Your coupon for will be reflected when you check out!
✖
Your coupon for
✖
Hello!
You're visiting the PartSelect site in U.S.
Would you like to shop on the Canadian site?
Stay on this site
Go to Canadian site
✖
Model Number Locations
1Select Category Type
Select Category Type
2Select Product Type
Select Product Type
3Select {MODEL} Type
Select {MODEL} Type
Sample Model Number Tags
Model numbers can be made up of numbers (1005400, for example) or a combination of letters and numbers (LAT1000AAE). The model number will most likely appear on either a paper sticker or a metal plate. Your appliance's model number tag may look similar to the sample model number tags shown here (model number highlighted in yellow):
122T02-0994-B1 Briggs and Stratton Engine - Overview
Save your modelModel Saved!
Save your model for later to make things easier.
Model has been saved to My Models. If you're not signed in, your lists are available on this device and will expire within 30 days.
Model has been saved to My Models.
This is a replacement air filter/AC cartridge for your small engine. The air filter prevents dirt and debris from entering the engine. Over time, the air filter can become clogged or damaged, and this...
$7.06
In Stock
Order now and your part arrives in 2-3 business days!
This part is the replacement spark plug for your engine. It measures approximately 2.5 inches by 1 inch. The spark plug creates the spark that ignites fuel in your engine during the combustion process...
$4.99
In Stock
Order now and your part arrives in 2-3 business days!
This is a replacement carburetor overhaul kit for your small engine. The carburetor is essential to the overall performance of your engine, and the carb can get clogged up over time for a variety of r...
$17.96
In Stock
Order now and your part arrives in 2-3 business days!
The Air Cleaner Gasket is used to provide a seal between the air cleaner base, and carburetor. It's a gray, composite material part, which is rated as "Easy" to install and will require a screw driver...
$5.19
In Stock
Order now and your part arrives in 2-3 business days!
The manufacturer-approved Ratchet Pawl (Starter Pawl) comes in a set of two (2). This part attaches inside the recoil assembly, and is used to engage the flywheel. if broken due to wear/damage it will...
$3.99
In Stock
Order now and your part arrives in 2-3 business days!
This needle and seat kit, also known as a float valve, is found in many types of liquid-fueled lawn equipment, such as carburetors. The valve regulates the flow of fuel into the float bowl. The needle...
$6.97
In Stock
Order now and your part arrives in 2-3 business days!
This genuine OEM engine gasket set is sourced directly from the manufacturer and includes the gaskets needed to seal the components in a gas-powered engine. This set ensures proper fit and performance...
$40.29
In Stock
Order now and your part arrives in 2-3 business days!
This part is the replacement gasket for the crankcase on your engine. The gasket helps to create a seal on the crankcase and prevent leaks. If you notice that your engine is not running at peak perfor...
Upgrade your equipment with this reliable Pulley/Spring Assembly from Briggs and Stratton. Known for their superior quality, Briggs and Stratton parts are designed to help prolong the life of your mac...
$20.78
In Stock
Order now and your part arrives in 2-3 business days!
Total disassemble, clean out water and any rust. hone cylinder, wire brush where needed,reassemble with new rings,gaskets and seals and lucas oil product. Started on second pull. Mowed lawn. If you have never done this sort of work before, probably should not attempt.
Inspected/removed fuel lines and found signs of leak. Removed and inspected carburetor and found that seals and gaskets were toast. Replaced said seals with ones from the kit that fit and replaced fuel lines.
Would be nice to have a fuel line kit with the big fuel line (tank to carb) and the little one (carb to engine) together
... Read more with all the necessary clamps.
All the gaskets needed to be replaced on the Briggs 6.75 flathead I was rebuilding. I ported and polished the ports and shaved the eyebrow between the valves and the piston. The gasket set was a perfect fit. It is a monster now. It doesn't sound like a lawnmower engine anymore
