10651332716 Kenmore Refrigerator - Instructions

I knew the chances of all the freon leaking out was unlikely so I looked at the wiring to the compressor and there was a capacitor and a starter/overload so i figured I would start there. I went on line and found the parts at this site and they were less than the minimum service call charge for a service tech so I figured what the heck let's give her a shot so I did give it a shot. I ordered the parts and they were there in less time than a service tech could come out and i installed the parts and guess what for 90.00 in parts and 15 minutes in time I repaired my refrigerator. Thanks guys, It took less time to order the parts than it did to make the repair so thanks, your website rocks and is very well designed so my hat is off to you guys!

I used a flat-head screwdriver to pop out the old light rocker switch. Then, I unplugged the wires, plugged them into the new light rocker switch, and then popped the new switch into the hole. That's it! Lights began working again.

I used a flat screwdriver and released the lock tab on the bottom of the light switch, and pried the switch out, being careful to not damage the plastic around the mounting place of the switch, unplugged wiring from old switch, plugged in the new one and pushed the new switch into place. Job finished light switch now working.

An easy job for smaller hands. Removed the two bolts holding the light cover. Removed two electrical connections from the old switch by pinching the retaining clip,removed the switch, snapped in the new one and re-attached the connectors. Your online illustrations helped me to know that the plastic housing for the light switch would only swing down so far and was not intended to be removed. Saved me from breaking that plastic cover's tabs. This home repair saved me more than 5 times the cost of hiring a professional to do it. Very happy homeowner.

Perhaps a helpful hint:

When aI received the hose adapter/connector, I inserted the 2 hose ends only to have water drip from the connection.
I used a utility knife to remove an inch from each side, then reinserted the hoses. That made the differnce. Dry as a bone.

LG

Once I saw the replacement part I understood how to pry out the switch with a small screwdriver. Then just unplug the old one, plug in the new one and pop it into place.

The PartSelect site made it easy to correctly identify the correct part, it was inexpensive, and the shipping was fast.

I'm very pleased!

I removed the ice bucket,the gear is located under the ice bucket and engages when ice bucket sits on it and turns the tray for ice to fall in the shute,2 screws to remove and the gear comes off and I put the new one on and put the screws back,very easy to do, total time 5 minutes,repair man wanted to charge $114 for the part and $100 for labor,I did it all for $25 thru this site,I love this site,it gsaved me alot of money,thanks partselect.,

I turned the water and electricity off for the refrigerator.
(not sure if this is necessary but is safer)
Remove the ice bucket.
Cover the Ice auger with a hand towel to catch any screws which my get dropped.
Remove four Philips screws holding plastic cover to inside of the door. there are no clip/snaps to worry about but on/off switch needs to be un plugged. Remove cover.
Remove two nut head screws holding old ice maker.
Remove wiring harness from ice maker and lift ice maker up and out. There are two tabs on the door.
Unplug the wiring harness from the ice maker..

Installation: Press the wiring harness into clips on the new ice maker. Install ice maker onto door insuring it is over the tabs on door and the holes for nut screws line up. Plugging the wiring harness in and install two screws.

Plug on/off wiring onto switch and press plastic cover onto inside of door. Take care that it fits inside of rubber door seal. Install four philips screws.
Remove hand towel and install ice bucket making sure the ice maker is switched on. Close door.
Turn on water and electricity.

This took me 25 min. and I am sure would go faster if I had had instructions.

My refrigerator took awhile before it started to make cubes but has been working like new ever since.
This task is easy go for it.

changed the starter connected to the compressor

Simply move the appliance for access to the back side. Removed the lower metal access panel, locate the compressor ( black round object ) parts are on the left bottom of the compressor. Simply unplug the parts, and replace with new parts.The hard part was, getting my 72 year old body in position to do the job. As far as getting the right part, a young lady in Nova Scoita is the one to ask for help !! Ordered parts one day, and they were in my hands the next morning!!

Removed nuts and bolts in order to remove ice maker unit, and 4 screws from the surrounding shell to get to said icemaker unit. I'd say it was a 15 minute job, but that's kind of a lie. It took me about a week of procrastination. And then 15 minutes to remove one unit and then put in the new unit. It's very easy unless you're really lazy. In which case it's still easy, the hard part is getting outta your recliner.

tested bulb good ,replaced door switch first(least expensive)then ordered light socket and circuitboard.If clicking sound is heard replace circuitboard first to save on return shipping because the switch and socket where ok

1. Empty your fridge. Lighter is easier to move and this is the hardest step in the fix. 2. Move your fridge so you can get behind it. Unplug the fridge. 3. Use a 1/4in nut driver to remove the screws from the back panel. 4. Remove the back panel. 5. Locate the compressor (big cylinder, usually black) and find the capacitor (PS11757023) and start dev (PS11750123) plugged into the side of the compressor. 6. There is a steel spring restraint wire, remove this. 7. Remove the pin connector (plastic w/ wires going to it) by pressing and pulling gently. Remove the old capacitor and start dev. 8. Assemble the new capacitor and start dev to each other. 9. Plug the pin connector into the new replacement components. 10. Align the start dev to the location of the old components. There is a 3 pin outlet that aligns to the 3 plug holes on the start dev. Align the plug then push gently but firmly to seat the components back together. 11. Reinstall the restraint wire. 12. Reinstall the pack panel. 13. Put your refrigerator back in place and load it up! You're all done!

watched video. Very easy

This is in a rental house; Refrigerator/freezer has been off for a few weeks so just opened the freezer door and used screwdriver to pry out one corner then pliers to grab and pull old gasket (seal) off. Had the new one laid out overnight to relax it; placed one corner on and then the opposite corner then repeated the other two corners. Positioned the keeper edge plastic all of the way around to place the gasket in the door. Closed the door to check the seal and plugged unit back in. Waited and then checked air temp with hand held IR temp gauge. All checked good, no cold spots anywhere. Piece of cake!