Maytag Washer Dryer Combo Drums and Tubs
- Search your model number to find:
- Genuine OEM parts guaranteed to fit
- Free manuals and guides
- Repair instructions and videos
Popular Maytag Washer Dryer Combo Drums and Tubs
Your Price
$13.62
In Stock
Maytag Washer Dryer Combo Front Glide Kit
2. Removed 4 screws from inside the dryer, to take off the blower housing.
3. Removed 4 screws and took out the large metal piece which supports the drum at the front. Removed the drum.
4. Replaced the two rollers that support the drum in the rear. Cleaned the pins they run on, and oiled very lightly. Also replaced the idler roller. I was surpirsed to see that these rollers use plain bearings, not ball bearings.
5. On the front support piece, drilled out the rivets for the glides, and replaced the worn out glides with new parts. Applied a little glue (3M weatherstrip adhesive) to the cork pieces, to glue them to the metal. Attached the plastic pieces over the cork pieces, and riveted in place using rivets that came with the glide kits.
6. Replaced front and rear felt seals. This was not as tricky as I expected it to be. They were held in by metal tabs. Glued the ends where they came together.
7. Replaced the felt blower seal. Glued to the blower housing.
8. Reinstalled the drum, installed new belt, which came with good instructions (luckily).
9. Reassembled front support piece and the front of the cabinet.
I also cleaned the lint from the cabinet and from the vent hose.
In general, the job went without a hitch, and the machine probably has quite a few years left, despite the fact that it's 18 years old. This gives me a good feeling.
I'd say this would be challenging, though, for someone who is not pretty experienced with machinery repair. Also, the cost of the parts was significant enough that it would not have been unreasonable to have opted for a new machine. Read more...
PartSelect Number PS1804752
Manufacturer Part Number 306508
The front glide is located at the front of the dryer, the drum rides along it. If you hear a metal-on-metal noise when your dryer is running, your front glide may be worn out and require replacing. This front glide kit comes with a blue plastic glide, a brown cork pad, and two metallic rivets. Two kits are required per appliance. While you have the front bulkhead removed for this repair, you may want to inspect the felt that lines it. If the felt is damaged, it is recommended that you replace it at the same time. You will need a rivet tool for this installation, as well as a stubby Phillips screwdriver, a 5/16 nut driver, and a drill with a 1/8-inch bit.
Fixes these symptoms
- Drum Not Spinning
- Marks left on clothes
- Noisy
- See more...
Installation Instructions
John from Charlottesville, VA
Belt broke on old machine.
1. Removed front of machine (2 screws at the bottom).2. Removed 4 screws from inside the dryer, to take off the blower housing.
3. Removed 4 screws and took out the large metal piece which supports the drum at the front. Removed the drum.
4. Replaced the two rollers that support the drum in the rear. Cleaned the pins they run on, and oiled very lightly. Also replaced the idler roller. I was surpirsed to see that these rollers use plain bearings, not ball bearings.
5. On the front support piece, drilled out the rivets for the glides, and replaced the worn out glides with new parts. Applied a little glue (3M weatherstrip adhesive) to the cork pieces, to glue them to the metal. Attached the plastic pieces over the cork pieces, and riveted in place using rivets that came with the glide kits.
6. Replaced front and rear felt seals. This was not as tricky as I expected it to be. They were held in by metal tabs. Glued the ends where they came together.
7. Replaced the felt blower seal. Glued to the blower housing.
8. Reinstalled the drum, installed new belt, which came with good instructions (luckily).
9. Reassembled front support piece and the front of the cabinet.
I also cleaned the lint from the cabinet and from the vent hose.
In general, the job went without a hitch, and the machine probably has quite a few years left, despite the fact that it's 18 years old. This gives me a good feeling.
I'd say this would be challenging, though, for someone who is not pretty experienced with machinery repair. Also, the cost of the parts was significant enough that it would not have been unreasonable to have opted for a new machine. Read more...
