Washer Parts

Popular Washer Parts

Your Price
$74.04
   In Stock
Washer Washing Machine Drain Pump
★★★★★
★★★★★
269 Reviews
PartSelect Number PS3579318
Manufacturer Part Number 4681EA2001T
The drain pump and motor assembly may also be known as the washer drain pump and is a part for your washer. The drain pump helps expel water from the washing machine. The drain pump is activated after the spin cycle speed is maintained for a specific period of time. To make this installation you will need a Phillips screwdriver, a small flat-blade screwdriver, a pair of needle-nose pliers, and a pair of slip-joint pliers. Note that the pump casing is not included. This medium-difficulty repair may vary, but can generally be started by disconnecting power, then removing the top of the washer by taking out the four back screws and two small brackets. Then, remove the front panel by taking out the two screws and eight tabs that should be taken from the top. Moving down the front of the washer, remove the door, latch, tub gasket, and drain cover. Disconnect the drain hoses and clip from under the drain assembly, and install new assembly from there. Reassemble parts in direct reverse order -- taking photos during disassembly and keeping parts clearly organized can help here. Despite the number of steps, you will only need a standard Phillips screwdriver to complete this repair.
Fixes these symptoms
  • Draining Issues
  • Engine runs but does not pump water
  • Leaking
  • See more...
Installation Instructions
Jorge from Apple Valley, CA
Washing maching wouldn't drain
Removed the top of the washer by removing the 4 back screws and 2 small brackets. Then I removed the front panel, this was actually the hardest part, 2 screws and 8 tabs that you pop out carefully from the top of the panel. I only disconnected the power button and was able to rest the panel on top of the washer. The rest of the washer came apart quickly just moving down the front of the washer and removing the door, latch, tub gasket, drain cover. Removing the pump was just a mater of disconnecting the drain hoses, and one clip under the drain assembly. 3 screws attach the drain to assembly to the pump and only 2 wires that are clearly marked. Reassembly is just going back through in reverse order of disassenbly. The best thing about this is that it all comes apart with a standard phillips screwdriver. Read more...
Your Price
$4.39
   In Stock
Washer Agitator Directional Cogs
★★★★★
★★★★★
358 Reviews
PartSelect Number PS388034
Manufacturer Part Number 80040
This kit is used for replacing the agitator directional cogs (Agitator Dogs, Agitator Repair Kit, Washer Agitator Dogs, Agitator Dog Ears). The agitator is what creates the thrusting motion in your washer to tumble your clothes during the washer cycle. Your agitator will rotate one way, and not the other. The agitator dogs are what prevent the agitator from rotating in both directions, while allowing it to rotate in one direction. Your agitator cogs may be malfunctioning if you can manually rotate the agitator in both directions. If broken they will need to be replaced. Cogs can be found by simply removing the softener dispenser and then removing the agitator cap. The are attached to the agitator. This replacement part features 4 agitator directional cogs. There are 4 cogs per package that are made up of high-quality plastic. This part comes in white/beige.
Fixes these symptoms
  • Does not dispense fabric softener or detergent
  • Marks left on clothes
  • Not cleaning dishes properly
  • See more...
Installation Instructions
mike from Kent, WA
washer wouldn't agitate
First pry off the cap of the agitator. Then using a socket remove the bolt that holds the plastic cup in place. Remove this cup by prying it loose from the two tabs that hold it in place. Once this cup is removed you can get to the broken cogs.
Slip the new cogs into the underside of the cup, and slide the cup back down in the agitator housing using the slots on the side for a guide. (You may want to remove the entire agitator and assemble everything upside down, then flip it all back over to mount, so the cogs don't fall out).
Tighten the bolt, snap the cap back in place on top of the agitator and your'e done. Easy repair.
Read more...
Your Price
$12.92
   In Stock
Washer DOOR STRIKE
★★★★★
★★★★★
14 Reviews
PartSelect Number PS16218028
Manufacturer Part Number W11457841
This door strike is an authentic OEM replacement part that is compatible with various models of top-load washing machines. The door strike is located along the door frame, where it engages with the latch when the door is closed. It keeps the door securely shut so that the washer can start and prevents it from swinging open while the washer is running. It is a safety mechanism that prevents water leakage, injuries, and damage to the washer. If the door strike is damaged or worn down, it may be unable to lock the door properly and the washer may stop mid-cycle or fail to start altogether. Replace the door strike promptly to ensure the proper functioning of your washer.
Fixes these symptoms
  • Lid or door won’t close
  • Locking Issues
  • Will Not Start
  • See more...
Installation Instructions
John from AURORA, CO
Tab on door strike got broken off and washer would not operate without it.
Pushed in on door strike and rotated it counterclockwise, removed broken strike and installed new strike. NOTE: when removing the old strike (turning counterclockwise) it felt like it might break and/or was attached with an screw that I didn't see but it came right out. Read more...
Your Price
$8.00
   In Stock
Washer Suspension Spring
★★★★★
★★★★★
27 Reviews
PartSelect Number PS11743345
Manufacturer Part Number WP63907
The suspension spring supports the outer tub and keeps the tub steady during loads that could cause an unbalance. If this part breaks, is worn down or has stretched out and lost its spring, it could cause the load to be off-balance which can lead to excessive shaking, moving, noise, and leaks. For this repair, you will need a 1/4 nut driver, a putty knife, a flat blade screwdriver, and a pair of needle-nose pliers. Disconnect the power supply, fill hoses, and drain hose to give you safe and easy access (have a container nearby for water left in drain hose). This item is sold individually, which is important as you may need to repair multiple springs in your appliance, which carries three suspension springs. As an inexpensive part, we recommend purchasing several at a time, as they can be very useful to have on-hand.
Fixes these symptoms
  • Leaking
  • Shaking and Moving
  • Spinning Issues
  • See more...
Installation Instructions
Brian from Seattle, WA
Washer tub slammed into washer body during spin cycle
If you load a washing machine unevenly, it will spin out of balance. But our washer seemed to make noise during the spin cycle regardless of how the load was distributed. I suspected that the suspension or balancing springs were getting tired, and ordered a replacement set.

