Hedge Trimmer Parts

Popular Hedge Trimmer Parts

Your Price
$4.99
   In Stock
Hedge Trimmer TERMINAL, XRU11
PartSelect Number PS16390378
Manufacturer Part Number 644809-6
Your Price
$6.59
   In Stock
Hedge Trimmer Primer
★★★★★
★★★★★
3 Reviews
PartSelect Number PS11826485
Manufacturer Part Number P005003120
This Primer Bulb is a clear, plastic, individually sold part with an Outer Diameter of 0.720 inches (18.30 mm) and a Height of 0.674 inches (17.12 mm). With Flange: 0.842" (21.40 mm). This part is rated as Easy to install by customers, and attaches to the primer pump assembly. If the part shows signs of breakage, such as cracks appearing due to the bulb drying out, or fatigue, then it must be replaced. Refer to your owners manual/model number to ensure you are choosing the correct part.
Fixes these symptoms
Your Price
$5.36
   In Stock
Hedge Trimmer Fuel Filter
★★★★★
★★★★★
2 Reviews
PartSelect Number PS11826311
Manufacturer Part Number A369000480
This OEM Fuel Filter is a silver and white, steel/felt, part measuring about 1.25 inches in length and 3/4 inch wide. It can be installed with pliers and is rated as Easy to install by customers. This part attaches inside the fuel tank to clean the fuel of debris, and should be replaced during regular maintenance, check your manual for recommended replacement time. If the filter is leaking or it has a blockage preventing fuel flow, then it should be replaced. If the engine sounds like it is not getting enough fuel, then remove the filter and check it for blockage.
Installation Instructions
Paul from SENECA, SC
Fuel line grommet rotted
This blower is quite old looked on YouTube. Removed grommet with needle nose pliers. Removed tank to install new parts. I had trouble getting return line off carb so planned to reuse it after grommet was in place. Thin was a mistake because the seated grommet compresses the holes. Took unnecessary time to get it through. With my trimmer with all lines in place. Hardest part was to get the grommet to seat even with silicone. Read more...
Your Price
$4.99
   In Stock
Hedge Trimmer Fuel Line Grommet
★★★★★
★★★★★
7 Reviews
PartSelect Number PS8859978
Manufacturer Part Number 13211546730
This fuel line grommet is compatible with several types of outdoor power equipment. The fuel line grommet creates a seal where the fuel line enters and exits the fuel tank. It is made of black rubber and this version has 3 holes. If your fuel tank or fuel lines are leaking fuel, or your current fuel grommet is worn out, you should consider replacing it. This item is sold individually.
Installation Instructions
Donald from ORANGE PARK, FL
fuel tank leaking around where lines went in tank
took all the old parts off and replaced them Read more...
Your Price
$4.98
   In Stock
Hedge Trimmer Primer Pump
PartSelect Number PS8858167
Manufacturer Part Number 12318140630
The Primer Pump, aka the Pump Bulb, is a clear, individually sold, plastic part, sourced from the original equipment manufacturer. It has an Outer Diameter of 0.616 Inches, 15.66mm and is 0.558 Inches and 14.19mm in height. This part is used to pump fuel from the tank to the carburator and is rated Easy to install. This part installs onto the primer assembly. If the part dries out or starts leaking that means it is broken (likely due to fatigue or general wear) and must be replaced. Check the model number to ensure you are choosing the right part.
Your Price
$3.99
   In Stock
Hedge Trimmer Spark Plug Bpm-8Y
★★★★★
★★★★★
1 Review
PartSelect Number PS9263506
Manufacturer Part Number 15901019830
This Spark Plug Bpm-8y is a silver and white OEM part. Made of steel and ceramic it is individually sold, and is an electrical part. It is installed with a spark plug socket and is rated as Easy to install. It is attached inside of the cylinder head, and is used to ignite the air fuel mixture inside the combustion chamber. You can clean the spark plug with a fine sandpaper of 180 or more, then spray it with carburator cleaner and wipe dry. However, even after regular maintenance, spark plugs need to be changed as part of good engine fine-tuning. Regap to manufacturer specifications. Refer to your owners manual or model number to ensure you are choosing the correct product. Note: If your engine has more than one cylinder and sounds like it has a miss, you can remove each spark plug wire one at a time to find the miss. If the engine drops in rpm when you remove the wire, then that cylinder is fine, if it does not drop then you have found your miss!
Your Price
$7.46
   In Stock
Hedge Trimmer Fuel Line (25" Length)
PartSelect Number PS9472350
Manufacturer Part Number 530069599
This Fuel Line is a 25-inch, clear, plastic line used to deliver fuel. It requires a screwdriver, pliers, socket set, and nut driver and is rated as "Easy" to install by customers. If the fuel line wear out to the point of breaking, cracks and/or leaking will appear and the part should be replaced. Refer to your make, model and diagram to ensure this is the correct part for you.
Your Price
$7.09
   In Stock
Hedge Trimmer Air Filter
★★★★★
★★★★★
7 Reviews
PartSelect Number PS9195232
Manufacturer Part Number A226001410
This part is the replacement air filter for your small engine, used for outdoor power equipment. It has a black plastic rim that is approximately 2.5 inches by 2.5 inches. The air filter in your small engine prevents dirt and debris from entering the cylinder, where it can cause more serious damage. If your air filter is clogged, it can decrease your engine performance, and it will need to be cleaned or replaced. If the filter is damaged, it will need to be replaced as well. This is an OEM part sourced directly from the manufacturer, and is it sold individually.
Installation Instructions
Paul from SENECA, SC
Fuel line grommet rotted
This blower is quite old looked on YouTube. Removed grommet with needle nose pliers. Removed tank to install new parts. I had trouble getting return line off carb so planned to reuse it after grommet was in place. Thin was a mistake because the seated grommet compresses the holes. Took unnecessary time to get it through. With my trimmer with all lines in place. Hardest part was to get the grommet to seat even with silicone. Read more...
Your Price
$4.99
   In Stock
Hedge Trimmer Fuel Line Fitting
★★★★★
★★★★★
1 Review
PartSelect Number PS9469715
Manufacturer Part Number 530023877
