Magic Chef Dishwasher Pumps
- Search your model number to find:
- Genuine OEM parts guaranteed to fit
- Free manuals and guides
- Repair instructions and videos
Popular Magic Chef Dishwasher Pumps
Your Price
$59.95
In Stock
Magic Chef Dishwasher Drain Pump 120v 60hz
First remove the water from the dishwasher pan that would not drain with a wet/dry vac. Otherwise the water will all drain on the floor when you remove the pump. Then remove the two screws on the kickplate on the front of the unit below the door. Remove the kickplate/maintainence access cover. The drain pump is on the right about 8 inches in. Using two hands you grasp the drain pump with your right hand and use the left hand to push the retaining clip down. Then the drain pump will rotate 1/4 turn counterclockwise and can be removed without pulling the dishwasher out. There is likely to be some water leak out that was traped in the pump housing that you can not reach with the vac. Disconnect the wire. Connect the wire to the new pump, put it in place and 1/4 turn clockwise to install it. Replace the kickplate and you're done. Read more...
PartSelect Number PS11753379
Manufacturer Part Number WPW10348269
This drain pump is used in dishwashers to remove water from the dishwasher tub. If the impeller in the dishwasher is damaged or the motor has been shorted out and will not drain, it is possible the body is cracked, causing leakage. To prevent this from happening, replace the drain pump. The tools needed for this installation are: Phillips screwdriver, 5/16 inch nut driver, 5/8 inch wrench, and a flathead screwdriver. Remember to unplug your dishwasher from the power source before beginning this installation project. Refer to the manual provided by the manufacturer for further installation instructions.
Fixes these symptoms
- Leaking
- Noisy
- Not cleaning dishes properly
- See more...
Installation Instructions
Andrew from Alexandria, VA
dishwasher not draining after wash cycle
Caviat: The actual repair is less than 15 minutes, but I spent a lot of time playing with it before I figured out it was that easy and fast. You don't need to remove the dishwasher from the counter to do this. And it will probably help to look at the new part closely so you can understand where the retainer clip is to press it and release the old pump.First remove the water from the dishwasher pan that would not drain with a wet/dry vac. Otherwise the water will all drain on the floor when you remove the pump. Then remove the two screws on the kickplate on the front of the unit below the door. Remove the kickplate/maintainence access cover. The drain pump is on the right about 8 inches in. Using two hands you grasp the drain pump with your right hand and use the left hand to push the retaining clip down. Then the drain pump will rotate 1/4 turn counterclockwise and can be removed without pulling the dishwasher out. There is likely to be some water leak out that was traped in the pump housing that you can not reach with the vac. Disconnect the wire. Connect the wire to the new pump, put it in place and 1/4 turn clockwise to install it. Replace the kickplate and you're done. Read more...
Your Price
$33.95
In Stock
Magic Chef Dishwasher Chopper Assembly
PartSelect Number PS1734917
Manufacturer Part Number W10083957
This is a chopper assembly or drain food chopper, and it is designed for your dishwasher. The chopper chops up/minces the food particles in your dishwasher to prevent them from clogging the pump. You may need to replace this part if your dishes are not being cleaned properly, your appliance is particularly noisy, or you are noticing draining problems. The tools you will need to make this repair include a number 20 and a number 15 torque screwdriver, a small flat blade screwdriver, and a pair of needle nose pliers.
Fixes these symptoms
- Leaking
- Noisy
- Not cleaning dishes properly
- See more...
Installation Instructions
Steve from Killeen, TX
Not cleaning top tier,all dishes not getting clean
Disassembled inside bottom section of dishwasher found broken chopper part,removed and replaced with new part,only hard part was holding spring compressed when putting in new part,needed needlenose and thin screwdriver.Thank You for your great website and help
Read more...
Your Price
$94.62
In Stock
Magic Chef Dishwasher Impeller And Seal Kit
PartSelect Number PS12069388
Manufacturer Part Number 8193951A
This is the replacement impeller kit for your dishwasher. This impeller kit comes with 4 pieces, including the impeller and seals which you will need for the repair. The impeller and seal kit is mounted on the dishwasher motor. If your dishwasher is not cleaning dishes properly, it may be an indication that your impeller has gone bad, and you are not getting proper water pressure. If the seals have gone bad, your dishwasher may start to leak. If you are having either of these problems, you may need to replace the impeller kit. Be sure to disconnect the water and power source from the dishwasher before you begin this repair. This is an OEM part sourced directly from the manufacturer.
Fixes these symptoms
- Leaking
- Noisy
- Not cleaning dishes properly
- See more...
