Genuine OEM Pole Saw Parts

Your Price

$4.99

Pole Saw Oil Cap

PartSelect Number PS9873442

Manufacturer Part Number 099988002015

Your Price

$22.61

Pole Saw Boom Assembly

PartSelect Number PS9939666

Manufacturer Part Number 311075001

Your Price

$6.59

Pole Saw Primer

★★★★★

3 Reviews

PartSelect Number PS11826485

Manufacturer Part Number P005003120

This Primer Bulb is a clear, plastic, individually sold part with an Outer Diameter of 0.720 inches (18.30 mm) and a Height of 0.674 inches (17.12 mm). With Flange: 0.842" (21.40 mm). This part is rated as Easy to install by customers, and attaches to the primer pump assembly. If the part shows signs of breakage, such as cracks appearing due to the bulb drying out, or fatigue, then it must be replaced. Refer to your owners manual/model number to ensure you are choosing the correct part.

Fixes these symptoms

Will Not Start
See more...

Guide Bar Assembly – Part Number: 099629001001

Your Price

$16.05

Pole Saw Guide Bar Assembly

★★★★★

3 Reviews

PartSelect Number PS9872907

Manufacturer Part Number 099629001001

Fixes these symptoms

Chain comes off guide bar
See more...

Extended Boom Assembly – Part Number: 311081002

Your Price

$24.59

Pole Saw Extended Boom Assembly

PartSelect Number PS9939669

Manufacturer Part Number 311081002

Spark Plug Bpm-8Y – Part Number: 15901019830

Your Price

$3.99

Pole Saw Spark Plug Bpm-8Y

★★★★★

1 Review

PartSelect Number PS9263506

Manufacturer Part Number 15901019830

This Spark Plug Bpm-8y is a silver and white OEM part. Made of steel and ceramic it is individually sold, and is an electrical part. It is installed with a spark plug socket and is rated as Easy to install. It is attached inside of the cylinder head, and is used to ignite the air fuel mixture inside the combustion chamber. You can clean the spark plug with a fine sandpaper of 180 or more, then spray it with carburator cleaner and wipe dry. However, even after regular maintenance, spark plugs need to be changed as part of good engine fine-tuning. Regap to manufacturer specifications. Refer to your owners manual or model number to ensure you are choosing the correct product. Note: If your engine has more than one cylinder and sounds like it has a miss, you can remove each spark plug wire one at a time to find the miss. If the engine drops in rpm when you remove the wire, then that cylinder is fine, if it does not drop then you have found your miss!

Your Price

$7.09

Pole Saw Air Filter

★★★★★

7 Reviews

PartSelect Number PS9195232

Manufacturer Part Number A226001410

This part is the replacement air filter for your small engine, used for outdoor power equipment. It has a black plastic rim that is approximately 2.5 inches by 2.5 inches. The air filter in your small engine prevents dirt and debris from entering the cylinder, where it can cause more serious damage. If your air filter is clogged, it can decrease your engine performance, and it will need to be cleaned or replaced. If the filter is damaged, it will need to be replaced as well. This is an OEM part sourced directly from the manufacturer, and is it sold individually.

Installation Instructions

Paul from SENECA, SC

Fuel line grommet rotted

This blower is quite old looked on YouTube. Removed grommet with needle nose pliers. Removed tank to install new parts. I had trouble getting return line off carb so planned to reuse it after grommet was in place. Thin was a mistake because the seated grommet compresses the holes. Took unnecessary time to get it through. With my trimmer with all lines in place. Hardest part was to get the grommet to seat even with silicone. Read more...

Your Price

$4.99

Pole Saw Primer Pump

PartSelect Number PS8858167

Manufacturer Part Number 12318140630

The Primer Pump, aka the Pump Bulb, is a clear, individually sold, plastic part, sourced from the original equipment manufacturer. It has an Outer Diameter of 0.616 Inches, 15.66mm and is 0.558 Inches and 14.19mm in height. This part is used to pump fuel from the tank to the carburator and is rated Easy to install. This part installs onto the primer assembly. If the part dries out or starts leaking that means it is broken (likely due to fatigue or general wear) and must be replaced. Check the model number to ensure you are choosing the right part.

Bulb-Purge "snap-in" – Part Number: 530047721

Your Price

$6.21

Pole Saw Bulb-Purge "snap-in"

PartSelect Number PS9471212

Manufacturer Part Number 530047721

This primer bulb, also known as a purge bulb, is used to push more fuel from the fuel tank into the carburetor of your small engine equipment, to help the engine start easier. Over time and through extended use and exposure to gas and oil, the bulb of the primer will eventually lose its elasticity and crack or break. This bulb is made of plastic and can be replaced by accessing the ignition system. Disconnect the fuel lines and pop out the bulb with a set of pliers, and once you pop in the new bulb, you just reconnect the fuel lines. This bulb is compatible with a variety of makes and models of small engine equipment and is sold as an individual part.

Installation Instructions

Robert from MANVILLE, NJ

Replace the fuel lines

Replaced all fuel lines. Followed instructions found on Partselect.com, which said to insert cut fuel line in tank and use forceps to reach back in the tank and pull the fuel line through. The problem was that I did not have forceps, or needle nosed pliers that could reach the end of the hose.

Instead of running the line into the tank, I found another suggestion online to run the line from inside the tank outward, allowing me to grab the line with any pliers and thread it. The way I did this was used about a foot length of 14 gauge copper wire. Put an inch or two into the hose (that has been cut on an angle), and use a little black tape to secure the hose on the wire. Now you should be able to route the stiff wire from inside the tank to the fuel hole in the tank. Fish the wire through, and it should be enough to get the tapered end through the tank. Pull the copper wire, mine came out, but there was enough of the hose exposed on the outside of the tank for me to grab with pliers and pull it through. Read more...