The Fuel Line Fitting is a plastic part which attaches two pieces of fuel line together. If broken due to damage/fatigue, there may be a leak and the part must be replaced. Installation is rated as "Easy". Refer to your make, model and diagram to ensure this part is correct for you.
Fixes these symptoms
Installation Instructions
Mark from LYNDONVILLE, NY
Deterioration of fuel line system
Removed the top cover (T25 torx), and side cover (T25 torx) with recoil starter. Drained all fuel, and removed all pieces of fuel old fuel line and the weighted filter from inside the tank by shaking out and the (long forceps). A spot headlamp makes it easier to see inside the tank for much of the procedure. Remove the foam filter to find the two 8mm nuts and remove the air filter housing and carburetor (nut driver, 8mm socket) the choke lever slides out of its slot with some wiggling and moving the carb back off the mounting studs. Leave the throttle cable attached to the filter housing and move both assemblies out of the way to access the top wall of the fuel tank. There is a cover over the carb adjust screws that wiggles out also. The fuel line and purge line both pass through the wall of the tank and need to be pulled out with some effort (long curved forceps) from inside the tank through the fuel fill port. They are a tight fit. Pay attention to the lines size and location. Large line is in the position away from the recoil starter with the little plastic fitting hanging near the top of the tank. The smaller line is closest to the recoil starter. Both new lines will need to pass through the tank wall (this is the most difficult part). To facilitate the initial entry through the wall of the tank, cut a tapered end on your new lines. Use a very slippery lube to coat the end of the line and push it into the tank as far as you can from the top (forceps or soft grip pliers) help. Look inside the tank and pull the lines through fully out of the tank fill (long curved forceps and head spot light). Don't pull all the way through the fuel fill, just enough to install the new fuel line fitting in the return purge line and the new weighted filter on the fuel line and pull the lines back inside the tank. The return line with fitting close to the top of the tank and the filter hanging so it lays at the bottom of the tank, and able to swing around so it keeps contact with fuel at all times. Remove the old purge/primer bulb two screws (Phillips). The short stem is suction, long stem is pressure. Don't mix them up and connect lines backwards, don't ask me how I know! Lol! If you have such a saw like mine, that has no fuel lines intact, it is difficult to vision the line routes. There are helpful schematics on the internet. Just remember that the purge bulb long fuel stem sends pressure back to the tank through the return line (larger line in the tank with the line fitting away from the recoil). That line can now be cut to length and pushed on the bulb long stem. The suction side of the bulb short stem, connects to the purge line on the side of the carburetor (short line). You need to cut that line to the same length as the old one. It has to curve twice to get to the suction side of the purge bulb without kinking. The only other line left is the fuel line with the filter attached hanging inside the tank. Be sure you have the filter able to lay on the floor of the tank and move around. That line connects to the carburetor opposit side from the purge bulb. Dont cut that one until the carb is installed for proper length. The fuel routes from that filtered line into the carb, then out of the carb to the purge bulb suction side, then out to the return line in the tank with the fitting end. That fitting installed into the line serves only to keep the line from pulling back out of the tank, nothing attaches to it. Make sure all lines are clear of the mounting area of the carb, and throttle function. Pass the bulb lines through the slot in the side of the case being sure the lines don't kink. Secure the bulb with the two phillips screws. Position the carb on the studs and slide the choke lever into its place in the case as you go. Place the filter housing on the studs and push the carb and housing down watching the fuel lines for any kinks, especially where the throttle cable is in close proximity to the short carb purge line. Check the throttle function for interferance, and Install the two 8mm nuts. Now route the fuel line around the throttle mechanism out of the way, hold it to the barb on the side of the carb and cut it to length and install. Put some fuel mix in the tank (dont fill it) to test. Press the primer bulb, tilting the saw with fill cap removed, and see if anything leaks, also watch fuel flow back to the tank inside as you press the bulb. You should see fuel and air bubbles from the purge line. When all air bubbles are gone the system is purged. Install the new foam filter in the housing and then the top and side cases. I did not reinstall the cover of the carb adjust needle screws so I could adjust the fuel/ air mixture to run at peak performance. Hope this helps! The kit that I got was perfect and there are some useful instructions included. Thank you! Respectfully Mark Read more...
Your Price
$8.60
   Special Order
Hedge Trimmer Filter, Fuel
★★★★★
★★★★★
2 Reviews
PartSelect Number PS11826309
Manufacturer Part Number A369000460
The Fuel Filter is a white and silver, individually sold, steel part. It reuires pliers to install and its installation is rated as Easy. The part attaches inside of the fuel tank and is used to clean the fuel of debris. It should be changed regularly. Check your owners manual for the recommended replacement schedule for your engine. If the fuel is leaking or their is a blockage, you will know the part is broken and will likely need to be replaced. To check for small leaks, feel around for dampness and the smell of fuel.
Installation Instructions
Keith from NORWOOD, NJ
Replace clogged fuel filter.
Thru fuel cap, insert copper wire with hook formed on end. Fish around until you grab the fuel line. Pull the fuel line and filter thru the fuel fill neck.
Pull off old filter and replace with new. Push back into fuel tank & be done.
Read more...

Hedge Trimmer Brands

Related Hedge Trimmer Parts

Popular Hedge Trimmer Models

Below are the most popular Hedge Trimmer models we have. Enter your model number in the search box to find your model.