Installation Instructions
Chauncey from Menan, ID
Started with a grinding noise in the bottom of the dishwasher, and then the thing just stopped cleaning the dishes. It wasn't pumping any water,
I removed the plasic inner parts, used the torx drivers to remove the internal platic plate that covered the sump. Found the food chopper cover and removed it. It had gotten a piece of plastiic wrapped around it. As it spun it had ground the teeth off the end of the drive on the impellor and the food chopper. I replace both as a set and it works fine.
Read more...
Your Price
$46.13
In Stock
Magic Chef Dishwasher Wash Impeller
PartSelect Number PS11747701
Manufacturer Part Number WP99002659
This impeller rotates and is used to force water up through to the spray arm.
Fixes these symptoms
- Leaking
- Noisy
- Not cleaning dishes properly
- See more...
Installation Instructions
Timothy from Trevor, WI
Dishwasher would fill properly but when wash cycle would start you could not hear any water spraying.
First I removed the lower spray arm by removing the middle retainer nut. Next remove the 3 screws holding the outer shroud in place. Next remove 6 screws holding the water pump top housing in place. Under this housing you will find the impeller which is retained by a screw. Check the impeller closely for cracks especially near the center hex portion of the impeller. Replace if you have any doubt of it's integrity. Next remove the lower pump housing that has the screen material in the center. What I found was the nylon part that attaches to the shaft of the motor was stripped so the impeller would spin in it's normal direction ( counterclockwise) but under the load of water it would not. So I ordered a new impeller and seal kit with a metal sleeve and chooper blade. Follow the instructions provided in the new kit a reassemble accordingly.
Read more...
Your Price
$82.29
In Stock
Magic Chef Dishwasher Impeller
I don't think this could be done with the dishwasher in place, so I turned the water off to the unit and unplugged it. I had previously removed the front bottom cover plates (4 screws). I opened the front, removed the lower dish rack and unscrewed it from the bottom side of the counter, disconnected the water supply and drain line, then wiggled it out being careful of the insulation sheets, hoses, etc. Note, water drains everywhere. I had some baking pans to contain and paper towels to wipe but still, be safe / prepared.
I disconnected everything from the motor / impeller housing area, then went inside the unit and loosened the lock ring thing around the base of whatever you call the spinning arm / sprayer, it took a little effort, might be easier to try this when it is still mounted to the counter. After that main ring was removed the housing with the motor and everything just wiggled free.
I unscrewed the motor's 3 Torx screws, and then the unscrewed the plastic "X" at the end opposite the motor, the brass weight pulls straight off and the impeller is supposed to come off too. Mine was stuck like many I read about. I drilled a hole in the end of the plastic impeller and drove the motor shaft out with a punch and hammer, it worked pretty slick. Then I carefully pried out the last seal and stopped for a cold beverage, major success.
I carefully pushed the new seal into the housing, reattached the motor to the housing, pushed on the other new seals, the impeller, the new brass weight in the same order the old ones were, and screwed on the "X" on the end as snug as I could. Then I carefully reattached the motor and housing to the bottom of the dishwasher, ensuring good solid seals and tightening that big ring again from the inside as snug as I could get it, carefully hooked everything on the bottom back up basically in the reverse of disassembly, put the unit back under the counter, plugged it in, turned the water back on to it, loaded it and tested it. I was fortunate enough to not have it leak anywhere, after 3 or 4 loads I reattached the bottom trim pieces and checked this off my list.
Also, would love to mention that your site is great, the parts were priced attractively, they arrived very quickly and were a snap to install.
Thanks for saving me a ton of money / headaches!
Andy Read more...
PartSelect Number PS16542935
Manufacturer Part Number 4386996A
This kit contains Impeller and Bearing Assembly.
Fixes these symptoms
- Leaking
- Not cleaning dishes properly
- Not draining
- See more...
Installation Instructions
Andrew from Cottage Grove, MN
Dishwasher was leaking from bottom
After determining that the leak was coming basically from the motor shaft I googled until I thought I could handle it, took it apart to confirm I could get it apart (I thought it might be too stuck and I might need the whole motor thing) and then ordered the kit.I don't think this could be done with the dishwasher in place, so I turned the water off to the unit and unplugged it. I had previously removed the front bottom cover plates (4 screws). I opened the front, removed the lower dish rack and unscrewed it from the bottom side of the counter, disconnected the water supply and drain line, then wiggled it out being careful of the insulation sheets, hoses, etc. Note, water drains everywhere. I had some baking pans to contain and paper towels to wipe but still, be safe / prepared.
I disconnected everything from the motor / impeller housing area, then went inside the unit and loosened the lock ring thing around the base of whatever you call the spinning arm / sprayer, it took a little effort, might be easier to try this when it is still mounted to the counter. After that main ring was removed the housing with the motor and everything just wiggled free.
