General Electric Microwave Electronics
- Search your model number to find:
- Genuine OEM parts guaranteed to fit
- Free manuals and guides
- Repair instructions and videos
Popular General Electric Microwave Electronics
Your Price
$16.95
In Stock
General Electric Microwave Cable Assembly
PartSelect Number PS16219547
Manufacturer Part Number WB27X35382
This part is the replacement high-voltage diode for your microwave. It is approximately 3 inches long and is sold individually. The high voltage diode is an electrical current control device inside your microwave. Be sure to disconnect power to the microwave, and use extreme caution when completing this repair, as microwaves can still retain an electrical charge even when unplugged. This part is an authentic OEM part sourced directly from the manufacturer.
Fixes these symptoms
- No heat
- See more...
Installation Instructions
Gregg from Santa Ana, CA
Microwave made loud buzz noise and did not heat
I followed the generic trouble shooting directions on the web site. It suggested either diode, capacitor and/or magnetron. I test each. All tested OK except diode. It was supposed to measure open in one direction and appox 200k ohms in the other direction. My diode measured open in both directions (tried multiple times, multiple settings). I replaced the diode. The order process was great and it shipped immediately. I knew I was in trouble when I measured the new diode and it too was open in both directions. It was easy to install but unfortunately no joy - did not solve the problem. At this point it is likely cheaper just to buy a new one
Read more...
Your Price
$229.95
In Stock
General Electric Microwave Magnetron
PartSelect Number PS12722595
Manufacturer Part Number WB26X32629
Genuine OEM magnetron for your microwave. Always use proper safety equipment and follow the manufacturers instructions while installing.
Fixes these symptoms
- No heat
- See more...
Installation Instructions
Michael from Coulterville, CA
No power to microwave, no heating.
Unpluged power cord!! Removed front control panel to expose electronics (need to remove top horizontal vent cover to expose mounting hardware). Unplugged leads to control panel board. Removed magnetron with Tstat (3- phillip heads, need stubby). Installed new parts and control panel, plugged it in tested. Done.
Read more...
Your Price
$251.92
In Stock
General Electric Microwave Digitron
Step one: Disconnect the power to the Advantium 120. Unplug unit, trip the breaker, whatever. Your responsibility to make sure the electrical power is removed.
For cabinet mounted units remove four screws from front side flange holding the microwave to cabinet
On the cabinet mounted model access three screws along the top front edge of case behind the display then one screw on each side of display and two hidden screws accessed through the top of the case via access holes. (use a magnetic see driver for these screws)
Work the display panel off and support it until the connectors are removed.
There are three small color coded plugs on the left side to the PC board and five larger colored plugs on the right side. Note plug locations.
Lay the removed control panel upside down on a towel at the corner of the sink so the selector knob is not resting on the counter.
Remove PC plug to the display and remove four screws on the PC board. Shift the PC board to release the tabs. Then remove two screws holding the PC display board. Note two guide pins also align the PC board.
Remove the rubber insulator from the old board and put it at the same location on the new board. There is usually enough stickiness on this insulator to put it back on the new board.
Installation is reverse. Reconnect power. Try it out after completion by boiling water in a microwave safe container. My new display was much brighter than the replaced display. No flashing. Read more...
PartSelect Number PS1018741
Manufacturer Part Number WB27X10856
Introducing the Digitron Display Board, a crucial component for your GE microwave. This display board showcases the selected operation cycle effectively and provides seamless utility. Please be advised, due to the high-voltage capacitors within the microwave with the potential to hold a deadly electrical charge even when it's unplugged, we recommend having a service technician execute the installation of this part. Trust in the reliability and performance of this exceptional GE component for your microwave refurbishment needs. Upgrade the performance of your appliance with this precision-engineered GE part. Trust in GE?s commitment to providing parts that are crafted for optimal performance and longevity.
Fixes these symptoms
- Touchpad does not respond
- See more...
Installation Instructions
William from EAGLE, ID
Flashing display
Replace Advantium 120 flashing display.Step one: Disconnect the power to the Advantium 120. Unplug unit, trip the breaker, whatever. Your responsibility to make sure the electrical power is removed.
