Magic Chef Washer Agitators
- Search your model number to find:
- Genuine OEM parts guaranteed to fit
- Free manuals and guides
- Repair instructions and videos
Popular Magic Chef Washer Agitators
Your Price
$140.95
In Stock
Magic Chef Washer Agitator Kit
PartSelect Number PS334557
Manufacturer Part Number 285565
This agitator kit does NOT include the fabric softener dispenser (part 8575076A). That must be ordered separately.
Fixes these symptoms
- Spinning Issues
- Will not agitate
- See more...
Installation Instructions
Dexter from Milwaukie, OR
Washer made a loud banging noise at end of spin cycle, leaked water and agitator seemed loose
After entering the model number of your appliance you will be taken to a page where all of the parts are displayed by sections. On that page about in the middle there is a heading called "Find Part By Symptom." I figured out from there which symptom the washer had and read what other people were saying and how they made the repairs. Basically I had three problem areas, Noise, Leaking and a problem with the agitator. I focused on the loud noise first and decided I needed to replace the clutch/brake assemblies. I found the clutch parts page and on that page there was a video on how to make this repair. This video is all you need to gain access to all moving parts located under the cabinet. Which ever part you are replacing, I recommend watching this video! After removing the console, back panel and cabinet then laying the machine on its back just as seen on the video, I had access to the water pump, motor, transmission and related clutch/brake parts. As it turned out I did not need the clutch/brake assembly but as a precaution and because the parts were cheap, I replaced the motor coupling, water pump and tub wear pads. I decided to replace the agitator assembly because of several worn parts associated with the dog ears/drive shaft ETC. I put the machine back upright and took off the top cap on the agitator, then there is an inner cap with seal that gives access to the 7/16" bolt you must remove to remove the agitator. However once the agitator was removed I noticed metal shavings and play in the shaft. I used a spanner wrench to remove the spanner nut. I removed the Plastic Tub Ring (has several clips around the outer tub), then removed the inner washer tub to replace the Drive Block. Replacing the Drive Block stopped the loud noise at the end of the spin cycle. Now just reverse the order to put the machine back together and your done. For my situation it was best to take the machine apart and decide which parts I needed before ordering to minimize errors. These machines are made very cheaply and are designed to brake at some point in time and it is very easy to determine which parts are worn because most are made of plastic. In this process I also noticed where my leaks (did I say Leaks) were coming from. There were two hose clamps installed improperly from the factory, so check all clamps, hoses ETC. and you should be good to go.
Read more...
Your Price
$31.95
In Stock
Magic Chef Washer Agitator Repair Kit
PartSelect Number PS334622
Manufacturer Part Number 285748
This agitator repair kit comes with a long cam, a thrust spacer and four dogs ears (agitator cogs). This repair kit is used to move the upper agitator and it connects the base of the agitator with the agitator top (mover). This part has been updated by the manufacture.
Fixes these symptoms
- Will not agitate
- See more...
Installation Instructions
Steve from Naperville, IL
Top of agitator didn't agitate. It was slipping.
Pried off the agitator cap. Removed the bolt. Removed the agitator. In the process of separating the agitator from the base, a plastic tab broke off which concerned me. BUT, in the directions with the part it explains that the 2 tabs are for factory assembly and to break both of them off. Broke off the second tab and reassembled. My 18 year old Kenmore is back in action.
Read more...
Your Price
$6.95
In Stock
Magic Chef Washer Thrust Spacer
PartSelect Number PS334562
Manufacturer Part Number 285587
This is a genuine OEM thrust spacer for your washer, and is also commonly known as a retainer ring. The spacer is about 2.5 inches in diameter, is made of plastic, and is white in color. It is used in the agitator assembly of many direct drive washing machine models. The spacer is fitted between the agitator and the agitator auger to support it as it moves. This part is sold individually. Although it is not included in this part, you should have some dual-action agitator grease for the repair as well.
Fixes these symptoms
- Spinning Issues
- Spins slowly
- Will not agitate
- See more...
Installation Instructions
Craig from Polk City, FL
Washer not agitating
On top of the agitator is a flat cap that is held in place by the friction of an o-ring, there are no fasteners. I would imagine one could get under the lip with a small screwdriver or butter knife to pop it off but I chose simply using my fingernails so as to not disfigure the cap. Under the cap you will find the head of the only bolt that holds the assembly together it is a 7/16 head and because it is in a 4" deep well your will need a 6" extension for your ratchet. Once the bolt is out the top of the agitator, the assembly with the cogs removes by hand. Set the assembly upside down on the counter, slide the black plastic ring off, pull the cogs out with your fingertips, install the new cogs put a new black ring on and set the assembly back in the agitator. Reinstall bolt. As the bolt is down in a tube, you cannot set it in place with your fingers and it will fall out of the socket. To hold the bolt in the socket during positioning you can either put a gob of Vaseline on the bolt head to hold it in the socket or form a small piece of paper over the bolt head and set it into the socket, the friction of the paper will hold the bolt into the socket. Took me less then 10 minutes, good luck
Read more...
Your Price
$84.33
In Stock
Magic Chef Washer Washing Machine Agitator Base
PartSelect Number PS11741151
Manufacturer Part Number WP3347288
This is not the full agitator assembly. This is just the agitator base.
Fixes these symptoms
- Spinning Issues
- Will not agitate
- See more...
Your Price
$10.45
In Stock
Magic Chef Washer Agitator Cap
PartSelect Number PS11741199
Manufacturer Part Number WP3355758
This is the cap for your agitator.
Fixes these symptoms
- Will not agitate
- See more...
