Models > FFBD2411NS0A > Symptoms > Not cleaning dishes properly

Parts That Fix Frigidaire Dishwasher FFBD2411NS0A Not cleaning dishes properly

Not cleaning dishes properly is a commonly reported symptom for the FFBD2411NS0A Frigidaire Dishwasher, and we have put together a full guide on how to fix this. This advice is based on feedback from people who own this exact appliance. We have listed the most common parts for your FFBD2411NS0A Frigidaire Dishwasher that will fix Not cleaning dishes properly. We have included repair instructions, and helpful step-by-step video tutorials. If you are experiencing this issue, not to worry, DIYers just like you have fixed this, and shared their experience to help you!

Fixes Symptom 34% of time
★★★★★
★★★★★
123 Reviews

Rated by 52 customers 

  

Really Easy 

Less than 15 mins 

Ratings submitted by customers like you who bought this part.   

The Lower Spray Arm is used in your dishwasher to spray water and clean your dishes. If broken there will be visible damage or your dishes may no longer be cleaned properly. If your spray arm is broken (due to general wear or high heat), it should be replaced. Your lower spray arm will be located at the bottom of your dishwasher tub. Check your user manual and model number to ensure this model is right for you. This version is plastic and metal and comes in gray/blue. We recommend you wear work gloves to keep your hands safe when installing and disconnect power to the appliance. You will also want to make sure that you turn off the water supply to your dishwasher. From here, you will want to open the dishwasher, pull out the lower rack and set it aside. Remove the lower wash arm. On each side of the bottom of the spray arm, there are small locking tabs that can be pushed aside using a flathead screwdriver. Once released, the spray arm can easily be pulled off the dishwasher. Put the new lower wash arm in place and push it down to lock it in. Ensure it is spinning freely and does not hit the heating element. Return the lower dish rack into place and then close the dishwasher door.

$ 35.44
  In Stock
PartSelect Number PS12585623
Manufacturer Part Number 5304517203

Replacing your Frigidaire Dishwasher Lower Spray Arm

Replacing your Lower Spray Arm

Customer Repair Stories

Spray arm fell over and melted on the heating element.

It required no tools. It took less than one minute to connect the spray arm to the bottom of the unit. Our dishwasher is working perfectly now.
  • Inge from Hernando, FL
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
81 of 94 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!

spray arm keeps melting

I have had to keep replacing the spray arm on the bottom of my dishwasher which takes like 2 seconds to do.. First you open the dishwasher and than pull the bottom basked forward and reach down and pull the spray arm up and pop the bottom of the spray arm off and put it on the new spray arm and slip it back into the dishwasher over the thing that makes it spin around.. but the tricky part is and I didn't know this and this is why my dishwasher spray arm kept falling over and melting on the heating element.. you have to turn it till it clicks in.. and your done..
  • Donna from Madison, OH
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
270 of 281 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Fixes Symptom 30% of time
★★★★★
★★★★★
71 Reviews

Rated by 81 customers 

  

Really Easy 

Less than 15 mins 

Ratings submitted by customers like you who bought this part.   

This spray arm is a genuine OEM replacement part for your dishwasher. This spray arm is for the upper part of your dishwasher. No tools are required for this repair, simple remove the rack stops and upper dish rack, then disassemble the mount and spray arm before installing the new one.

$ 36.21
  In Stock
PartSelect Number PS11770483
Manufacturer Part Number 5304506516

Replacing your Frigidaire Dishwasher Upper Spray Arm

Replacing your Upper Spray Arm

Customer Repair Stories

upper spray arm retainer nut failed

simple repair..woke up one morning and after the dishwasher cycled, I noticed the upper spray arm laying on the top tray.
ordered new one from site, was delivered with-in 2 days ( with standard shipping) all 1 piece, took seriously 5 seconds to unscrew by hand and replace!
  • Michael from Hillsdale, NJ
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
50 of 51 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!

The spray arm would fall off during the washing cycle.

Repair was simple. I unscrewed the old grommet which held the old spray arm and screwed-on the new one. About 30 seconds was required. Other people having this problem should note that the spray-arm is made of three pieces which are inseparable when the arm is new. The arm is sold in this form. However, when your machine is having the problem that the arm falls off, the three pieces become separate. When you want to replace the spray arm, only one new part needs to be ordered because this part encompases all three components.
  • Roy from Worcester, MA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
818 of 832 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Fixes Symptom 8% of time
★★★★★
★★★★★
6 Reviews

Rated by 4 customers 

  

Really Easy 

15 - 30 mins 

Ratings submitted by customers like you who bought this part.   