For cabinet mounted units remove four screws from front side flange holding the microwave to cabinet
On the cabinet mounted model access three screws along the top front edge of case behind the display then one screw on each side of display and two hidden screws accessed through the top of the case via access holes. (use a magnetic see driver for these screws)
Work the display panel off and support it until the connectors are removed.
There are three small color coded plugs on the left side to the PC board and five larger colored plugs on the right side. Note plug locations.
Lay the removed control panel upside down on a towel at the corner of the sink so the selector knob is not resting on the counter.
Remove PC plug to the display and remove four screws on the PC board. Shift the PC board to release the tabs. Then remove two screws holding the PC display board. Note two guide pins also align the PC board.
Remove the rubber insulator from the old board and put it at the same location on the new board. There is usually enough stickiness on this insulator to put it back on the new board.
Installation is reverse. Reconnect power. Try it out after completion by boiling water in a microwave safe container. My new display was much brighter than the replaced display. No flashing. Read more...
Your Price
$41.95
In Stock
General Electric Microwave Diode Cable
The GE Advantium was another story. Replaced the Magnetron, diode, and capacitor. Oven still did not work so I took it to the dump. No more GE! Read more...
PartSelect Number PS239148
Manufacturer Part Number WB27X10037
Fixes these symptoms
- No heat
- See more...
Installation Instructions
Christopher from Chruchville, MD
Dishwasher would not pump water out. Othre appliance was advantium oven.
Removed the dishwasher. Simple to remove and replace the pump, flapper, and o-ring. Reinstalled dishwasher. It worked!The GE Advantium was another story. Replaced the Magnetron, diode, and capacitor. Oven still did not work so I took it to the dump. No more GE! Read more...
Your Price
$15.95
In Stock
General Electric Microwave Diode Cable Assembly
PartSelect Number PS3529603
Manufacturer Part Number 6851W1A002E
Usually found kitchen appliances, this OEM-certified diode cable assembly helps to convert power from the transformer to the magnetron, to heat up your food. A damaged cable assembly will cause your appliance to heat food inconsistently or to not work at all. You might notice a burning smell or a loud buzzing sound coming from your appliance. If you do not replace a broken cable assembly, the components that produce heat in your appliance can overheat and fail. To replace your cable assembly, start by unplugging your appliance from any electrical source. Remove any protective casing from the assembly by unthreading any screws or clips. Disconnect the cable assembly from the transformer and the magnetron with pliers. Reinstalling a new cable assembly requires you to reverse the previous steps. Please keep in mind that this cable assembly is sold individually.
Fixes these symptoms
- No heat
- See more...
Your Price
$129.10
In Stock
General Electric Microwave Magnetron
1. Unplug device.
2. Two people to remove from wall/cabinet (remove two, large, top mounting screws and rotate entire microwave down and off the wall mount). Should be some wood spacers between top of device and bottom of cabinet.
3. Remove screws from sheet metal cover.
4. Remove one screw holding blowers in place and rotate out of the way, in order to gain access to 2 of 5 screws that hold the magnetron in place.
5. Unplug magnetron and remove the 5 screws.
6. Drop in new magnetron and re-assemble microwave in reverse order (steps 5-3).
7. Two people restore micro to wall/cabinet. Replace wood spacers, re-install two, large mounting screws (finger-tight). Test device. Secure the two large screws. Read more...
PartSelect Number PS3529034
Manufacturer Part Number 6324W1A001L
This magnetron in your microwave creates the radiation needed for cooking or warming your food. It is located inside the main cavity, typically near the transformer or waveguide. When the magnetron becomes defective, your food may not heat up properly or heat up at all. Additionally, buzzing or humming sounds may be noticeable while the microwave is in operation. With a malfunctioning magnetron, your microwave loses its primary function. To remove it, you first need to unplug your microwave from its outlet. Before touching any components, discharge the capacitor by placing a screwdriver, with an insulated handle, across the two terminals of the capacitor. Once the capacitor is discharged, replace the current magnetron by disconnecting it from any wires and removing any mounting screws or clips. This magnetron is sold individually and is supplied directly from the original equipment manufacturer.
