Jenn-Air Cooktop Igniters

Videos!

Your Price

$41.20

Jenn-Air Cooktop Top Burner Igniter

★★★★★

20 Reviews

PartSelect Number PS2082000

Manufacturer Part Number 74004053

This is a surface burner igniter, also known as a top burner ignitor and stove top spark electrode. It is used to generate the spark that lights the surface burner. If your stove will not start, element does not heat, or gas igniter glows but does not light, replacing the igniter can solve these issues. For this installation, you will need a Phillips screwdriver and needle nose pliers. First place the grate on top of the burner, then lift the burner and disconnect the wires. Next remove the two Phillips screws from the bottom of burner, pull igniter out of the burner and wiggle in the new one. Refer to the installation instructions provided by the manufacturer for more instructions.

Fixes these symptoms

Element will not heat
Gas igniter glows, but will not light
Will Not Start
See more...

Installation Instructions

roy from East Providence, RI

gas burner ignitor failure

Lift out sealed burner assembly rear of stove first while careully sliding to rear to disengage ignitor probes.Remove philips head screws from bottom sheet metal housing to expose bottom of burners Remove gas tube assembly screws and move tube away carefully.Unplug wires from ignitor.Remove screws for ignitor .Remove ignitor, I noticed that rust and dirt had built up around burner to pan connection.I used my oil filter wrench to turn slightly the burner to remove it from the pan to clean.Reassembled in reverse order. Read more...

Your Price

$41.65

Jenn-Air Cooktop Burner Electrode

★★★★★

12 Reviews

PartSelect Number PS11744318

Manufacturer Part Number WP74009336

This is a burner electrode for your oven, range, or stove. This part has a male spade. It helps your burner ignite by creating a spark, producing a flame, and lighting the surface burner. If your burner will not heat properly, you may have to replace the burner electrode. Your electrode is located under your burner. This is an OEM replacement part that will be sourced from the genuine manufacturer. This part measures less than 1.5 inches long. It is sold individually. If you need a wire lead to complete your repair, you can purchase them locally.

Fixes these symptoms

Element will not heat
Gas igniter glows, but will not light
Will Not Start
See more...

Installation Instructions

Dennis from Iredell, TX

Simple to change, but you do need a torx bit screwdriver.

Remove screws holding burner down, invert and remove screw in igniter. Reverse to reinstall. Read more...

Your Price

$25.40

Jenn-Air Cooktop Surface Burner Spark Igniter

★★★★★

8 Reviews

PartSelect Number PS11746068

Manufacturer Part Number WP8523793

This part helps your burner ignite and produce flame.

Fixes these symptoms

Element will not heat
Gas igniter glows, but will not light
Will Not Start
See more...

Installation Instructions

Daniel from Needham, MA

spark igniter was weak and not lighting the flame.

Open top oven door and remove the 2 front screws which hold the burners and controls to the frame. DO NOT lift the burners more than an inch or so to look inside. You WILL bend the gas lines in the back if you do. Pull out stove from the wall, shut off gas supply and disconnect hose if needed to have room to work. Remove top back panel and remove the 3 wires connecting the top burner assembly and also remove the 2 gas lines. Now you will be able to remove the burner assembly safely. Flip it over and try to unscrew the screw holding the igniter. When you fail, drill it out and get a small metal screw to replace it. The metal is soft and the screw is hard, so drill carefully. The rest is easy, put in the new igniter and screw. and put it back together. Read more...

Your Price

$86.71

Jenn-Air Cooktop Spark Igniter Set

★★★★★

5 Reviews

PartSelect Number PS11744110

Manufacturer Part Number WP74005890

This part provides the spark to the burners.

Fixes these symptoms

Gas igniter glows, but will not light
Will Not Start
See more...

Installation Instructions

Patricia from Overland park, KS

Spark igniter out

The primary spark igniters failed. Take the (small) screws out of the sides and bottom of the pan. The front of the pan must be removed from the bottom, because the front burner igniter wire is too short to allow reassembly once attached. Only other is the screws for the attachment bracket are larger than the holes. Suggest routing them out slightly to get them to grip the screws. Otherwise it is quite simple. Pull the connections with a needlenose and press the new wire connection back on firmly. Screw the screws back in the pan. Read more...