First I disconnected the washer from the water and power supply, then I laid it on its back.

The tub rested on the back of the washer, making two of the three suspension springs relax, and they were pretty easy to pull out with pliers. After the first two were out, I had to support the tub with a couple 2x4s to relax the third suspension spring.

Installation was the reverse of removal - install the lower suspension spring, remove the 2x4s, then install the two other suspension springs.

The tub balancing spring was easy to replace, and probably wasn't the cause of the problem.

With $25 in parts and about 15 minutes, my washer spins much more quietly.
Read more...
Your Price
$22.33
   In Stock
Washer CLUTCH
★★★★★
★★★★★
1 Review
PartSelect Number PS11729473
Manufacturer Part Number WH05X24185
This is a clutch for your washing machine. The clutch is made of a white plastic material and is used within washing machines to engage and disengage the transmission during the wash and spin cycles, and ultimately help spin the basket of the tub so your clothes finish damp and not soaked. If your washer has issues with spinning or agitating, this part is likely broken or has worn out, and will need to be replaced. To replace this part, some disassembly of your washer will be required, and tools like a screwdriver and socket wrench will be needed. This clutch is sold as an individual and does not come with any other parts.
Fixes these symptoms
  • Noisy and Marks Left on Clothes
  • Spinning Issues
  • Will not agitate
  • See more...
Installation Instructions
Marvin from SHOSHONE, ID
Washer not spinning
Tilt washer back.
Remove belt gaurd.
Remove belt.
Remove pulley.
Remove clutch and shifter.
Install in reverse order
Read more...
Your Price
$13.42
   In Stock
Washer ROD & SPRING Assembly LEFT - WHITE
★★★★★
★★★★★
6 Reviews
PartSelect Number PS12343381
Manufacturer Part Number WH16X26911
This is a manufacturer-made suspension rod and spring assembly for your washing machine. This suspension rod is one of four suspension rods that make up the entirety of the inner suspension of your washing machine, and if worn out or damaged, must be replaced immediately. If you hear loud or excessive banging noises from your washing machine, this and/or other suspension rods within the washing machine are worn out. This specific suspension rod is the left assembly, so the parts for the other side of your washing machine will also be required when replacing this one, considering they all wear at a relatively similar rate. This suspension rod assembly is sold individually, so it does not come with any other suspension rods.
Fixes these symptoms
Installation Instructions
Donn from FREDERICKSBRG, TX
Washer was shaking while on spin cycle
Extremely easy. You will need a helper to make it easy. The best directions are on you tube. Read more...
Your Price
$39.36
   In Stock
Washer MODE SHIFTER
★★★★★
★★★★★
5 Reviews
PartSelect Number PS16554752
Manufacturer Part Number WH03X30517
This is a mode shifter or shift actuator for models of washing machine. Mode shifters are designed to change the function of the washing machine motor, between spinning cycles and agitation, and is usually installed at the bottom of the washer. If your washing machine is not spinning or agitating during its washing cycle, or if it simply does not start, this shift actuator is likely bad and in need of replacing. This shift actuator is made mostly of plastic, and features two holes to secure it with screws, as well as a single wire harness that connects within your washing machine. This shifter is an OEM part and is sold individually.
Fixes these symptoms
  • Noisy and Marks Left on Clothes
  • Spinning Issues
  • Will not agitate
  • See more...
Installation Instructions
Marvin from SHOSHONE, ID
Washer not spinning
Tilt washer back.