Upper Rack Assembly - T3 PRO. This is the complete upper rack and the wash arm.

$ 135.57
  In Stock
PartSelect Number PS10065024
Manufacturer Part Number A01986801

Customer Repair Stories

Top spray bar rear gasket failed

Replaced the entire top rack with spray bar.
  • tom from PASADENA, MD
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
12 of 20 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!

Center spray arm broke

I was able to pull out the top basket were the glasses are put then I lined up the back and the center plastic clip an slid on the center spray arm. It took about 2 miniutes
  • Keith from Coventry, RI
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
40 of 89 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Fixes Symptom 4% of time
★★★★★
★★★★★
17 Reviews

Rated by 8 customers 

  

Really Easy 

15 - 30 mins 

Ratings submitted by customers like you who bought this part.   

This lower spray arm is a genuine OEM part for various makes and models of dishwasher and is sold as an individual part. This part attaches to the lower spray assembly of your dishwasher and the lower spray arm itself clips into this part to facilitate its spinning movement during the washing cycle. To replace it, remove the spray arm by pulling it out, remove the surrounding circular clip and then twist to remove this bit. Made completely of plastic, this part measures approximately 3-inches deep, 2-inches wide, and 3.125-inches tall.

$ 11.27
  In Stock
PartSelect Number PS12712289
Manufacturer Part Number 5304518968

Replacing your Frigidaire Dishwasher Lower Spray Arm Support

Replacing your Lower Spray Arm Support

Customer Repair Stories

missing bottom spray arm

I used the PartSelect repair video online to show me how to fix the dishwasher. I needed a spray arm and support. Excellent video made the repair quick and easy.
  • Ashley from Normal, IL
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!

spray arm fell off and melted on element

The Spray arm and the support had come off during operation and subsequently melted on the heating element. This was our fault, as a knife had slipped through the lower dish-rack and acted as a ramp to launch the spray arm as it came around. The support was a simple 1/4 turn counter-clockwise until it clicked into place, drop the strainer basket into position around the support, them push the spray arm into place until the catches snap over the retaining ring molded into the support. All told, about 10 minutes, max.
  • Dale from Worley, ID
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
34 of 38 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Fixes Symptom 3% of time
★★★★★
★★★★★
11 Reviews

Rated by 8 customers 

  

Really Easy 

30 - 60 mins 

Ratings submitted by customers like you who bought this part.   

This kit includes the motor and o-rings.

$ 164.17
  In Stock
PartSelect Number PS3497737
Manufacturer Part Number 154844301

Replacing your Frigidaire Dishwasher Pump Motor Kit

Replacing your Pump Motor Kit

Customer Repair Stories

Water leak behind kick-plate

See posting under O rings. Get schematic Motor & Pump pg. 8 from pub # 5995487674. Steps: 1) run cycle so most water is pumped out of dishwasher 2) remove front cover to reduce weight of door; 3) disconnect electric plug, hot water hose [NOTE: be prepared for some water from hose], and waste tube all usually found under sink area; 4) remove 2 screws at top of front panel; 5) lower leveling feet to allow best clearance; 6) put towels under front feet to protect floor and slide unit out from under counter; 7) place heavy blanket next to unit to protect floor and tip unit over on its side; 8) disconnect electric plug from motor and remove metal spring clip holding motor (2 torx screws) and pull clip off motor; 9)gently rock motor while lifting to remove from unit [NOTE position of motor for reassembly]; 10) put thin coat of silicon on O rings and place on new motor [look at old motor to make sure O rings are in proper slots; 11) line up motor and gently push new motor back into position; 12) reverse disassemble steps above. 13) run dishwasher through fastest cycle to check for leaks.
  • Larry from EDWARDS, CO
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Screw drivers, Socket set, Wrench set
58 of 77 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!

not cleaning, spray arms not working

The hardest part was disconnecting the dishwasher. the motor is located on the bottom so after pulling it out and laying it down on the front of the machine the motor unplugs and 2 screws hold it in place.The new motor comes with "O" rings so I applied a little grease and put it back together. 2 minutes to replace motor, 15 minutes to disconnect water and electric, 15 to reconnect.
  • Jeff from Lancaster, PA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver, Screw drivers, Wrench (Adjustable)
93 of 115 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Fixes Symptom 3% of time
★★★★★
★★★★★
82 Reviews

Rated by 51 customers 

  

Really Easy 

Less than 15 mins 

Ratings submitted by customers like you who bought this part.   

