Roper Parts

Roper Appliance Parts

Popular Roper Parts

Your Price
$7.70
   In Stock
Roper Rack Track Stop
★★★★★
★★★★★
118 Reviews
PartSelect Number PS11746591
Manufacturer Part Number WP8565925
The rack track stop on your dishwasher is designed to stop the dish rack at the appropriate place when opening and closing the rack. If your dishwasher is not cleaning your dishes properly, the rack stop may need to be replaced. The replacement part may differ slightly from the broken part, depending on the model. However, the different styles are interchangeable. This product is sold individually and comes in both a white and grey plastic version. Many of our customers found this repair to be very easy and takes less than 30 minutes to complete. Simply snap the old part out and snap the new part into place. You will not require any tools to complete the job. This is an authentic part approved by the manufacturer.
Fixes these symptoms
  • Door latch failure
  • Door won’t close
  • Noisy
  • See more...
Installation Instructions
Steven from WASHINGTON, DC
Upper rack wheels had begun to break off. Shoddy design and materials.
I carefully followed the video instructions step by step. They were detailed, clear, and pointed out how to avoid installation mistakes. WIthout the video I would have been tempted to just figure it out myself - ("Hey, I'm a handy guy. How hard could it be, right?"). With the video I sailed right through with no dumb errors. The new rack adjuster wheel set is much sturdier than the Whirlpool original. It made sense to get new rack stops at the same time. Thank you, PartSelect. Read more...
Your Price
$19.61
   In Stock
Roper Dryer Thermal Fuse
★★★★★
★★★★★
358 Reviews
PartSelect Number PS11741460
Manufacturer Part Number WP3392519
The Dryer Thermal Fuse (Thermal Cutoff, Temperature Fuse) is a 2 by ½ inch, white, plastic safety mechanism that stops the flow of electricity to the motor circuit when a dryer overheats. If the fuse is missing or broken, your dryer will not start. A thermal fuse fails when the exhaust temperature exceeds the fuse rating, that is when the temperature rises above the temperature that the fuse is designed to handle. This can occur when a heating element is shorted, a regulating thermostat or thermister fails, or with a partially restricted exhaust vent. The fuse attaches to the blower wheel housing. It must be replaced when there is no longer continuity between the terminals. This is a one-time fuse, meaning it cannot be re-set. The replacement part features two 3/16 inch terminals.
Fixes these symptoms
  • Drum Not Spinning
  • Heat stays on after drum has stopped
  • Not Heating
  • See more...
Installation Instructions
ANTHONY from CHESHIRE, CT
Dryer was working, but no heat.
First I unplugged the dryer, then removed the back panel, this exposed most all of the wiring and I could see the heater coils.
Not knowing what the problem was I started looking at the coils and could not see any broken parts.
So then checked the thermal fuse for continuity I removed the two wires from it with a small pair of needle nose pliers, it was held in place by two screws, once they were removed the fuse came out easily, I checked continuity with a volt meter placing the meter on X1 Ohms and could not get a reading.
I replaced with a new one and put it all back together the way I took it apart.
Then I plugged it in and it worked first time, I now have warm dry clothes.
Read more...
Your Price
$17.17
   In Stock
Roper Multi Rib Belt - 92-1/4"
★★★★★
★★★★★
379 Reviews
PartSelect Number PS346995
Manufacturer Part Number 341241
This dryer drum belt (Whirlpool Dryer Belt, Drive Belt) has four ridges, three grooves and is 1/4" wide, and 92 1/4 inches in length. It comes in black and is made of rubber. The belt transfers the rotation of the motor to turn the drum. The belt attaches to the drum, idler pulley, and motor pulley.
Fixes these symptoms
  • Drum Not Spinning
  • Heat stays on after drum has stopped
  • Noisy
  • See more...
Installation Instructions
Ray from Denton, TX
Dryer tub belt broke
Removed the two screws that attatch the lent channel to the top of the dryer, then lifted the top of the dryer by pushing in on the two locking tabs located at the front , left and right , corners of the dryer top with a small flat head screw driver. The top of the dryer will fold back out of the way. At this point I removed the two 1/4 inch screws that are located on the inside of the dryer front left and right corners that hold the front panel/door to the two side panels. Now I was able to lift the front panel up and set it to the side. The bottom of the front panel that contains the dryer door that I just removed was held on the bottom by two clips that slide into slots on the front panel and did not require any removal to disconnect the bottom of the front panel, just pull up on the front panel. Since the tub was held in place by floating on a seal at the back of the dryer and a seal on the front panel , which I just removed the tub is now free floating except for the two alignment roller wheels at the bottom of the tub. It is easier if you lay the dryer on its back at this point with front of the tub pointing up. I pulled the tub out and cleaned the years of built up lent and removed all the pieces of the old , destroyed, belt. Note, the belt tentioner is located at the front of the motor which on the bottom right hand side. If your belt is broke like mine the tensioner may/will fall to the back of the dryer when you tilt it back, but do not worry. Once the