Enter the code USA15 at checkout to apply your discount. Discount will be applied at checkout when the code is entered & applies to all parts. Cannot be combined with any other coupon or special offer & cannot be applied to a previously placed order. Not valid toward tax or shipping & handling. Discount has no cash value. Discount expires on July 1 at 11:59pm EST.
Microwave Oven Combo Circuit Boards and Touch Pads
- Search your model number to find:
- Genuine OEM parts guaranteed to fit
- Free manuals and guides
- Repair instructions and videos
Popular Microwave Oven Combo Circuit Boards and Touch Pads
Microwave Oven Combo Display Control Board
PartSelect Number PS1022528
Manufacturer Part Number WB27X10858
Fixes these symptoms
- Touchpad does not respond
- See more...
Microwave Oven Combo Digitron
Step one: Disconnect the power to the Advantium 120. Unplug unit, trip the breaker, whatever. Your responsibility to make sure the electrical power is removed.
For cabinet mounted units remove four screws from front side flange holding the microwave to cabinet
On the cabinet mounted model access three screws along the top front edge of case behind the display then one screw on each side of display and two hidden screws accessed through the top of the case via access holes. (use a magnetic see driver for these screws)
Work the display panel off and support it until the connectors are removed.
There are three small color coded plugs on the left side to the PC board and five larger colored plugs on the right side. Note plug locations.
Lay the removed control panel upside down on a towel at the corner of the sink so the selector knob is not resting on the counter.
Remove PC plug to the display and remove four screws on the PC board. Shift the PC board to release the tabs. Then remove two screws holding the PC display board. Note two guide pins also align the PC board.
Remove the rubber insulator from the old board and put it at the same location on the new board. There is usually enough stickiness on this insulator to put it back on the new board.
Installation is reverse. Reconnect power. Try it out after completion by boiling water in a microwave safe container. My new display was much brighter than the replaced display. No flashing. Read more...
PartSelect Number PS1018741
Manufacturer Part Number WB27X10856
Installation Instructions
William from EAGLE, ID
Flashing display
Replace Advantium 120 flashing display.Step one: Disconnect the power to the Advantium 120. Unplug unit, trip the breaker, whatever. Your responsibility to make sure the electrical power is removed.
For cabinet mounted units remove four screws from front side flange holding the microwave to cabinet
On the cabinet mounted model access three screws along the top front edge of case behind the display then one screw on each side of display and two hidden screws accessed through the top of the case via access holes. (use a magnetic see driver for these screws)
Work the display panel off and support it until the connectors are removed.
There are three small color coded plugs on the left side to the PC board and five larger colored plugs on the right side. Note plug locations.
Lay the removed control panel upside down on a towel at the corner of the sink so the selector knob is not resting on the counter.
Remove PC plug to the display and remove four screws on the PC board. Shift the PC board to release the tabs. Then remove two screws holding the PC display board. Note two guide pins also align the PC board.
Remove the rubber insulator from the old board and put it at the same location on the new board. There is usually enough stickiness on this insulator to put it back on the new board.
Installation is reverse. Reconnect power. Try it out after completion by boiling water in a microwave safe container. My new display was much brighter than the replaced display. No flashing. Read more...
Microwave Oven Combo Wall Oven Noise Filter Board
PartSelect Number PS8747022
Manufacturer Part Number 5304492543
Microwave Oven Combo Electronic Clock Oven Control
PartSelect Number PS773585
Manufacturer Part Number WB27T10411
Please note: With this control the wiring could be differ from the original. It will possibly need to be installed by an appliance repair person.
Microwave Oven Combo Microwave Inverter
PartSelect Number PS2342258
Manufacturer Part Number W10217711
The inverter acts like the brain for the microwave. It sends high voltage to the magnetron to produce heat.
Fixes these symptoms
- No heat
- See more...
Your Price
$513.56
In Stock
Microwave Oven Combo Electronic Clock Control Board
2. Opened oven door used a phillips screwdriver to remove four black screws from under the top panel.
3. Lifted panel slightly & removed from oven.
Removed four screws using 1/4" nut driver to remove old display unit. Disconnected three wire harnesses.
4. Connected three wire harnesses to new display unit & replaced four nut screws.
5. Hang the top panel on the top of oven & replace four screws removed in step 2.
6. Turn on the circuit breaker for the oven.
("Very easy! I'm a 63 yr. old woman!) Read more...
PartSelect Number PS11743900
Manufacturer Part Number WP71003424
This electronic clock assembly is seven and a half inches long. It is three inches wide and is intended for use with a range's control panel.
Fixes these symptoms
- Will not program
- See more...
Installation Instructions
Cheryl from Mesa, AZ
No clock display
1. Turned off the circuit breaker for the oven.2. Opened oven door used a phillips screwdriver to remove four black screws from under the top panel.
3. Lifted panel slightly & removed from oven.
Removed four screws using 1/4" nut driver to remove old display unit. Disconnected three wire harnesses.
4. Connected three wire harnesses to new display unit & replaced four nut screws.
5. Hang the top panel on the top of oven & replace four screws removed in step 2.
6. Turn on the circuit breaker for the oven.
("Very easy! I'm a 63 yr. old woman!) Read more...
Microwave Oven Combo Oven Control Board
PartSelect Number PS11752580
Manufacturer Part Number WPW10312206
Microwave Oven Combo Noise Suppressor
PartSelect Number PS11742574
Manufacturer Part Number WP4451985
This part controls the voltage and helps to reduce interference on the control board