$ 232.87
  In Stock
PartSelect Number PS17219739
Manufacturer Part Number 5304535768

Customer Repair Stories

rack had worn rust spots on tines

replaced with new lower rack, out with the old, in with the new! Shipping was great new part arrived in 2 days! Great service, and will use again for all parts needed in the future, and will tell everyone about this site! Thanks a bunch!
  • Gregory from Port St Lucie, FL
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
8 of 11 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!

Old rack had broken tines and rust

No repair, just replaced the lower rack. Your service is awesome. I received my shipment next day. Thank you so much. I will definitely use your service again.
  • Karen from Alachua, FL
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
21 of 21 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Fixes Symptom 3% of time
★★★★★
★★★★★
2 Reviews

Rated by 2 customers 

  

A Bit Difficult 

1- 2 hours 

Ratings submitted by customers like you who bought this part.   

This grommet fits on the spray arm of your dishwasher. This replacement part connects and seals the spray arm to the water hose that supplies water to the dishwasher tub. Be sure to shut off water supply to your appliance before completing this repair. This part is 3 inches in diameter and is off-white in color.

$ 18.02
  In Stock
PartSelect Number PS11770484
Manufacturer Part Number 5304506517

Replacing your Frigidaire Dishwasher Water Delivery Tube Grommet

Replacing your Water Delivery Tube Grommet

Customer Repair Stories

Replacing grommet

Finally we laid in the tub--be sure to support the lid. The grommet could be inserted halfway. Then trying to fold the grommet back we were able to use a screwdriver to force the rest in to place.
  • Jack from KENDALLVILLE, IN
  • Difficulty Level:
    Very Difficult
  • Total Repair Time:
    More than 2 hours
  • Tools:
    Pliers, Screw drivers
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!

wrong part

FRIDGEADAIRE - GALAXY SERIES -Part arrived within 3 days of order BUT it was wrong part. All excited about getting the upper wash rack in full operation once again. Pilled shelf out to remove gasket to find it looked nothing like the one on there. The part I need is like a bellows of sorts that fits on the water line attached to the upper shelf. The part received goes on the back wall.
Now i am back at square one with part I don't need and hoping for the part I do need
  • Loraine from HYDE PARK, VT
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
11 of 14 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Fixes Symptom 3% of time
★★★★★
★★★★★
1 Review

Rated by 2 customers 

  

Really Easy 

Less than 15 mins 

Ratings submitted by customers like you who bought this part.   

This filter is for dishwashers. The filter removes food particles and debris from the water to prevent the drain from clogging. Follow the instructions in the manual when installing this part.

$ 21.62
  In Stock
PartSelect Number PS11770489
Manufacturer Part Number 5304506525

Replacing your Frigidaire Dishwasher Dishwasher Filter

Replacing your Dishwasher Filter

Customer Repair Stories

dishes not comming out clean

removed all strainer and filter parts and soaked them in lime remover for several hours until clean. then,I rein stalled all the parts including the new filter screen.
  • JOHN D from ROCKPORT, TX
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    More than 2 hours
Was this instruction helpful to you?
Thank you for voting!

Replace filter in dishwasher

Watching a YouTube video that was attached to an email, I was able to install my new dishwasher filter in no time without any tools. Thank you.
  • Gary from NEW KENSINGTN, PA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
3 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Fixes Symptom 2% of time
★★★★★
★★★★★
43 Reviews

Rated by 29 customers 

  

Easy 

15 - 30 mins 

Ratings submitted by customers like you who bought this part.   

This water inlet valve is usually located behind the lower kickplate panel in either the right or left corner of the dishwasher. The attaching solenoids on the valve open and close according to the desired amount of water needed. The water inlet valve on your dishwasher supplies water to the dishwasher. If your dishwasher is leaking because it has overflowed, the water inlet valve may be the cause. If your dishwasher continues to fill above the heating element, try opening the door latch to see if it stops filling. If it continues to fill, you have a defective inlet valve that will need to be replaced.