Remove belt gaurd.
Remove belt.
Remove pulley.
Remove clutch and shifter.
Install in reverse order
Read more...
Your Price
$12.67
   In Stock
Washer ROD & SPRING Assembly RIGHT - GREEN
PartSelect Number PS12343380
Manufacturer Part Number WH16X26910
This rod and spring assembly is designed to fit with washing machines and is made by the original manufacturer of your washer. It is a part of the washer suspension system that helps to stabilize and support the drum. The rod is a cylindrical plastic component that connects the drum to the outer frame of the washing machine. The spring is made of metal and provides tension and elasticity. The assembly is designed to absorb shocks and vibrations while the washer is running to help prevent excessive movement. If the assembly is damaged or out of alignment, the washer will be unstable and noisy. This assembly is designed to fit on the right side of the washer.
Fixes these symptoms
Installation Instructions
Donn from FREDERICKSBRG, TX
Washer was shaking while on spin cycle
Extremely easy. You will need a helper to make it easy. The best directions are on you tube. Read more...
Your Price
$33.90
   In Stock
Washer Drive Hub Kit
★★★★★
★★★★★
25 Reviews
PartSelect Number PS6012095
Manufacturer Part Number W10528947
This drive hub kit (part number W10528947VP) is for washers. Drive hub kit W10528947VP connects the spin basket to the spin shaft that spins the basket. The kit may include multiple parts; refer to your parts diagram for a complete list of parts included. Unplug the washer before installing this part. Wear work gloves to protect your hands.
Fixes these symptoms
  • Shaking and Moving
  • Spinning Issues
  • Spins slowly
  • See more...
Installation Instructions
Allison from RICHFORD, NY
Hub had warn its grooved teeth off and washer wouldnt agitate
ordered hub and it shipped quickly. I was able to put the hub in place and screw the screws in. you want to tighten them down slowly and go around to each screw tightening a little at a time so you don't break the hub. as you tighten the screws down the hub slides down flush. its impossible to just push the hub on with your hand. Buttoned it back up and got caught up on laundry. good day when the washer is fixed. Read more...
Your Price
$14.01
   In Stock
Washer Agitator Repair Kit
★★★★★
★★★★★
202 Reviews
PartSelect Number PS334650
Manufacturer Part Number 285811
This kit (Medium Cam Agitator Repair Kit, Washer Agitator Cam Repair Kit, Cam Agitator) is used to repair the agitator. These parts are located inside the agitator auger near the top. You will need to remove the softener dispenser first if your model is equipped with one. This part is driven by the output shaft of the transmission to move the clothes during a wash cycle. The agitator auger rotates one way but not the other, which forces the laundry down and out for a constant tumbling during the wash cycle. The agitator is subjected to a lot of force during the washer wash cycle. Constant and frequent use of the appliance can cause damage, especially during heavy loads. If you’re experiencing a noisy agitator, or an agitator that spins freely in both directions, then it may be in need of repairs. If your agitator is no longer agitating properly, your clothes will not tumble, and will not be washed properly. The agitator repair kit includes an agitator cam, 4 directional cogs, a bearing, thrust spacer, inner cap seal, and a washer. It is constructed of plastic and rubber, and comes in black/white.
Fixes these symptoms
  • Does not dispense fabric softener or detergent
  • Leaking
  • Marks left on clothes
  • See more...
Installation Instructions
Matt from Pawtucket, RI
Upper portion of agitator, no longer pushing clothing down.
The instructions came with the repair kit, it was fairly simple and straight foward.