Your Price

$61.88

Jenn-Air Cooktop Spark Module - Surface Burners

★★★★★

11 Reviews

PartSelect Number PS2003170

Manufacturer Part Number 12001596

This part may differ in appearance, but functions same as original part. : This part sends enough current to the igniter to create a spark to the bottom of the burner cap.

Fixes these symptoms

Element will not heat
Gas igniter glows, but will not light
Will Not Start
See more...

Installation Instructions

jonathan from Bryson City, NC

No spark at top burners, first one then eventually all 4.

Most of the repair time was spent researching the problem online, locating the spark module inside the range, and selecting the part online. Installation was easy. Key troubleshooting info for me was, if there is no clicking, the spark unit is probably worn-out. I traced the ignition wires from the burners down to the spark module, located inside a 2x3" metal housing next to the bottom drawer. I removed 2 screws and out it came. The replacement unit pictured on the PartSelect site was not identical to the original but had the same number of contacts. I ordered the part and it arrived a few days later. The old connectors slipped easily onto the new pins, and I screwed the new unit into the range using the new metal housing. All 4 burners now spark up quickly, and we saved at least $100 on a service call. It was well worth the time and effort -- thanks! Read more...

Your Price

$24.47

Jenn-Air Cooktop Surface Igniter

PartSelect Number PS11727815

Manufacturer Part Number W10833887

Installation Instructions

Ronald from ROSEVILLE, CA

Surface ignitor not working on one burner

Disconnect power and turn off gas. Remove all grills, knobs and burners. Under the burners are 2 Phillips head screws. Remove all 10 screws. Remove surface plate. Remove the one igniter with problem. There is a small metal clip holding it in place. Remove the wire. Install new ignitor and reverse all steps above. Read more...

Your Price

$25.78

Jenn-Air Cooktop Igniter-SURF

★★★★★

1 Review

PartSelect Number PS11731309

Manufacturer Part Number W10854967

Your Price

$79.47

Jenn-Air Cooktop E-Burner Igniter

★★★★★

1 Review

PartSelect Number PS11744119

Manufacturer Part Number WP74006072

Fixes these symptoms

Will Not Start
See more...

Installation Instructions

Steven from SOUTH EASTON, MA

Grill Ignitor needed to be replaced : order # 20418333

Still not fixed. Waited about a year for the part to arrive, due to "COVID supply chain issue". Part finally arrived and was missing a sub component (ironically the worn out part). Now awaiting a reorder confirmation that this is being sent along with a return mailing label.
The re-order required me to obtain a better picture of the part from your competitor's web site, to prove the part sent was defective as your site was inadequate. My first call on this issue failed because of an absence of the better picture.
The 2nd call to customer service was very understanding and professional but I have yet to receive any confirmation on this re-order in the past 5 days. Read more...

Your Price

$164.03

Jenn-Air Cooktop Top Burner Spark Igniter

PartSelect Number PS11743872

Manufacturer Part Number WP71002179

This spark igniter electrode has a 35" wire lead.

Fixes these symptoms

Gas igniter glows, but will not light
Will Not Start
See more...

Installation Instructions

Steve from Sedona, AZ

Igniter not sparking and display panel dim

i'm writing this several days after installling parts and from memory so forgive me if i miss a step or get the # of screws wrong.

Clock assembly replacement was very easy. Open oven door and remove screws just below the display panel, remove burner knobs and remove the 2 screws hidden by the knobs, remove the 2 screws holding the side triangular pieces (1 screw for each side). you may need to pull range out and away from the counter to remove the triangle pieces. remove the display panel, flip it over and remove 2 screws holding clock assembly. gentle remove the ribbon cables from the old assembly and then perform everything in reverse to reassemble.

Replacing the igniters was more difficult and took up the bulk of the time. Warning: find some way to test the spark module first. I replaced both igniters (1 wire was broken so it needed replacement for sure, but the other igniter may have been good...) and they still do not work. I'm waiting on delivery of a spark module.

remove all burner stuff (grill, burner assembly, etc.), then remove the top of the stove, there are 2 screws on each side and several in the back, there are also screws around the inside rim of the burner pans. also remove the panel on the back of the stove, this allows access to the spark module. gently lift the burner pans, reach underneath the pan and unscrew the nut holding the igniter in place. fortunately mine were easy to unscrew and i could do it with my fingers, getting a wrench underneath would have been a challenge. unhook the igniter wire from the spark module and remove the old igniter. install new igniter in reverse and reassemble. Read more...