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
dishwasher door would not latch
opened door removed screws holding back side of door took out front panel with latch assembley found broken part and replaced it
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
5 questions answered by our experts.
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Deidra
April 23, 2019
My dishwasher will no longer shut. The repectle on the back of the door for the latch wont allow the latch to enter. Is this the correct part to replace in this case?
For model number GLD4408R10WW
Hi Deidra, thank you for your question. If that is the part that is broken on your door latch then yes. You should be able to see which piece is broken as these are physical parts for the most part and not electrical. If you are not sure I would suggest just taking a deeper look at the parts to see if you notice any damage to be sure. I hope that helps. Good luck with your repair.
2 people found this helpful.
Was this helpful?
Thank you for voting!
Tyrone
May 8, 2019
Why is my dishwasher staying on rise only mode
For model number GLD5600VV00BB
Hello Tyrone, thank you for contacting us. Try unplugging the dishwasher or turning the breaker off for 60 seconds to reset the machine. If this does not solve the problem, you will need to replace the touch pad which is sold on the Escutcheon Assembly part PS2370581. We hope this helps.
1 person found this helpful.
Was this helpful?
Thank you for voting!
Lucy
May 14, 2019
My GE profile quietpower 4 latch is wobbly in its place and will not allow the door to dishwasher to be opened. I don't have any space between top of dishwasher and bottom of countertop so i cannot even jiggle a thin and long allen wrench in the space. I was try to see if i snap the latch through the underside of latch, but that doesn't work either. I cannot seem to pull the dishwasher either. Help?!
For model number PDW7880N10SS
Hello Lucy, thank you for your question. To access that area you should open the door and unscrew the mounting plates from the counter top and pull the dishwasher out of its space a bit to access the latch area. You will want to check the Door Handle Actuator Part #: PS2337860, Retainer Handle - Black Part #: PS958991, Recess Door Spring Part #: PS285013, and latch handle Part #: PS259297. I hope this helps!
1 person found this helpful.
Was this helpful?
Thank you for voting!
Min-Lee
August 29, 2019
Hi, our dishwasher can be closed, but can not be opened normally. While it is close, we can't press start either.We have now select "spring plunger", "door handle actuator", "switch interlock assembly" as possible part broken.
how can we test and determine which part should we change?
thanks!
For model number GDWF160R10SS
Hello Min-Lee, thank you for inquiring. You can test the Interlock Switch Assembly, part number PS783632 for your model, with a multi-meter for continuity. With the switch pressed down, it should test as 0 ohms of resistance to have continuity. Otherwise it is faulty and will need to be replaced. Good luck with your repair!
1 person found this helpful.
Was this helpful?
Thank you for voting!
Marie Noonan
September 9, 2017
Door will not open after cleaning. How do i open it? Latch seems broken.
For model number PDW7300N10WW
Hi Marie,
Thank you for your inquiry. It sounds like you have to replace the the door latch. To open the door you may have to unplug the dishwasher for a few minutes and plug it back in to see if that will allow the door to open. If you have any issues you will need to consult your owners manual. I hope this helps. Thank you and have a great day!