Fixes these symptoms
- No heat
- See more...
Installation Instructions
Joseph from WILTON, NH
Magnitron failed
Over the stove microwave installed in top cabinet row.1. Unplug device.
2. Two people to remove from wall/cabinet (remove two, large, top mounting screws and rotate entire microwave down and off the wall mount). Should be some wood spacers between top of device and bottom of cabinet.
3. Remove screws from sheet metal cover.
4. Remove one screw holding blowers in place and rotate out of the way, in order to gain access to 2 of 5 screws that hold the magnetron in place.
5. Unplug magnetron and remove the 5 screws.
6. Drop in new magnetron and re-assemble microwave in reverse order (steps 5-3).
7. Two people restore micro to wall/cabinet. Replace wood spacers, re-install two, large mounting screws (finger-tight). Test device. Secure the two large screws. Read more...
Your Price
$49.95
In Stock
General Electric Microwave Capacitor
PartSelect Number PS2353613
Manufacturer Part Number WB27X11033
Fixes these symptoms
- No heat
- See more...
Installation Instructions
bart from new sarpy, LA
Try to heat food and fuse would blow.
Went on Youtube and pulled up how to fix a microwave.
Read more...
Your Price
$56.38
In Stock
General Electric Microwave Diode
PartSelect Number PS239740
Manufacturer Part Number WB27X10597
This part allows power to go one way only.
Fixes these symptoms
- No heat
- See more...
Installation Instructions
Theodore from Medical Lake, WA
Not working as far as heating or cooking
Replaced High Voltage Diode. Very carfully due to the extream danger of a electrical shock.
Read more...
Your Price
$115.38
In Stock
General Electric Microwave Magnetron
PartSelect Number PS16873479
Manufacturer Part Number WB27X44106
This part is used to generate microwave energy/heat.
Fixes these symptoms
- No heat
- See more...
Installation Instructions
Sal from Center Moriches, NY
Micro was not producing heat.
Removed unit from above range. (A two person task.) Removed display panel, disconnecting wires from plugins. Removed outer cover to access magnetron. Used camera to take photos before disconnecting other wires. Replaced magnetron and reconnected wires, double checking with photo. Tested prior to reinstalling. It works fine.
Read more...
Your Price
$243.48
In Stock
General Electric Microwave Magnetron
PartSelect Number PS239377
Manufacturer Part Number WB27X10249
This part is used to generate microwave energy/heat.
Related General Electric Microwave Parts
- All General Electric Microwave parts
- General Electric Microwave Brackets and Flanges
- General Electric Microwave Caps and Lids
- General Electric Microwave Circuit Boards and Touch Pads
- General Electric Microwave Doors
- General Electric Microwave Drawers and Glides
- General Electric Microwave Ducts and Vents
- General Electric Microwave Elements and Burners
- General Electric Microwave Fans and Blowers
- General Electric Microwave Filters
- General Electric Microwave Fuses
- General Electric Microwave Glass Tray and Supports
- General Electric Microwave Grilles and Kickplates
- General Electric Microwave Handles
- General Electric Microwave Handles and Latches
- General Electric Microwave Hardware
- General Electric Microwave Hinges
- General Electric Microwave Insulations
- General Electric Microwave Knobs
- General Electric Microwave Latches
- General Electric Microwave Legs and Feet
- General Electric Microwave Lights and Bulbs
- General Electric Microwave Motors
- General Electric Microwave Panels
- General Electric Microwave Power Cords
- General Electric Microwave Racks
- General Electric Microwave Seals and Gaskets
- General Electric Microwave Sensors
- General Electric Microwave Springs and Shock Absorbers
- General Electric Microwave Switches
- General Electric Microwave Thermostats
- General Electric Microwave Transformers
- General Electric Microwave Trays and Shelves
- General Electric Microwave Trims
- General Electric Microwave Wheels and Rollers
- General Electric Microwave Wire Plugs and Connectors