$ 57.14
  In Stock
PartSelect Number PS1990907
Manufacturer Part Number 154637401

Replacing your Frigidaire Dishwasher Water Inlet Valve - 120V 60Hz

Replacing your Water Inlet Valve - 120V 60Hz

Customer Repair Stories

No water to dishwasher on any cycle

Unplugged dishwasher, pulled it out. Unclamped hose and unscrewed water source to inlet valve, removed wiring harness, unscrewed bracket and reinstalled new valve. Now have a functioning dishwasher.
  • David from Las Cruces, NM
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Pliers, Screw drivers, Wrench (Adjustable)
41 of 48 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!

Leak in the water inlet valve/solinoid

1. Shut off water supply.
2. Removed inlet water hose where it connects to the vavle assembly.
3. Removed the two bracket screws holding the assembly to the frame, and detached the electrical connection from the solinoid.
4. Removed the inlet hose adapter connection from old valve and installed into new valve.
5. Attached electrical connection to new valve solinoid.
6. Remounted assembly to the frame.
7. Re-attached the inlet water hose to the hose adapter connection on the valve.
8. Turned on the water, washed some dishes.
  • Mickey from Ooltewah, TN
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Pliers, Screw drivers, Wrench set
154 of 169 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Fixes Symptom 2% of time
★★★★★
★★★★★
1 Review

Rated by 6 customers 

  

Really Easy 

15 - 30 mins 

Ratings submitted by customers like you who bought this part.   

Sold individually.

$ 10.61
  In Stock
PartSelect Number PS421211
Manufacturer Part Number 154406401

Replacing your Frigidaire Dishwasher Delivery Tube Gasket

Replacing your Delivery Tube Gasket

Customer Repair Stories

Spinner fell off of delivery tube.

Wrap your pliers in some kind of padding so you don't damage the plastic. Spin the base ( not the spinner itself) which is left-threaded(normal). If the gasket doesn't fall out (mine did) pull it out gently. Clean the gasket socket with a rough cloth or scotch-brite pad and install the new one. Put it all back together and wash dishes, man.
  • Jeffrey from Rougemont, NC
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Pliers
Was this instruction helpful to you?
Thank you for voting!

Dishwasher Leakibng

Removed the bottom covering on dishwasher and then ran it to figure out where the leak was coming from. Noticed it was dripping off hose, but not actually leaking from hose.

Unplugged dishwasher and slid it out from cabinet area (be sure to turn off and disconnect water supply)

Followed delivery tube up side of dishwasher to top of tub and noticed reminents of where water ran down side of tub.

Loosened delivery tube by plastic nut inside of tube and removed. Noticed gasket was partially depleted.

Ordered new gasket, replaced and put everything back together. (Be sure to use teflon tape on water source fitting and tighten firmly). No leaks
  • Eric from Benton, KY
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Pliers, Wrench (Adjustable)
10 of 12 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Fixes Symptom 1% of time
★★★★★
★★★★★
22 Reviews

Rated by 32 customers 

  

Really Easy 

Less than 15 mins 

Ratings submitted by customers like you who bought this part.   

The upper dishrack is used to hold your dishes in place while the dishwasher goes through the wash cycles. Over time the dishrack can become damaged, start to rust, or be missing rollers, and the dishrack will need to be replaced. This rack is white in color with light gray rollers and measures approximately 23 Inch x 23 Inch. This is a genuine OEM part.

$ 126.15
  In Stock
PartSelect Number PS17219604
Manufacturer Part Number 5304535251

Replacing your Frigidaire Dishwasher RACK ASSEMBLY UPPER

Replacing your RACK ASSEMBLY UPPER

Customer Repair Stories

Top rack had rusted

Slid the rack out, removed the end pieces holding top rack in the sliding arms. Removed the spray arm. It was stiff & a bit hard to get off, but with a little careful prying it came off. Put that spray arm assembly back onto the new rack, slid the new rack back in place, put the end pieces back on and in less than 15 minutes, we were done. Part came in very quickly, I might add. I feel like I have a brand new dishwasher.
  • Sharon from Alamogordo, NM
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Pliers, Screw drivers
2 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!