dryer was cleaned up I put the tub back in place , still on its back and made sure the two alignment rollers were in place and rolled freely when the tub was turned by hand. Another note, my original belt tensioner did not have a rolling wheel that the belt rode on , but was a semi-circle smooth surface that the belt remained in constant friction with when the dyer was running, so I made sure the replacement tensioner I ordered with my new belt did have a rolling wheel that the belt would ride on, which I believe will reduce wear and extend the belt life. The new belt came with a diagram of the belt and tensioner routing which was helpful. Note: do not take the tensioner wheel off/apart when trying to route the belt. Follow the instructions routing diagram. The tensioner is held in palce by inserting the bottom back half into the slot in the bottom floor of the dryer making sure it is aligned with the belt pully on the shaft of the dryer motor. The dryer is still on its back side. Now, it was easier for me to route the belt around the center of the tub, following the marks from the original belt, and hold in in place in a few spots with masking tape and then route it thru the tensioner and onto the front pully of the motor. Make sure you have the grooves of the belt against the tub and the grooves are aligned with the pully on the motor. Now you can remove the masking tape that was holding the belt around the tub and spin the tub by hand watching the belt making sure it is not in a bind and is traveling around the motor pully , tensioner and tub freely. Make sure the tub is still sealed on the back side wall. As you turn the tub by hand you can adjust the belt by hand so that is following the original marks around the tub left by the orignal belt. Also double check the two alingment rollers and make sure they are spinning and on track. Now put the front panel with the door on by sliding it onto the two clips that are one the bottom at each side and put the two screws in that hold the front panel to the two side panels. Now stand the dryer back up and spin the tub by hand again making sure it has a good seal on the back side and on the front panel. Pull the top back down and put the two screws in that hold the lent channle to the top. I am not sure when the belt started failing on my dryer, but was amazed at how quiet it runs now. Guess I was use to the extra noise made by a dryer that was about to die. This was a cheap and easy repair and glad I did it myself. Read more...
Your Price
$37.44
   In Stock
Roper Maintenance Kit
★★★★★
★★★★★
308 Reviews
PartSelect Number PS373087
Manufacturer Part Number 4392065
The drum support roller kit (Dryer Repair Kit) allows the dryer to tumble properly by supporting the drum cylinder. The idler pulley provides the tension required for a multi-ribbed belt. The belt attaches to the drum, idler pulley, and motor pulley. If your dryer is damaged, it may be making loud, squeaking, and/or squealing noises while the drum is turning. This is from normal wear and tear. The drum may eventually stop turning all together. This is a sign the part should be replaced. This is one complete maintenance kit. The kit includes the drum belt, drum support rollers, one idler pulley, four tri-rings, and one clip. The parts are constructed of plastic, metal, and rubber, and come in black/white/silver.
Fixes these symptoms
  • Drum Not Spinning
  • Heat stays on after drum has stopped
  • Marks left on clothes
  • See more...
Installation Instructions
DENNIS from ALTOONA, FL
Broken drive belt
Grow a second set of hands. Always unplug any appliance. Remove lint screen. remove two screws (philips Head). I took a wooden shim lightly tapped w/hammer to pop front of dryer top free. Mine worked on hinges and just flipped back til it rested against the wall. Removed two 5/16 screws inside holding face on carefully raise face section off the support clips at either side on the bottom. Pull drum out (I have the large style drum commercial size [approx.). Clean the inside free of all lint (known to be fire hazard). Sling new belt around drum. Get newly grown set of hands to hold drum in place. Pinch belt to fit between tensioner, lift tensioner and place belt around motor pulley. Spin drum couple times to make certain belt isn't twisted. Reverse dismantle proccess to put back together. Replace all parts that come with kit, you'll feel better knowing you got a new dryer, almost. Read more...
Your Price
$64.84
   In Stock
Roper Heating Element - 240V 5400W
★★★★★
★★★★★
255 Reviews
PartSelect Number PS334313
Manufacturer Part Number 279838
The heating element (Flat Can Heating Element 5400W, Heating Element, Whirlpool Dryer Heating Element, Dryer Heating Element) provides heat to the dryer. It is metal and measures 10.5 inches long, 7.5 inches wide, 2 inches deep. The element attaches to the heater housing. This part can break as a result of wear and tear. This can be material fatigue or prolonged high temperature exposure. If broken your clothes may not dry because of a lack of heat. It must be replaced when there is no longer continuity between the terminals. First check the thermal fuse on the blower housing before deciding to replace the heating element.
Fixes these symptoms
  • Heat stays on after drum has stopped
  • Noisy
  • Not Heating
  • See more...
Installation Instructions
Gadi from Irvine, CA
Dryer motor runs, but no heat
To reach the heating element you only need to open the back cover of the dryer (about 8 nut-head screws). Remember to disconnect the power.