I unscrewed the motor's 3 Torx screws, and then the unscrewed the plastic "X" at the end opposite the motor, the brass weight pulls straight off and the impeller is supposed to come off too. Mine was stuck like many I read about. I drilled a hole in the end of the plastic impeller and drove the motor shaft out with a punch and hammer, it worked pretty slick. Then I carefully pried out the last seal and stopped for a cold beverage, major success.
I carefully pushed the new seal into the housing, reattached the motor to the housing, pushed on the other new seals, the impeller, the new brass weight in the same order the old ones were, and screwed on the "X" on the end as snug as I could. Then I carefully reattached the motor and housing to the bottom of the dishwasher, ensuring good solid seals and tightening that big ring again from the inside as snug as I could get it, carefully hooked everything on the bottom back up basically in the reverse of disassembly, put the unit back under the counter, plugged it in, turned the water back on to it, loaded it and tested it. I was fortunate enough to not have it leak anywhere, after 3 or 4 loads I reattached the bottom trim pieces and checked this off my list.
Also, would love to mention that your site is great, the parts were priced attractively, they arrived very quickly and were a snap to install.
Thanks for saving me a ton of money / headaches!
Andy Read more...
Your Price
$49.28
In Stock
Magic Chef Dishwasher Sump Pump Check Valve
PartSelect Number PS11745441
Manufacturer Part Number WP8268375
May differ in appearance, but functions same as original.
This valve allows the water to flow in the drain direction only and prevents the dirty water from coming back into the tub.
Fixes these symptoms
- Leaking
- Noisy
- Not cleaning dishes properly
- See more...
Installation Instructions
Patty from Caldwell, ID
Dishwasher leaving food residue on all dishes
Had to take apart dishwasher and replace chopper assembly. The dishwasher had a lot of debris in in including pieces of broken plastic forks. Now works great
Read more...
Your Price
$49.32
In Stock
Magic Chef Dishwasher Impeller Assembly
PartSelect Number PS11747641
Manufacturer Part Number WP99002069
This impeller rotates and is used to force water up through to the spray arm.
Fixes these symptoms
- Noisy
- Not cleaning dishes properly
- Not draining
- See more...
Installation Instructions
William from Pottstown, PA
poor design causes filters to clog easily
removed lower spray arm and the 6 torx screws that hold the pump cover and secondary filter housing. Removed it and the filter. Removed the pump housing and removed the impeller nut with a 5/16 nutdriver. Removed the old impeller and put in the new one. Replaced the parts in reverse order.
Read more...
Your Price
$59.20
On Order
Magic Chef Dishwasher Pump Housing Kit
PartSelect Number PS11741266
Manufacturer Part Number WP3369011
This is the pump housing only.
Fixes these symptoms
- Leaking
- See more...
Your Price
$129.61
In Stock
Magic Chef Dishwasher Sump W/seal
PartSelect Number PS11746658
Manufacturer Part Number WP8572618
This part has a large port for the soil sensor and thermistor.
Fixes these symptoms
- Leaking
- See more...
Installation Instructions
reynaldo from San Antonio, TX
Leak around gasket
Long story short, noticed one of two leaks and came to conclusion there is no workaround since sump pump gasket seems to be hermetically sealed to sump pump. Which is understandable because of water in area. Wife helped by soaking other parts that were removed and replaced, because of calcium buildup. Which we hope will extend life of dishwasher. I put 1 to 2 hours because I took my time and made sure all parts fit correctly and were back in their original place. Didn't want to take any chances in not covering bases. I am no expert, but definitely a diy'er. I believed I saved myself anywhere from $200 to $300 in labor costs by repairman. By the way, thanks Parts Select your info and site are awesome!!! The second part I had to order was the water inlet valve and your phone representative was a big help over the phone, please don't eliminate those positions. Overall total price of parts approximately $130 w/delivery. Well worth it, since a brand new halfway decent dishwasher starts at $550.
Read more...
Your Price
$11.95
Special Order
Magic Chef Dishwasher Ball Check Valve
PartSelect Number PS11741274
Manufacturer Part Number WP3369178
Related Magic Chef Dishwasher Parts
- All Magic Chef Dishwasher parts
- Magic Chef Dishwasher Brackets and Flanges
- Magic Chef Dishwasher Caps and Lids
- Magic Chef Dishwasher Dishracks
- Magic Chef Dishwasher Dispensers
- Magic Chef Dishwasher Hardware
- Magic Chef Dishwasher Hinges
- Magic Chef Dishwasher Hoses and Tubes
- Magic Chef Dishwasher Latches
- Magic Chef Dishwasher Panels
- Magic Chef Dishwasher Seals and Gaskets
- Magic Chef Dishwasher Spray Arms
- Magic Chef Dishwasher Springs and Shock Absorbers
- Magic Chef Dishwasher Wheels and Rollers