the rack had broken on one of the arms that connect to the wheel in the slider

I unclipped the plastic pieces at the front of the rack. This was very easy. Then I removed the old rack. I then removed the water sprayer from the old rack and placed it on the new rack. This was simple and I unscrewed the water sprayer by hand and snapped out. Putting it on the new assembly was very easy. Then I placed the new rack on the two stainless steel sliders and refastened the plastic clips at the ends. It was no problem.
  • Joseph from Louisville, TN
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
6 of 10 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Fixes Symptom 1% of time
★★★★★
★★★★★
3 Reviews

Rated by 1 customer 

  

Really Easy 

15 - 30 mins 

Ratings submitted by customers like you who bought this part.   

Located at the bottom of the dishwasher, this filter keep large particles of food and foreign objects away from the pump.

$ 17.80
  In Stock
PartSelect Number PS11770494
Manufacturer Part Number 5304506533

Replacing your Frigidaire Dishwasher Filter Base

Replacing your Filter Base
Fixes Symptom 1% of time
★★★★★
★★★★★
30 Reviews

Rated by 14 customers 

  

Really Easy 

Less than 15 mins 

Ratings submitted by customers like you who bought this part.   

The silverware basket, used for dishwashers, is in the bottom dishrack. The lower dishrack basket is used to hold eating utensils such as spoons, forks, and knives, and other small tools. If the basket in the dishwasher is worn out or the basket is broken, replacing it can be a solution. No tools for this replacement are required, as it is an easy process. If you need further guidance refer to the instructions provided by the manufacturer. For safety precautions make sure to unplug the dishwasher and wear gloves.

$ 36.52
  In Stock
PartSelect Number PS17219661
Manufacturer Part Number 5304535382

Replacing your Frigidaire Dishwasher Silverware Basket

Replacing your Silverware Basket

Customer Repair Stories

silverware basket skunked

tossed the old one a replaced with a new.Hardest 10 second repair ever....It took 10 seconds had to open and close the door.
  • Alan from Holley, NY
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
13 of 14 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!

large holes in the bottom of the basket where pieces of plastic kept breaking off

I replaced the basket. No tools necessary. New basket seems sturdier than original. Very satisfied with my purchase.
  • Lauren from Peabody, MA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
18 of 21 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Fixes Symptom 1% of time
★★★★★
★★★★★
8 Reviews

Rated by 7 customers 

  

Easy 

30 - 60 mins 

Ratings submitted by customers like you who bought this part.   

This dishwasher heating element is not designed to heat the water that enters it, but is designed to maintain the heat of the water that enters the dishwasher. It is located on the bottom of the dishwasher. NOTE: Brass nuts are NOT included. Must be ordered separately.

$ 73.63
  In Stock
PartSelect Number PS3653449
Manufacturer Part Number 154825001

Customer Repair Stories

Heating Element was corroded.

It took me about 30 minutes to do the repair - took my time and could’ve done it much faster.
  • Christopher from EVERETT, WA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Nutdriver, Screw drivers, Wrench (Adjustable)
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!

Heating element went out

Removed the clamp holding it to the floor and
removed the c-clips holding element underneath
and put new one in. Hard part was figuring out
what was holding the element but since I still
had the schematic drawing we figured it out.
Saved a bunch on a repairman. After watching
my friend install the new element I could probably
do it myself next time.
  • Jane from Port Charlotte, FL
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Screw drivers, Wrench (Adjustable)
14 of 23 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Fixes Symptom 1% of time
★★★★★
★★★★★
3 Reviews

Rated by 3 customers 

  

Really Easy 

15 - 30 mins 

Ratings submitted by customers like you who bought this part.   

Part is found under the lower spray arm.

$ 51.04
  In Stock
PartSelect Number PS420500
Manufacturer Part Number 154252701

Replacing your Frigidaire Dishwasher Drain Trap

Replacing your Drain Trap

Customer Repair Stories

several issues with dishwasher

Easy fix but not cheap
replaced drain trap and four rack wheels with clips

All parts were expensive for the items.
found cheaper wheels w/clips for much less on another site.
  • Nicholas from KESWICK, VA
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
3 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Fixes Symptom 1% of time
★★★★★
★★★★★
6 Reviews

Rated by 30 customers 

  

Really Easy 

Less than 15 mins 

Ratings submitted by customers like you who bought this part.   

