All Installation Instructions for 1364

remove and replace

very easy remove the bad bulb install the new one

Parts Used:

Fluorescent Lamp/Bulb

Perry from Flushing, NY
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

10 of 24 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

hubcap fell off my coleman air compressor

repair didn't happen the part was the wrong size so i wasted $20 and my time because the part was on back order (which the website did not show) Will never use you service again, complete waste of time and money

Parts Used:

Air Compressor Hub Cap

Richard from AUBURN, WA
Difficulty Level:
Very Difficult
Total Repair Time:
More than 2 hours

3 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Air leak at pressure switch diaphram

Kobalt 15g compressor.
* unscrew 6 T-20 to remove compressor housing cover.

* disconnect 2x black wire and 2x wire, and 2x green.

* use hand torch (or lighter) to soften tubing.

034-0174 is a discontinued pressure swirch. Purchased 034-0192 which fit perfectly. Only difference between 0174 and 0192 is the unloader valve. Which I did not need as its my unit is piped separately.

Parts Used:

Pressure Switch

James from ANAHEIM, CA
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Fluorescent lamp bulb

Unscrew the metal rim and remove the glass window. Remove the old bulb by twesting the bulb towards you. Place the new bulb's pins into the slots and twest away from you. Place the metal rims back in place and screw them down.

Parts Used:

Fluorescent Lamp/Bulb

Danial from HILLSBORO, TX
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

dropped & broke the oven light bulb cover

popped the new one on!

Parts Used:

Range Light Cover

joseph from san jose, CA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

1 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Headlight stopped working

I tried to order a light socket but you sent me a blade then cancelled my order and refunded my money after I waited for the right part.

Parts Used:

Socket

Darrell from RICHMOND, VA
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

1 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Mixer began to make a noise on speed two and higher

We took our 30 plus year mixer apart. I removed the old grease. There was some crumbly looking grease in the main housing gear section where the nylon gear is located. It looked like it had flour mixed in it. Not certain. Removed as best possible all old grease and applied 6 oz. of new Benalene grease to all of the gears. Now it does not make the slight howl sound.

Parts Used:

Lawn Mower Grease Benalene (8 Oz)

LISA M from BATESVILLE, AR
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

6 of 21 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Solenoid failed due to excessive heat.

Removed back panel. Removed the defective solenoid on its bracket. Replaced it with the new door latch solenoid. This was relatively easy. Replaced the back panel. Tested self cleaning feature. Everything worked fine. I have preformed this same repair once before.

Parts Used: