KitchenAid Microwave Circuit Boards and Touch Pads
- Search your model number to find:
- Genuine OEM parts guaranteed to fit
- Free manuals and guides
- Repair instructions and videos
Popular KitchenAid Microwave Circuit Boards and Touch Pads
Your Price
$196.00
On Order
KitchenAid Microwave Inverter
PartSelect Number PS2342258
Manufacturer Part Number W10217711
The inverter acts like the brain for the microwave. It sends high voltage to the magnetron to produce heat.
Fixes these symptoms
- No heat
- See more...
Your Price
$276.61
In Stock
KitchenAid Microwave Electric Control Board
PartSelect Number PS12348595
Manufacturer Part Number W11179310
Experience the ideal solution for your Whirlpool wall oven with our state-of-the-art electronic control board. This genuine OEM Whirlpool part is designed to flawlessly manage all oven functions, including adjusting temperatures and controlling heating. Highly compatible, it works with select models of renowned brands like Whirlpool, KitchenAid, Maytag, Jenn-Air, Amana, Inglis, and Magic Chef. Be certain to make correct oven model verification before placing an order. Installation is simple but please ensure power safety measures are adhered to halting the house circuit or unplugging the oven and don the proper safety gear. The efficient design of this control board guarantees a seamless fit and an optimal performance.
Your Price
$120.23
In Stock
KitchenAid Microwave Led Display Board
2) Removed the four screws holding the extension kit to the microwave (easily visible on the front of the microwave) and removed the side panels (required sliding the panels up and off).
3) Removed the six screws holding the microwave to the cabinet (exposed after removing the extension kit)
4) Slide the microwave out and unplugged the cord from the outlet
5) Removed the screws that secured the front display panel to the microwave. These are located on the side of the microwave just behind the display panel. There are a total of 4 screws, 2 on each side. Additionally there was a clip holding the front panel on. We were able to press down to get it to release. NOTE: You will not be able to fully remove the panel as there are cables that run back to the board which is only reachable by removing the top panel
6) Removed the screws along the sides. back, and top to remove the top panel (there are 3 screws on each side and 2-3 in the back, there is only one screw on the top near the back right that holds the top to a part inside the microwave.
7) Peeled the top off of the microwave - there is a line of double sided tape that held the front of the top panel to the back of piece where the front display panel was mounted.
8) Carefully remove the existing LED Display Board. There is a single plastic clip that you have to very gently press back to slide the LED out. We were not careful enough and the clip broke. It did not hinder the replacement and even without the small plastic bit the LED board sat snuggly in its spot.
9) Trace the cable from the LED board back to the circuit board and unplug the cable. We pulled the cable out through the front of the microwave as the hole from the front display panel back to the board was just slightly too small to fit the board through.
10) The new LED panel arrived with extra boards attached to it. There were clear spots where the boards were perforated to easily snap off.
11) Thread the new cable from the front of the microwave through the hole and plug in where you removed the previous cable
12) Seat the LED Display Board in the slot.
13) Replace the top of the microwave and the associated screws (we used four small bowls to separate the screws for the top of the microwave, screws for the front of the microwave, screws for mounting the microwave, and screws for the expansion kit)
14) Reseat the front panel and replace screws
15) Plug microwave back in. (We took this opportunity to turn the breaker back on to test and make sure everything was working before we remounted the microwave)
16) Place microwave back in its mount and secure with mounting screws
17) Replace the extension kit if applicable and its associated screws. Read more...
PartSelect Number PS11748663
Manufacturer Part Number WPW10124269
Installation Instructions
Krystal from YORK, PA
The LED display on the microwave was no longer functional. Some lights still showed, but not enough to be able to tell the time or validate timer settings.
1) Identified the breaker that the microwave was connected to and turned it off.2) Removed the four screws holding the extension kit to the microwave (easily visible on the front of the microwave) and removed the side panels (required sliding the panels up and off).
3) Removed the six screws holding the microwave to the cabinet (exposed after removing the extension kit)
4) Slide the microwave out and unplugged the cord from the outlet
5) Removed the screws that secured the front display panel to the microwave. These are located on the side of the microwave just behind the display panel. There are a total of 4 screws, 2 on each side. Additionally there was a clip holding the front panel on. We were able to press down to get it to release. NOTE: You will not be able to fully remove the panel as there are cables that run back to the board which is only reachable by removing the top panel
6) Removed the screws along the sides. back, and top to remove the top panel (there are 3 screws on each side and 2-3 in the back, there is only one screw on the top near the back right that holds the top to a part inside the microwave.
7) Peeled the top off of the microwave - there is a line of double sided tape that held the front of the top panel to the back of piece where the front display panel was mounted.
8) Carefully remove the existing LED Display Board. There is a single plastic clip that you have to very gently press back to slide the LED out. We were not careful enough and the clip broke. It did not hinder the replacement and even without the small plastic bit the LED board sat snuggly in its spot.
9) Trace the cable from the LED board back to the circuit board and unplug the cable. We pulled the cable out through the front of the microwave as the hole from the front display panel back to the board was just slightly too small to fit the board through.
10) The new LED panel arrived with extra boards attached to it. There were clear spots where the boards were perforated to easily snap off.
11) Thread the new cable from the front of the microwave through the hole and plug in where you removed the previous cable
12) Seat the LED Display Board in the slot.
13) Replace the top of the microwave and the associated screws (we used four small bowls to separate the screws for the top of the microwave, screws for the front of the microwave, screws for mounting the microwave, and screws for the expansion kit)
14) Reseat the front panel and replace screws
15) Plug microwave back in. (We took this opportunity to turn the breaker back on to test and make sure everything was working before we remounted the microwave)
16) Place microwave back in its mount and secure with mounting screws
17) Replace the extension kit if applicable and its associated screws. Read more...
Your Price
$146.83
In Stock
Your Price
$198.13
In Stock
KitchenAid Microwave Cntrl-elec
PartSelect Number PS11765745
Manufacturer Part Number W10891907
Enhance your Whirlpool wall oven performance with our user interface control board. This essential component is specifically designed for wall ovens, enabling you to accurately select the time and temperature settings. Prior to installation, ensure to shut off the house circuit breaker or disconnect the oven plug for safety precautions. To avoid injury during the process, we highly recommend wearing work gloves. Revel in the convenience of adjusted heat settings with this exclusive Whirlpool CNTRL-ELEC control board.
Your Price
$199.15
In Stock
KitchenAid Microwave Electric Control Board
PartSelect Number PS12069980
Manufacturer Part Number W10881539
Introducing the Whirlpool CNTRL-ELEC, a genuine OEM part meticulously designed to enhance your appliance's performance. This CNTRL-ELEC collaborates seamlessly with several models of Whirlpool, ensuring optimal functionality. Its primary function is to manage various microwave responsibilities, such as heating, lighting, and turntable operation. It is worth noting that due to the presence of high-voltage capacitors, installation of this part should be done by a service technician. A small variation in size and shape can occur, but rest assured, this does not compromise its efficacy and performance. Trust Whirlpool's CNTRL-ELEC for a reliable and efficient enhancement to your appliance.
Your Price
$210.67
In Stock
KitchenAid Microwave Electric Control Board
PartSelect Number PS12348634
Manufacturer Part Number W11182110
Your Price
$204.91
In Stock
KitchenAid Microwave Electric Control Board
PartSelect Number PS11751371
Manufacturer Part Number WPW10260060
Your Price
$26.95
In Stock
KitchenAid Microwave Noise Filter Board
PartSelect Number PS3500969
Manufacturer Part Number W10422269
The purpose of this board is to smooth out the voltage in the microwave into a more usable level.
Your Price
$132.70
In Stock
KitchenAid Microwave Electronic Control Board
PartSelect Number PS11748457
Manufacturer Part Number WPW10116267
Also known as the "brains" of your microwave.
Fixes these symptoms
- Touchpad does not respond
- See more...
Installation Instructions
Rae from Visalia, CA
I can't find instructions on how to remove the plastic inside of the door.
I removed all of the screws to take the plastic inside of the door off (except possibly 1 screw at top near the hinge). It seems the inside of the door should be loose, even IF there is another screw, but I can't get it to wiggle and I'm afraid I will break it.
Read more...
Related KitchenAid Microwave Parts
- All KitchenAid Microwave parts
- KitchenAid Microwave Brackets and Flanges
- KitchenAid Microwave Caps and Lids
- KitchenAid Microwave Doors
- KitchenAid Microwave Ducts and Vents
- KitchenAid Microwave Electronics
- KitchenAid Microwave Filters
- KitchenAid Microwave Fuses
- KitchenAid Microwave Glass Tray and Supports
- KitchenAid Microwave Handles
- KitchenAid Microwave Hardware
- KitchenAid Microwave Latches
- KitchenAid Microwave Lights and Bulbs
- KitchenAid Microwave Motors
- KitchenAid Microwave Panels
- KitchenAid Microwave Racks
- KitchenAid Microwave Seals and Gaskets
- KitchenAid Microwave Sensors
- KitchenAid Microwave Springs and Shock Absorbers
- KitchenAid Microwave Switches
- KitchenAid Microwave Transformers
- KitchenAid Microwave Trays and Shelves
- KitchenAid Microwave Trims
- KitchenAid Microwave Wire Plugs and Connectors