The single rack roller kit comes with one axle/clip and one wheel/roller. The rack wheel is designed to allow the rack of your dishwasher to roll in and out. If the rack will not complete this task, or you notice that your dishwasher is not cleaning dishes properly, you may need to replace the rack wheel. The single rack roller kit is made of white plastic, and clips to the dishwasher rack with the included axle/clip. Many of our customers have described this repair as easy, and you will not require any tools to complete it. Lower rack roller and bracket assembly, grey. Wheel has been updated. If wheel pictured is not like old one, you may need to replace all wheels.

$ 6.88
  In Stock
PartSelect Number PS16745479
Manufacturer Part Number 5304532229

Customer Repair Stories

plastic attachment for wheel to rack had dried and broken

removed the remnants of the old wheels and popped the new ones on....simple

Got to say, I was pretty amazed that I received my order the following day! You guys are wonderful!
  • Marla from Columbia, TN
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
66 of 131 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!

Lower Rack Roller Missing

Took the roller out of the package, snapped it into place. Less than 15 seconds. Works good as new.
  • Sandra from Mount Vernon, WA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
376 of 383 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Fixes Symptom 1% of time
★★★★★
★★★★★
182 Reviews

Rated by 85 customers 

  

Really Easy 

15 - 30 mins 

Ratings submitted by customers like you who bought this part.   

This dishwasher door gasket (Bottom Gasket, Gasket, Door Seal, Dishwasher Door Lower Seal) helps prevent water from leaking out of the bottom edge of your dishwasher door by creating a watertight seal. This part is attached to the bottom of your dishwasher inner door panel. It is frequently exposed to water and detergent during its lifetime. The water and chemicals can eventually wear down the gasket and compromise the integrity of the seal. If the gasket is malfunctioning, the integrity of the door seal will be effected. You will notice leaking through the bottom of your dishwasher door. If your dishwasher is leaking water from the bottom of the door, first inspect the seal for food particles near the bottom and sides, and remove the buildup, as it can stop the door from closing properly and keeping a tight seal; if not, you may need to replace the bottom door gasket. Check the door gasket for tears, cuts, or wear. This part is sold individually and measures 22.5 inches by 1.25 inches. It is constructed of plastic, and comes in yellow/grey. Includes one lower door gasket.

$ 21.08
  In Stock
PartSelect Number PS9495545
Manufacturer Part Number 809006501

Replacing your Frigidaire Dishwasher Dishwasher Bottom Door Gasket

Replacing your Dishwasher Bottom Door Gasket

Customer Repair Stories

Leaking under door

Received the part 3 working days after order. Part was exactly like the original.
Removed the door. Slipped off old gasket and replaced with new gasket. Replaced door and tried rinse cycle. Worked perfectly.
  • Ronald from Berwick, PA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
109 of 128 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!

Bottom Door Seal fell apart and started leaking.

First I opened the door all the way. Second I reached down to the bottom gasket then grabed it on the right end of the seal that is on the right side of the door. Then I pulled the end outward from the bottom of the door toward the heater coil in the bottom of the washer. It came out real easy. You see it just snaps into a little plastic groove under the door. I then cleaned up the area for food and soap particules. I then placed the new gasket in place by lining up the notch toward the right end with the piece of plastic that encloses the right end of the plastic notch on the bottom right end of the door. Then push it in untill it stops going into the notch. It snaps in but does not make a snaping sound. It just won't go in no more.
  • Scott from Flowood, MS
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
381 of 427 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Fixes Symptom less than 1% of time
★★★★★
★★★★★
42 Reviews

Rated by 41 customers 

  

Really Easy 

15 - 30 mins 

Ratings submitted by customers like you who bought this part.   

This grey OEM dishwasher tub gasket is a 73" grey rubber part that creates a seal around the dishwasher to prevent any water leakage during a cycle. If it's damaged or broken, you'll start seeing water leaking out. If broken, it should be replaced. Refer to your model number and user manual to ensure this part is right for you. When making this repair, open the dishwasher door and take out the lower dish tray for better access. Pull out the old gasket, and clean the channel with a rag. Push the new gasket into place into the notch on the door, which you should see upon close inspection, using a flat-head screwdriver for assistance if necessary. We do not recommend cutting any additional length off on the tub gasket if any is present during your repair.