One bolt held the entire agitator unit in the washer, as well as held the upper and lower halves together. Once that nut was removed the two halves seperated and the plastic clutch pieces could easily be replaced wtih the new onces in the repair kit.

Very easy do-it-yourself repair! Took about 20 minutes because I was being cautious. Next time I could do it in 5 minutes.
Read more...

Washer Brands

Related Washer Parts

Popular Washer Models

Below are the most popular Washer models we have. Enter your model number in the search box to find your model.

Genuine OEM Washer Parts

Washing machines are a household staple that help to make our lives easier and more convenient. So, it can be frustrating when your washer is not performing up to standard. Perhaps the washer will not start because the door cannot stay shut or the washer is shaky and unstable because the levelling legs are worn down. We guarantee whatever the issue is, we have heard it all before and our team is here to help.

PartSelect has been selling parts online for over 25 years to customers all over North America. Browse our extensive selection of washing machine parts such as valves, belts, and door switches from various brands including Maytag, GE, Electrolux, Whirlpool, and more.

We are here to help you save your appliance and save time and money while you do so. Repairing your washing machine is not simply good for your home and wallet, it is also great for the environment. By ordering a genuine OEM part from PartSelect and repairing your own washing machine you help to reduce the amount of waste in landfills.

  • Fit
  • Quality
  • Warranty

Common Washing Machine Problems and How to Fix Them

Troubleshooting issues with your washing machine may appear challenging but fear not. Our expert repair guides are readily available to help you find and solve any issues you may have. You can trust in our knowledge to make troubleshooting your washing machine a straightforward and successful process.

Noisy Washing Machine – Hearing unusual sounds coming from your washing machine can be concerning. There are many moving parts inside so it's common to hear humming, rumbling, knocking, and whirring noises during operation. Determining the cause can often be as easy as isolating the area of the machine where the noises originate. Often, these sounds are related to components that see regular motion and degrade over time, such as the rumbling of a clogged pump or the knocking of a worn drive belt.

Leaking Washing Machine – Noticing leaks from your washing machine can be worrisome. It's not uncommon to observe water seepage from various parts of the machine, such as the pump and connection hose. Common causes of these leaks are clogged pumps or a loose hose. By fully examining your machine and inspecting these areas you can address the issue and ensure your washing machine operates efficiently without any unwanted water spillage.

Washer Will Not Start – Experiencing difficulties with your washing machine not starting can be frustrating. Often it is related to electrical parts such as the start switch and drive motor but can also be caused by a malfunctioning lid or door switch. After ensuring the problem has not been caused by the power cable becoming loose over time due to vibrations, you should first inspect the lid or door switch for any damages which would not allow this to latch, then move on to the electrical parts such as the start switch and drive motor. By troubleshooting these areas of your machine, you can diagnose and resolve the problem, ensuring your washing machine starts and operates smoothly.

Washer Will Not Spin – Encountering issues with your washing machine not spinning can be troubling. Since your appliance has a variety of moving parts it is not uncommon to face challenges such as a worn direct drive motor coupling or a damaged door lock, all of which can affect the washer’s ability to spin, or the cycle to advance to spinning. By examining these areas, you can diagnose and address the problem, ensuring your washing machine spins properly again.

Washing Machine Does Not Drain – When your washing machine is unable to drain it may be as simple as inspecting parts crucial for efficient drainage. Most commonly we see this caused by problems such as a blockage within the inlet or outlet hose, or a blockage within the pump itself. By examining these parts, you can diagnose and address the problem, ensuring your washing machine effectively drains water after each cycle.

Related Washer Articles