Your Price
$28.95
In Stock
Maytag Washer Dryer Combo Tall Baffle
PartSelect Number PS11741085
Manufacturer Part Number WP33002032
This part moves the clothes around inside your dryer and helps to direct the flow of hot air during the drying cycle.
NOTE: Screws are NOT included.
Fixes these symptoms
- Noisy
- See more...
Installation Instructions
Teresa from Pace, FL
dried too many shoes and broke the baffles
removed door, removed screws to lift top panel, removed screws that held old baffles, replaced with new baffles, took off front panel and cleaned out excess lint while I was in there.
Read more...
Your Price
$31.95
In Stock
Maytag Washer Dryer Combo Short Baffle
PartSelect Number PS11741064
Manufacturer Part Number WP33001755
This part moves the clothes around inside your dryer and helps to direct the flow of hot air during the drying cycle.
Fixes these symptoms
- Noisy
- See more...
Installation Instructions
Teresa from Pace, FL
dried too many shoes and broke the baffles
removed door, removed screws to lift top panel, removed screws that held old baffles, replaced with new baffles, took off front panel and cleaned out excess lint while I was in there.
Read more...
Your Price
$74.79
In Stock
Maytag Washer Dryer Combo Ring Balance
PartSelect Number PS11741965
Manufacturer Part Number WP387240
Installation Instructions
James from Asheville, NC
Washing machine shakes violently during spin cycle
Removed four screws that hold the top control panel to the base and hung over the back panel in order to remove the main wrap-around body of the machine. Took off top plastic ring fastened to side of tub then removed old Balance ring. Installed new balance ring. Unfortunately, this did NOT fix the problem. This was a suggestion from Justanswer.com and failed miserably. Does anybody know how to fix this problem? And it's not the springs or the little plastic shims around the base OR the cross coupling to the motor...
Read more...
Your Price
$88.32
In Stock
Maytag Washer Dryer Combo Washer Ringtub
PartSelect Number PS11765521
Manufacturer Part Number W10880720
Introduce your washer to the Whirlpool's top-notch Tub Ring. A genuine OEM part, this tub ring is compatible with certain models of several popular brands including Whirlpool, KitchenAid, Maytag, Jenn-Air, Amana, Inglis, and Magic Chef. This tub ring clicks perfectly over the top of your washer's tub serving as a solid splash shield. Although the assembly might comprise multiple components, please reference the parts diagram for a detailed segment list. Remember, wearing work gloves during installation can help protect your hands. Trust Whirlpool's Tub Ring for a clean, leak-free laundry experience at home.
Your Price
$161.94
In Stock
Maytag Washer Dryer Combo Drum Assembly
PartSelect Number PS8691313
Manufacturer Part Number W10518375
Your Price
$120.49
In Stock
Maytag Washer Dryer Combo Drum & Tub
PartSelect Number PS12665094
Manufacturer Part Number WP3349292
Tub
Your Price
$132.61
Special Order
Your Price
$708.95
In Stock
Maytag Washer Dryer Combo Outer Tub With Bearing
The washer's sound during spin cycle had changed over time from a jet-engine whine to a low rumble. Inspection from the rear revealed that the seals between the spinner and outer tub had failed, and the bearings had been damaged by water intrusion. The bearings are not a replacement item. They are installed as part of the outer tub assembly, so the whole outer tub must be replaced. This requires almost complete disassembly of the washing machine.
The disassembly was relatively easy with the maintenance manual in hand. I had to use a gear puller to remove the pulley, though. I decided to replace not only the outer tub, but the spinner shaft as well since I believed the shaft may have been damaged when the bearings failed.
Reassembly was not so easy. I installed the outer tub, then wrestled with the heavy counterweights. The lower weight was particularly unwieldy, since I had support it from below while attaching it to the bottom of the tub. I finally used books of different thicknesses to hold the weight in place while locating the screw holes for attachment. The upper weight attached easily after I wrestled it into position. This is a concrete weight of about 25 lbs, I would guess.
The other problem was attaching the outer tub cover with the rubber boot attached. It is held by 12 clips, and it was difficult to seat the cover tight enough to attach the clips. I started at the bottom and worked around, instaling clips as I went. The last 4 clips were the hardest; I had to cinch up the cover with C-clamps before installing the clips.
