Crosley Washer Dryer Combo Drums and Tubs

Videos!

Your Price

$24.95

Crosley Washer Dryer Combo Drum Glide (white)

★★★★★

16 Reviews

PartSelect Number PS5574052

Manufacturer Part Number 137513300

This white drum glide is used in a clothes dryer to ensure the front of the dryer drum is supported as it does rotations. *Please note: these are sold individually, however there are two of these in your appliance. We recommend that these be replaced at the same time, this allows for optimal performance and ensures they wear evenly. Each drum glide is approximately 33 inches in length. If the following symptoms occur, consider replacing the drum guide as a solution: dryer is noisy, will not tumble, or leaves marks on clothes. Remember to unplug the power source to the dryer before installing this part. Refer to the diagram provided by the manufacturer for further instructions and guidance.

Fixes these symptoms

Marks left on clothes
Noisy
See more...

Installation Instructions

Sergio from Cromwell, CT

Clothes were getting caught in gap, leaving burn mark.

Took the face off, and replaced the worn down drum glide and felt. Works just fine now. Read more...

Videos!

Your Price

$54.40

Crosley Washer Dryer Combo Drum Vane

★★★★★

2 Reviews

PartSelect Number PS417359

Manufacturer Part Number 131274600

Also known as a Drum Baffle. Sold individually.

Fixes these symptoms

Marks left on clothes
See more...

Installation Instructions

Eugene from Westbrook, ME

broken drum vane needed replacing

Front-loading Frigidaire washer made by Electrolux:
I removed the one phillips screw that secures the drum, but found the vane did not slide toward the front as I'd read it should. Nor was I able to squeeze the base to release it. I ended up using a rubber mallet and screwdriver to spring the snaps at the bottom of the vane. Once I had two of these on the same side out, I was able to slide the vane forward and remove it. Turns out there was a metal tab, part of the drum, bent into the vane so it couldn't slide for removal. I bent this tab down even with the drum surface, and the new vane slid in easily. Read more...

Your Price

$52.42

Crosley Washer Dryer Combo Drum Baffle

PartSelect Number PS8689126

Manufacturer Part Number 137552900

This part moves the clothes around inside your dryer and helps to direct the flow of hot during the drying cycle.

Installation Instructions

Alfred from Loveland, CO

Old Dryer drum veins degraded and broke down.

I opened the top of the dryer to gain access to the outside of the drum. Then I removed the screws holding the old drum veins in using the electric drill with the nut driver attachment. Then I positioned the new veins in place on the inside of the drum and replaced the screws from the outside of the drum to hold the veins in place. Then I replaced the top and was ready to go.

This is the third repair that I have done using parts from parts select. the other two repairs involved replacing electrical parts. Specifically thermostatic controls or swicthes. I am very happy with the parts and the diagrams provided on your web site without wich I would have had to replace my dryer a long time ago. Read more...

Your Price

$74.79

Crosley Washer Dryer Combo Ring Balance

★★★★★

2 Reviews

PartSelect Number PS11741965

Manufacturer Part Number WP387240

Installation Instructions

James from Asheville, NC

Washing machine shakes violently during spin cycle

Removed four screws that hold the top control panel to the base and hung over the back panel in order to remove the main wrap-around body of the machine. Took off top plastic ring fastened to side of tub then removed old Balance ring. Installed new balance ring. Unfortunately, this did NOT fix the problem. This was a suggestion from Justanswer.com and failed miserably. Does anybody know how to fix this problem? And it's not the springs or the little plastic shims around the base OR the cross coupling to the motor... Read more...

Your Price

$95.98

Crosley Washer Dryer Combo Trunnion

PartSelect Number PS418105

Manufacturer Part Number 131545101

This part helps with the spinning and agitating cycles.

Fixes these symptoms

Leaking
See more...

Installation Instructions

Rick from Walkerton, IN

The primary problem was that the tub seal assembly was leaking.

1. I began by removing the two screws that hold the front panel in place. I then lifted the top free of the front panel and tilted it back to get it out of the way.

2. Using my fingers, I released the tabs that connect the tub cover to the tub. It took some effort to remove the cap("Mechanism") over the bolt connecting the agitator to the agitator drive block because I didn't want to break the tab. Once removed, I removed the bolt and the agitator. I then removed the two bolts that clamp the Trunnion to the agitator shaft.

3. It took a little more effort to remove the tub because of corrosion, however, by rocking the tub back and forth I was able to work it free and remove it. I then removed the bolts connecting the Trunnion to the tub. It took a hammer to remove the Trunnion from the tub, once again because of corrosion.

4. After removing the tub, the seal assembly was next and it was easy to remove. I cleaned the agitator shaft with steel wool before beginning the reassembly to remove the corrosion. Before installing the new seal, I lubricated the agitator shaft and the inside of the seal with a silicone grease that is normally used for water faucets. The seal installed easily although care was required to insure that the seal did not twist out of place when sliding it down the agitator shaft.

5. The rest of the reassembly went easily. Since my old filter on the bottom of the tub was clogged, I replaced it with a new one. It took a little time to get every tab on the filter aligned properly so that it could be rotated into place, but it went easily. Everything else reassembled with no problems.

6. It took considerable time to figure out how to replace the drive belt idler arm assembly because I could not figure out how to remove the pin that the idler arm pivots on. I finally reviewed the parts list on-line again and determined that there is a small C-clip that holds it together. Once I knew that. I was able to see the clip and remove it. From that point on, it was very easy to remove the old assembly and reinstall the new one. If I had to do it over again, I would have changed the sleeve at the same time that I changed the idler assembly because the assembly still wobbles on the pin more than I would like. However, it works fine so I won't worry about it until other repairs are needed.

The parts that I ordered from Parts Select were exact matches for the parts that I removed. They were in stock and were shipped the next business day. I would rate the repair as very easy. Read more...

Your Price

$88.32

Crosley Washer Dryer Combo Washer Ringtub

★★★★★

1 Review

PartSelect Number PS11765521

Manufacturer Part Number W10880720

Introduce your washer to the Whirlpool's top-notch Tub Ring. A genuine OEM part, this tub ring is compatible with certain models of several popular brands including Whirlpool, KitchenAid, Maytag, Jenn-Air, Amana, Inglis, and Magic Chef. This tub ring clicks perfectly over the top of your washer's tub serving as a solid splash shield. Although the assembly might comprise multiple components, please reference the parts diagram for a detailed segment list. Remember, wearing work gloves during installation can help protect your hands. Trust Whirlpool's Tub Ring for a clean, leak-free laundry experience at home.