Installation Instructions
Virginia from Philadelphia, PA
The old lint filter was worn, and would "pop up" so that clothes weren't being moved about during the wash and rinse cycles. If I didn't frequently push it down again, it would fly off during a spin cycle. Dangerous!
I simply lifted the lint filter and its cap off, pressed the new agitator cap onto the new lint filter and put the assemblage into place. No tools needed at all. A $50 dollar repair saved me from replacing my washer/dryer! I'm very pleased.
Read more...
Your Price
$94.59
In Stock
Magic Chef Washer Upper Agitator
It would be helpful if this information were given when ordering these replacement parts. You then put the auger and cam on the agitator and place the assembly back on the shaft in the wash tub and replace the mounting bolt and tighten it. Remember to not overtighten it. Then you place the inner cap/seal back inside the mover after lubricating the seal with plumber's grease or liquid soap and replace the dispenser cap. The instructions remind you that the mover is to turn only clockwise and, if that's what you have, you are finished. As a precaution, I checked the "play" (and there is some in it) in the mover/auger after assembly then checked it again after the first couple of loads we washed. It seems to be fine.
Please don't let the length of this story alarm or discourage you. I'm trying to include everything which might be helpful to anyone who wants to do this. It really isn't difficult. Incidentally, it probably wasn't necessary to replace the mover/auger in my machine as it looked to be in very good condition, but I thought it wise (at another's suggestion) to replace it in case it might wear the other parts prematurely. I hope this helps somebody out there and that I didn't forget anything. Again, the parts come with very good instructions. Just don't forget the grease! Read more...
PartSelect Number PS11741159
Manufacturer Part Number WP3348752
This white clothes mover is designed for the upper portion of the agitator.
Fixes these symptoms
- Will not agitate
- See more...
Installation Instructions
Claude from Beckley, WV
Clothes mover stopped working. Found, after disassembly, that cam dogs were broken into many pieces.
I first pulled the softener dispenser cap off, then re-moved the inner cap/seal by twisting and pulling (it was a little stubborn, but alternating my grip from side to side while pulling was helpful). Using a 7/16" socket with an extension to reach down inside the mover, I then loosened the agitator mounting bolt. Note the amount of torque needed to "break " the bolt from the threads holding it as you don't want to overtighten it when you replace it. It doesn't require much effort to tighten it., depend-ing on the size of your wrench. I then lifted the agitator up and off its shaft by slipping my fingers under it on opposite sides of its base. Then, I lifted the mover or auger off the agitator and removed the thrust washer, cam and cam dogs. Don't worry; the illustrated instructions which are included with the new parts are quite clear and understandable. Then, I placed the new thrust washer and cam and dogs (a separate instruction sheet shows you how to assemble the cam, dogs and bearing; not difficult). Here's the only complaint I have about all this: the instructions advise you to apply agitator grease to the top surface of the thrust washer, but the grease isn't included in the kit. I used standard plumber's silicone grease which I had on hand. Hopefully, that won't be a problem. There's a part # for the grease shown on the illustration (#350849).It would be helpful if this information were given when ordering these replacement parts. You then put the auger and cam on the agitator and place the assembly back on the shaft in the wash tub and replace the mounting bolt and tighten it. Remember to not overtighten it. Then you place the inner cap/seal back inside the mover after lubricating the seal with plumber's grease or liquid soap and replace the dispenser cap. The instructions remind you that the mover is to turn only clockwise and, if that's what you have, you are finished. As a precaution, I checked the "play" (and there is some in it) in the mover/auger after assembly then checked it again after the first couple of loads we washed. It seems to be fine.
Please don't let the length of this story alarm or discourage you. I'm trying to include everything which might be helpful to anyone who wants to do this. It really isn't difficult. Incidentally, it probably wasn't necessary to replace the mover/auger in my machine as it looked to be in very good condition, but I thought it wise (at another's suggestion) to replace it in case it might wear the other parts prematurely. I hope this helps somebody out there and that I didn't forget anything. Again, the parts come with very good instructions. Just don't forget the grease! Read more...
Your Price
$115.03
In Stock
Magic Chef Washer Shaft, Agitator (complete)
PartSelect Number PS11741981
Manufacturer Part Number WP389387
This kit is used for direct drive washing machines and is found inside the gearcase.
Fixes these symptoms
- Will not agitate
- See more...
Installation Instructions
Adam from Lehi, UT
Agitator had a terrible ratcheting sound when running in free-wheel mode during spin cycle.
Removed the gearbox from the drum and removed the direct drive motor from the gearbox. Disassembled gearbox and drained gear oil. Rebuilt the neutral drive assembly with the ordered parts. Cleaned sealing surfaces. Filled gearbox with new gear oil. Sealed and re-installed the top cover to the gearbox. Reattached motor and then reinstalled assembly to drum and clutch (installed new clutch lining at this time as well).
Read more...
Your Price
$85.20
In Stock
Magic Chef Washer Upper Agitator
PartSelect Number PS11741229
Manufacturer Part Number WP3360824
Check out the Upper Agitator from Whirlpool, a reliable genuine OEM part. This upper agitator assembly is designed to enhance the performance of your washing machine. It plays a crucial role, spinning and rotating to efficiently move the laundry through the water. Before installation, remember to shut off the water supply and unplug the washer for safety. Ensure to don work gloves to protect your hands during this process. Trust this high-quality part from Whirlpool to maintain the superior operation of your appliance.
Fixes these symptoms
- Will not agitate
- See more...
Your Price
$184.09
On Order
Magic Chef Washer Agitator(complete)
PartSelect Number PS11748244
Manufacturer Part Number WPW10093671
Your Price
$96.53
Special Order