$ 32.44
  In Stock
PartSelect Number PS8260227
Manufacturer Part Number 154827601

Replacing your Frigidaire Dishwasher Dishwasher Tub Gasket - Gray

Replacing your Dishwasher Tub Gasket - Gray

Customer Repair Stories

Dishwasher was leaking at the lower left side of the door.

Probably the easiest repair job that you could encounter. I removed the old gasket from the door frame. Cut the new gasket to length and pushed it into the door frame.

Water leak solved...
  • John from Hummelstown, PA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
21 of 24 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!

dishwasher was leaking water

I removed old tub gasket, which the door presses against to make a seal, and put the new one in. Flat tip screwdriver was used to gently press gasket in.
  • Charles from Milton, FL
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
175 of 201 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Fixes Symptom less than 1% of time
★★★★★
★★★★★
6 Reviews

Rated by 6 customers 

  

Really Easy 

30 - 60 mins 

Ratings submitted by customers like you who bought this part.   

This is the replacement detergent dispenser for your refrigerator. It is gray in color and is sold individually. It is approximately 8.5 inches long and 3 inches wide. The detergent dispenser stores the detergent until it is ready to be dispensed. If your dishes are not coming clean, or you notice the detergent is still in the dispenser at the end of the cycle, you may have a damaged or malfunctioning detergent dispenser. This is an OEM part sourced directly from the manufacturer.

$ 82.28
  In Stock
PartSelect Number PS11770487
Manufacturer Part Number 5304506521

Replacing your Frigidaire Dishwasher Detergent Dispenser

Replacing your Detergent Dispenser

Customer Repair Stories

Leaked spot free fluid

Replaced part
  • Tim from MARINE ST CRX, MN
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Pliers, Screw drivers
2 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!

The soap dispenser didn’t dispense the soap

After shutting off power to the dishwasher, I removed the two screws holding the door cover on the inside of the door sides, about 8 inches from the bottom of the door. I slid the cover down and off, and unplugged the wires to the dispenser. Then I removed the six screws holding the dispenser in place, removed the old dispenser, installed the new one, replaced the six screws and plugged the wires back in. The door cover and the two screws was all that was left. It took about ten minutes. Easy.
  • Bernard from ACUSHNET, MA
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
4 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Fixes Symptom less than 1% of time
★★★★★
★★★★★
20 Reviews

Rated by 3 customers 

  

Really Easy 

15 - 30 mins 

Ratings submitted by customers like you who bought this part.   

If your dishwasher is leaking or not draining properly, you may need to replace the drain hose. The drain hose connects to the pump located below the lower spray arm and aids in proper dishwasher drainage. This white and black plastic hose is 7.5 feet long. For this repair, you will need either a 1/4-inch or 5/16-inch nut driver, depending on your model. You will need to remove the lower access panel on your dishwasher to complete this repair; it is often easier to remove the dishwasher from the cabinet to do so. Be sure to disconnect the dishwasher from both the power and water supply before completing this repair.

$ 26.68
  In Stock
PartSelect Number PS9494138
Manufacturer Part Number 807117001

Replacing your Frigidaire Dishwasher Dishwasher Drain Hose

Replacing your Dishwasher Drain Hose

Customer Repair Stories

A hole in the dishwasher dicharge hose.

I had to remove the dishwasher from under the counter, flip it on it's side to gain access to the discharge hose attachment point, removeit, remove the other end of the hose from the sink-side and replace the hose. The sink-end of the hose has a 'collar' that must be cut to fit the fitting on the sink.
  • Lee from Columbus, OH
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver, Screw drivers
22 of 47 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!

Drain hose was missing

My friend bought a used dishwasher at a garage sale, the previous owner had thrown away the drain hose because it was "nasty" they said....remember it could have been cleaned. When I went to install it, I removed the old washer, and discovered that the old hose would not fit on the replacement dishwasher. I went to the local repair shop, armed with the model and serial #'s. they searched and searched their books and could not find the hose part number. they said "good luck" when I left...I went home and looked up the model on your web site, ordered the hose, and in 3 days had the dishwasher installed and running in about 30 minutes...thanks for prompt shipping.. I couldn't believe it arrived so soon...Mowerman
  • John from Carthage, MO
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers, Wrench set
40 of 46 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!