Jenn-Air Washer Dryer Combo Seals and Gaskets

Find Your Part

Model number locator Need help finding your model number?
  • Search your model number to find:
  • Genuine OEM parts guaranteed to fit
  • Free manuals and guides
  • Repair instructions and videos
Jenn-Air Appliance Parts
Shop By Part Type

Popular Jenn-Air Washer Dryer Combo Seals and Gaskets

Videos!
Your Price
$29.00
  In Stock
Jenn-Air Washer Dryer Combo Front or Rear Drum Felt Seal
★★★★★
★★★★★
2 Reviews
PartSelect Number PS11740771
Manufacturer Part Number WP314820
This front or rear dryer drum felt seal is seventy-nine and a half inches long.
Fixes these symptoms
Installation Instructions
John from Charlottesville, VA
Belt broke on old machine.
1. Removed front of machine (2 screws at the bottom).
2. Removed 4 screws from inside the dryer, to take off the blower housing.
3. Removed 4 screws and took out the large metal piece which supports the drum at the front. Removed the drum.
4. Replaced the two rollers that support the drum in the rear. Cleaned the pins they run on, and oiled very lightly. Also replaced the idler roller. I was surpirsed to see that these rollers use plain bearings, not ball bearings.
5. On the front support piece, drilled out the rivets for the glides, and replaced the worn out glides with new parts. Applied a little glue (3M weatherstrip adhesive) to the cork pieces, to glue them to the metal. Attached the plastic pieces over the cork pieces, and riveted in place using rivets that came with the glide kits.
6. Replaced front and rear felt seals. This was not as tricky as I expected it to be. They were held in by metal tabs. Glued the ends where they came together.
7. Replaced the felt blower seal. Glued to the blower housing.
8. Reinstalled the drum, installed new belt, which came with good instructions (luckily).
9. Reassembled front support piece and the front of the cabinet.

I also cleaned the lint from the cabinet and from the vent hose.

In general, the job went without a hitch, and the machine probably has quite a few years left, despite the fact that it's 18 years old. This gives me a good feeling.

I'd say this would be challenging, though, for someone who is not pretty experienced with machinery repair. Also, the cost of the parts was significant enough that it would not have been unreasonable to have opted for a new machine. Read more...
Your Price
$7.60
  In Stock
Jenn-Air Washer Dryer Combo Hose Washer and Screen Insert Kit
PartSelect Number PS2003023
Manufacturer Part Number 12001413
The hose washer in this washer and screen insert kit is an inch in diameter. The insert is all blue in color and is made entirely of plastic, while the washer is all black in color and made entirely of rubber.
Fixes these symptoms
Installation Instructions
Daniel from Severn, MD
No cold water
Doing this repair was a breeze. After disconnecting the power and water I popped the lid and it was 3 screws and 2 wire connectors. Reassembled and done. This was beyond cost effective to do and with simple look see at a diagram anyone with basic mechanical know how and some basic tools could do this. Read more...
Your Price
$49.71
  In Stock
Jenn-Air Washer Dryer Combo Tub Gasket
★★★★★
★★★★★
2 Reviews
PartSelect Number PS11739260
Manufacturer Part Number WP22001007
Fixes these symptoms
Installation Instructions
Donald from GROSSE PT PK, MI
Tub gasket leaking because of age.
Top came off quickly with socket wrench. Removed gasket in about a minute. Spent 45 minutes getting grime ( soap and lime) off of top. Took five minutes to replace gasket.

Haven't been able to get front back on. Clips go on side rather than top. Found missing clip for which new one was purchased in transmission. Still haven't gotten front to stay on. Clips keep springing out. Read more...
Your Price
$43.39
  In Stock
Jenn-Air Washer Dryer Combo Outer Tub Clamp Seal
★★★★★
★★★★★
1 Review
PartSelect Number PS11738869
Manufacturer Part Number WP211232
This outer tub clamp seal is sixty-eight inches long. It is black and made of rubber.
Fixes these symptoms
Installation Instructions
George from Fort Myers Beach, FL
Clamp rusted through permitting upper & lower tub to separate
Clamp was already in multiple pieces so easy to get off.

Got clamp from partselect.com in 1 day which was great.

Removed two PH screws from front cover then pulled bottom of front cover outward and down to remove.