The rest of the assembly was not difficult.
I had my wife help locate the new tub on the struts in the back and to help support the motor while I hung it on the outer tub. Otherwise, this is a one-man repair.
Total cost around $350, thanks to Partselect.com reasonable prices. I shopped around and they offered the best price snd excellent service.
I spent about 8 hours on this job. Read more...
PartSelect Number PS2021871
Manufacturer Part Number 22004465
This kit includes the outer tub, front and rear bearing, water deflector, hose clamp, spacer, mtr isolator, plug and lip seal.
NOTE: The bearing is NOT sold separately from the outer tub.
Installation Instructions
Stephen from Ft Lauderdale, FL
Bearings between spinner and outer tub replaced
The Neptune stacked washer/dryer maintenance manual was a must-have for this repair.The washer's sound during spin cycle had changed over time from a jet-engine whine to a low rumble. Inspection from the rear revealed that the seals between the spinner and outer tub had failed, and the bearings had been damaged by water intrusion. The bearings are not a replacement item. They are installed as part of the outer tub assembly, so the whole outer tub must be replaced. This requires almost complete disassembly of the washing machine.
The disassembly was relatively easy with the maintenance manual in hand. I had to use a gear puller to remove the pulley, though. I decided to replace not only the outer tub, but the spinner shaft as well since I believed the shaft may have been damaged when the bearings failed.
Reassembly was not so easy. I installed the outer tub, then wrestled with the heavy counterweights. The lower weight was particularly unwieldy, since I had support it from below while attaching it to the bottom of the tub. I finally used books of different thicknesses to hold the weight in place while locating the screw holes for attachment. The upper weight attached easily after I wrestled it into position. This is a concrete weight of about 25 lbs, I would guess.
The other problem was attaching the outer tub cover with the rubber boot attached. It is held by 12 clips, and it was difficult to seat the cover tight enough to attach the clips. I started at the bottom and worked around, instaling clips as I went. The last 4 clips were the hardest; I had to cinch up the cover with C-clamps before installing the clips.
The rest of the assembly was not difficult.
I had my wife help locate the new tub on the struts in the back and to help support the motor while I hung it on the outer tub. Otherwise, this is a one-man repair.
Total cost around $350, thanks to Partselect.com reasonable prices. I shopped around and they offered the best price snd excellent service.
I spent about 8 hours on this job. Read more...
Your Price
$68.19
Special Order
Maytag Washer Dryer Combo Dryer Drum Baffle
PartSelect Number PS11731200
Manufacturer Part Number W10852390
Related Maytag Washer Dryer Combo Parts
- All Maytag Washer Dryer Combo parts
- Maytag Washer Dryer Combo Belts
- Maytag Washer Dryer Combo Brackets and Flanges
- Maytag Washer Dryer Combo Caps and Lids
- Maytag Washer Dryer Combo Circuit Boards and Touch Pads
- Maytag Washer Dryer Combo Doors
- Maytag Washer Dryer Combo Ducts and Vents
- Maytag Washer Dryer Combo Elements and Burners
- Maytag Washer Dryer Combo Filters
- Maytag Washer Dryer Combo Fuses
- Maytag Washer Dryer Combo Hardware
- Maytag Washer Dryer Combo Hinges
- Maytag Washer Dryer Combo Hoses and Tubes
- Maytag Washer Dryer Combo Knobs
- Maytag Washer Dryer Combo Latches
- Maytag Washer Dryer Combo Motors
- Maytag Washer Dryer Combo Panels
- Maytag Washer Dryer Combo Seals and Gaskets
- Maytag Washer Dryer Combo Springs and Shock Absorbers
- Maytag Washer Dryer Combo Switches
- Maytag Washer Dryer Combo Thermostats
- Maytag Washer Dryer Combo Valves
- Maytag Washer Dryer Combo Wheels and Rollers
- Maytag Washer Dryer Combo Wire Plugs and Connectors