To remove the heating element there are two small nut-head screws. Remove the two electric wires. Then you can pull the heating element away.

You can check the heating element with an ohm-meter or visually inspect it to see if the heating element spiral wire is broken.

Don't hurry to dispose the old element. My model includes a small electric safety part. You'll need to transfer it to the new heating element (that comes without it)..

Good luck.
Read more...
Your Price
$8.87
   In Stock
Roper Light Bulb - 40W
★★★★★
★★★★★
157 Reviews
PartSelect Number PS2376034
Manufacturer Part Number 8206232A
This 40w light bulb is a replacement bulb constructed of glass and metal. It is an easy-to-install electrical part which produces 40w of light. If the bulb won't light up then it may be broken and should be replaced. The bulb attaches directly to an appropriate light socket and has a small screw-in base. To access the exterior light bulb, you will need to remove the panel on the bottom of the microwave using a Phillips screwdriver. If your exterior light bulb has not been changed before, it is probably held in place with some silicone. You will need to cut away this silicone to remove the old bulb. If you cannot access the silicone with a utility knife, it can be removed using dental floss. Once the silicone is removed, simply unscrew the old bulb, and replace it with the new one. Be sure to disconnect the power to the microwave before you begin this repair. This light bulb measures about 1 1/8 inches. We do not recommend using a higher-wattage bulb for this appliance, and can only recommend this specific bulb. If fixing the bulb does not solve your microwave light issue, it's possibly a problem with the socket, which means the socket and/or board will need to be replaced. This can be a more dangerous repair, so consult your user manual or a technician before attempting.
Installation Instructions
Chris from Cedar Hill, TX
Burned out light under microwave and Filters needed changing
I just removed the multiple screws which held the hood cover on. I then attempted to remove the light bulbs from the socket. This proved impossible because the bulbs were so fragile from the heat and grease build up. To make this task much easier and probably safer, just replace the bulb housing and light bulb. The bulb housing unplugs very easily. Just replace it then screw your new bulb in. P.S. Be sure to unplug appliance before you start.

The filters are very easy to replace. No tools needed.