Caution for those doing this: take a piece of 220 or 240 grit paper and sand all the edges of the clamp. Trying to put it on without doing so will result in countless paper cuts in hands.

Before putting new clamp on be sure to use either some soap or silicon lube on the rubber V seal between upper and lover tub.

Also need to put some 1/4" to 3/8" spacers at three equally spaced places beneath the upper tub and the lower tub. If this isn't done the upper tub will drop down too far inside the lower tub and the inner lower tub, when it starts to spin, will rub on the underside of the upper tub = cause the main drive belt to smoke and tub to "freeze up"

Spacers I used were simply 3 pieces of multi strand sheathed electrical wire 3/8" so that I could bend them down at an angle and put them out once clamp was in place. Wire pieces need to be about 4-5" long.

Assemble one bolt in clamp and thread around tub in CCW direction.

Position one bolt of the clamp in right rear corner. this is important so that when tub goes out of balance, there's clearance for the clamp bolts and they don't contact the cabinet.

Make sure before threading clamp arount tub that the screw that will end up in the front left corner has a hex head on it so that you can apply some clamping "muscle" with a socket wrench.

I had trouble getting the front left screw inserted in the clamp (its only 2" long) so I used a 3" bolt to make the preliminary connection to pull the clamp semi tight. I planned ahead and got a light wire coat hanger to use as a "tie-tie" in the event that I had to remove the 3" slotted screw to revert back to the 2" hex head screw. Luckily when I removed the 3" screw I was able to quickly pop the 2" hex head back in and tighten completely.

Before putting front cover on, do one load with front cover off to make sure that upper and lower/inner tub don't rub each other.

If ok, turn power back off and put front cover back on.

Note: Would advised ordering the rubber V-seal if you are ordreing the clamp. If you buy the seal there are four bolts in the lid that let you lift the lid to work on the tub, clamp and seal MUCH more easily. Sticky part is getting water fill tube in top left rear disconnected so that new rubber v-seal can slide over tub.

Note also that in order to get to front left lid bolt that single bolt holding diaphram onto front left upright must be removed so as the let diaphram assembly drop away to access front left lid bolt. The two bolts in the rear can be accessed from the top very easily. Also need to disconnect the bleach fill tube in order to lift the lid (right side lifts up to vertical position) Read more...
Your Price
$9.78
  In Stock
Jenn-Air Washer Dryer Combo Injector Tube Seal
★★★★★
★★★★★
1 Review
PartSelect Number PS11738906
Manufacturer Part Number WP215233
This injector tube seal is just over an inch in diameter. It is black in color and made of rubber.
Fixes these symptoms
Installation Instructions
Catherine from Wyandotte, MI
Front load washing machine leaking on floor while in fill mode.
Removed two screws at bottom of front panel and then removed front panel. Then removed two self-tapping bolts (one on each side) holding top panel in place and swung the panel up, out of the way, to expose top of tub and water injection components. Cut off one pinch clamp and loosened screw clamp holding two injector hoses to the injector sleeve. Removed these water injector hoses from injector sleeve assembly which is mounted on top of left side panel upper flange. Replaced deteriorated rubber injector valve, nozzle and the sleeve for the injector (plastic housing containing the injector valve and nozzle). Also replaced deteriorated injector tube seal where injector tube elbow mounts to top of tub assembly. Reinstalled injector hoses with a replacement screw clamp to replace the one cut off. tightened the new clamp and the other, original, screw clamp and checked for leaks. This solved the leakage problem. Secured top panel and re-installed front panel. Hardest part of the task was determining where the leak emanated from but once found and parts ordered, it was a relative snap to fix. Read more...
Your Price
$52.22
  In Stock
Jenn-Air Washer Dryer Combo Dryer Blower Housing Seal
PartSelect Number PS11757541
Manufacturer Part Number WPY312901
The blower housing seal makes an airtight seal between the blower housing and the blower housing cover in the dryer.
Fixes these symptoms
Installation Instructions
John from Charlottesville, VA
Belt broke on old machine.
1. Removed front of machine (2 screws at the bottom).
2. Removed 4 screws from inside the dryer, to take off the blower housing.
3. Removed 4 screws and took out the large metal piece which supports the drum at the front. Removed the drum.
4. Replaced the two rollers that support the drum in the rear. Cleaned the pins they run on, and oiled very lightly. Also replaced the idler roller. I was surpirsed to see that these rollers use plain bearings, not ball bearings.
5. On the front support piece, drilled out the rivets for the glides, and replaced the worn out glides with new parts. Applied a little glue (3M weatherstrip adhesive) to the cork pieces, to glue them to the metal. Attached the plastic pieces over the cork pieces, and riveted in place using rivets that came with the glide kits.
6. Replaced front and rear felt seals. This was not as tricky as I expected it to be. They were held in by metal tabs. Glued the ends where they came together.
7. Replaced the felt blower seal. Glued to the blower housing.
8. Reinstalled the drum, installed new belt, which came with good instructions (luckily).
9. Reassembled front support piece and the front of the cabinet.

