Models > HRNT15152A

HRNT15152A (CF17A) Hoover Refrigerator - Overview

Sections of the HRNT15152A

[Viewing 1 of 1]
FREEZER COMPARTMENT Diagram and Parts List for CF17A Hoover Refrigerator
FREEZER COMPARTMENT
Keep searches simple, eg. "belt" or "pump".
Screw – Part Number: W11233072
Screw
★★★★★
★★★★★
(6)
PartSelect #: PS12349731
Manufacturer #: W11233072
This is a multi-use and multi-appliance screw. It can be used on a microwave, refrigerator, range/oven, air conditioner, dehumidifier, washer, or dryer. The measurements of this screw are 8 x 1/2 inch...
$20.83
  In Stock
Ice Cube Tray – Part Number: WP61002140
Ice Cube Tray
PartSelect #: PS11743133
Manufacturer #: WP61002140
This ice cube tray is located inside your refrigerator and is eleven inches long, with 48 molds. It comes in white and is made entirely from plastic. If your tray is broken, cracked, or damaged, repla...
$26.50
  In Stock
Icemaker Fill Tube – Part Number: 12001935
Icemaker Fill Tube
PartSelect #: PS2003449
Manufacturer #: 12001935
This fill tube grommet is used to supply water to the icemaker and is partially located in the refrigerator/freezer wall.
$41.05
  In Stock
FOAM SEAL – Part Number: 68866-4
FOAM SEAL
PartSelect #: PS2073135
Manufacturer #: 68866-4
  No Longer Available
SEPARATOR – Part Number: 66460-1
SEPARATOR
PartSelect #: PS2065126
Manufacturer #: 66460-1
  No Longer Available
PAN-ICE – Part Number: 60653-1
PAN-ICE
PartSelect #: PS2057284
Manufacturer #: 60653-1
  No Longer Available
DISCONTINUED – Part Number: 24580-3
DISCONTINUED
PartSelect #: PS2026256
Manufacturer #: 24580-3
  No Longer Available
WASHER- SP – Part Number: 420092-900
WASHER- SP
PartSelect #: PS2042246
Manufacturer #: 420092-900
  No Longer Available
SEAL- FRON – Part Number: 67730-1
SEAL- FRON
PartSelect #: PS2071511
Manufacturer #: 67730-1
  No Longer Available
SCREW – Part Number: 406062-1
SCREW
PartSelect #: PS2041704
Manufacturer #: 406062-1
  No Longer Available
SUB 12001344 – Part Number: 66403-1
SUB 12001344
PartSelect #: PS112340
Manufacturer #: 66403-1
  No Longer Available
CAP, CONNECTOR – Part Number: 68187-1
CAP, CONNECTOR
PartSelect #: PS115244
Manufacturer #: 68187-1
  No Longer Available
View More
Back to Top

Questions And Answers for HRNT15152A

We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.

Back to Top

Common Symptoms of the HRNT15152A

[Viewing 1 of 1]
Leaking
Fixed by
these parts
Fixing
Show All
Back to Top
Replacing the Ice Cube Tray

Replacing the Ice Cube Tray

View More
Back to Top
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
cocktails running out of ice
filled both ice cube trays up with water and placed in the freezer.. within hours my ice oproduction was doubled! no more warm cocktails : )
Parts Used:
Ice Cube Tray
  • Craig from Westminster, CA
  • Difficulty Level:
    Very Difficult
  • Total Repair Time:
    More than 2 hours
  • Tools:
    Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
56 of 61 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Icemaker fill tube cracked
The factory installed fill tube was formed and molded, hard plastic. Nothing like the replacement part or the one depicted in the install instructions.To remove it, I had to grip the exterior water tube module with a pair of Visegrip pliers, twist and pull as hard as possible, to expose a section of fill tube. I then had to cut through the tube with a hacksaw to remove the module and flange that secure it to the access hole. From the inside, I removed the ice maker and fan shield to expose the remaining section of fill tube. Using a section of copper pipe and a hammer, I was able to drive the tube through the back wall of the appliance. Fitting the new tube was easy. However, it is too short to reach the fill cup. I fashioned a section of the old tube to create an extension which I inserted in the new part. And, much to my surprise, it actually works!
Read less
Parts Used:
Icemaker Fill Tube
  • Mark from SEBASTOPOL, CA
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    1- 2 hours
  • Tools:
    Nutdriver, Pliers, Screw drivers, Socket set
5 of 5 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Replace broken ice cube trays
No repair needed. I had only to wash the new ones and use them.
Parts Used:
Ice Cube Tray
  • C MARTIN from TAMPA, FL
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
3 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
View More
Back to Top