Hope this helps.
Read more...
Your Price
$4.39
   In Stock
Roper Agitator Directional Cogs
★★★★★
★★★★★
358 Reviews
PartSelect Number PS388034
Manufacturer Part Number 80040
This kit is used for replacing the agitator directional cogs (Agitator Dogs, Agitator Repair Kit, Washer Agitator Dogs, Agitator Dog Ears). The agitator is what creates the thrusting motion in your washer to tumble your clothes during the washer cycle. Your agitator will rotate one way, and not the other. The agitator dogs are what prevent the agitator from rotating in both directions, while allowing it to rotate in one direction. Your agitator cogs may be malfunctioning if you can manually rotate the agitator in both directions. If broken they will need to be replaced. Cogs can be found by simply removing the softener dispenser and then removing the agitator cap. The are attached to the agitator. This replacement part features 4 agitator directional cogs. There are 4 cogs per package that are made up of high-quality plastic. This part comes in white/beige.
Fixes these symptoms
  • Does not dispense fabric softener or detergent
  • Marks left on clothes
  • Not cleaning dishes properly
  • See more...
Installation Instructions
mike from Kent, WA
washer wouldn't agitate
First pry off the cap of the agitator. Then using a socket remove the bolt that holds the plastic cup in place. Remove this cup by prying it loose from the two tabs that hold it in place. Once this cup is removed you can get to the broken cogs.
Slip the new cogs into the underside of the cup, and slide the cup back down in the agitator housing using the slots on the side for a guide. (You may want to remove the entire agitator and assemble everything upside down, then flip it all back over to mount, so the cogs don't fall out).
Tighten the bolt, snap the cap back in place on top of the agitator and your'e done. Easy repair.
Read more...
Your Price
$27.94
   In Stock
Roper Dryer Cycling Thermostat
★★★★★
★★★★★
97 Reviews
PartSelect Number PS11741405
Manufacturer Part Number WP3387134
This thermostat (Dryer Operating Thermostat, Dryer Cycling Thermostat, Cycling Thermostat, Dryer Thermostat) is used to maintain a temperature of 155 degrees in the dryer drum. The internal bias heater also allows this thermostat to provide a low heat temperature of approximately 140 degrees when the low temperature setting is selected. The part measures 2 by 1.5 inches, comes in black/silver and is constructed of plastic and metal. The thermostat attaches to the blower wheel housing.
Fixes these symptoms
  • Heat stays on after drum has stopped
  • Not Heating
  • Too hot
  • See more...
Installation Instructions
Tom from High Point, NC
Dryer blew cold air.
PartSelect is great for providing parts as requested. Unfortunately, neither of the 2 parts I ordered were on my machine. My bad for not looking at the actual part instead of the description. A word to the wise! Read more...
Your Price
$37.67
   In Stock
Roper Refrigerator Door Shelf Bin - White
★★★★★
★★★★★
234 Reviews
PartSelect Number PS11739091
Manufacturer Part Number WP2187172
This refrigerator door shelf bin, also known as the door bin, or sometimes just a "bucket", is an authentic manufacturer-certified part made of white plastic and is easy to install. It is used to hold items in the fridge door, like jars, cans, and bottles, and you'll be able to visually see if the part is broken or warped. This particular shelf attaches directly to the fridge door; you should be able to pull out the old bin and snap the new one into place by observing the slots and pushing the bin down into them. You can check if this model is right for your appliance by checking your user manual and model number. The door bin measures about 18 inches wide, 4.5 inches high, by 7 inches deep. This door shelf bin is sold individually, so if your refrigerator takes multiple bins, which many do, you will need to order the appropriate amount of bins.
Fixes these symptoms
  • Door won’t open or close
  • Ice maker not making ice
  • Leaking
  • See more...
Installation Instructions
Charles from Dallas, TX
One of my door bins and filter cap broke.
I searched the model number for my Whirlpool refrigerator on the internet and partselect.com came up so I clicked on it. The site asked for my model number which I typed in and there it was...a picture of my refrigerator in full detail and very well diagramed and labeled. I found the number of the parts I needed, added them to my cart and paid. In a few days (2 I think which is an awsome delivery time) the parts were iin my front door step, very well packaged and in imaculate condition. I took them out of the box and installed them in less than 15 minutes. A parts internet order and repair has NEVER gone as quick and easy as this did. Thankyou Partselect for an awsome job and awsome website and even more awsome delivery time. Very happy and impressed with your service. Keep up the outstanding work!!!!!! Read more...
Your Price
$79.56
   In Stock
Roper Refrigerator Crisper Drawer with Humidity Control
★★★★★
★★★★★
404 Reviews
PartSelect Number PS11739119
Manufacturer Part Number WP2188656
The crisper drawer (Crisper Pan, Refrigerator Crisper Drawer) with humidity control is meant to keep your vegetables and fruit as fresh as possible by allowing you to regulate the humidity levels within the drawer. It attaches on the inside of your refrigerator to the bottom of the crisper shelf. This drawer can break from misuse or accidental damage. It is also subject to material fatigue over time. If broken or damaged, it may be difficult to slide the drawer in and out, and it should be replaced. This plastic drawer measures 14.92 inches long, 7.6 inches high, and 16.5 inches wide and comes in white/clear.
Fixes these symptoms
  • Clicking sound
  • Door Sweating
  • Door won’t open or close
  • See more...
Installation Instructions
JULIA from BRONX, NEW YORK, NY
replacing parts only
the prices you had were great, now I see there was an increase in the parts.
thank you
Read more...

Roper Appliance Types

Popular Roper Models

Below are the most popular Roper models we have. Enter your model number in the search box to find your model.