I also cleaned the lint from the cabinet and from the vent hose.

In general, the job went without a hitch, and the machine probably has quite a few years left, despite the fact that it's 18 years old. This gives me a good feeling.

I'd say this would be challenging, though, for someone who is not pretty experienced with machinery repair. Also, the cost of the parts was significant enough that it would not have been unreasonable to have opted for a new machine. Read more...
Your Price
$8.02
  In Stock
Jenn-Air Washer Dryer Combo Inlet Hose Washer
★★★★★
★★★★★
1 Review
PartSelect Number PS11757437
Manufacturer Part Number WPY013783
This inlet hose washer, also known as a high pressure inlet hose washer, is used in washing machines, refrigerators, freezers, and dishwashers. The function of this part is to create a watertight seal in the appliance. If your gasket gets dry and brittle over time it will start to crack and will lose its function. In this case, it is important to replace it. Refer to the manual provided by the manufacturer for further installation instructions and accurate guidance. As a safety precaution, remember to unplug your washer from the power source before beginning.
Fixes these symptoms
Installation Instructions
Roger from Lore City, OH
(Portable ) The Hose Hook up from the dishwasher to the kitchen faucet would not seal. After replacing the hoses the connection hoses sealede.
tilted the dishwasher back so the bottom was exposed and unhooked the old hoses, then removed old hoses through the back side of the dish washer then fed the new hoses through the back and hooked them up. Read more...
Your Price
$52.52
  In Stock
Jenn-Air Washer Dryer Combo Syphon Break Gasket
PartSelect Number PS11738895
Manufacturer Part Number WP214765
This syphon break gasket is just over an inch in diameter. It is black in color and made of rubber.
Fixes these symptoms
Installation Instructions
Jeff from Moorpark, CA
Water leak noted on floor at front of washer and at sides
Occasional noted leak became worse and I had a repair service out. Incorrect detection of outer tub seal made so cancelled them and read comments about raising the top. Did so just at start of a rinse cycle to see soapy water shoot from top of syphon break then continue to dribble out through tub empty process--this is what had cause the water to flow down the interior drain hose and out through the side and bottom near the pump.

Ordered all the parts shown here and they arrived just in time for planned work. Did not need or use the clamp and gasket purchased as the gasket was included in the break package and I really like the old-style clamps much better.

Replaced the break and the elbow and put it back together. Things went south on a rinse as water shot out the back hose at the new elbow. I had not realized the size of the new elbow was smaller than the original. Went back to the old elbow but it bothered me that it would still move when the 4 assembly bolt-screws were completely tight.

So far this seems to have worked. There does not seem to be any leaking at all. For those who read this, the job could be done in about and hour for less than I spent if you observe and diagnose properly. It appears that the washer at the end of the Syphon Break wore out and that is what caused the leak.

Thanks much to PartSelect for being in business and to all the posters on this site for helping everyone to get these things done right! Read more...
Your Price
$133.76
  In Stock
Jenn-Air Washer Dryer Combo Tub Cover with Gasket
★★★★★
★★★★★
2 Reviews
PartSelect Number PS2019504
Manufacturer Part Number 22001299
May not be exactly as shown.
Fixes these symptoms
Installation Instructions
William from Ambler, PA
Tub Cover Split And Leaking
Removed washing machine front cover (2 phillips screws on bottom half of panel). Then removed two bolts that hold the top in place. Lifted hinged top, removed tub cover which is held in place with plastic mounting tabs. That was it. Put everthing back together approx. 15 Minutes. Read more...

Related Jenn-Air Washer Dryer Combo Parts

Back to Top