Your coupon for will be reflected when you check out!
✖
Your coupon for
✖
Hello!
You're visiting the PartSelect site in U.S.
Would you like to shop on the Canadian site?
Stay on this site
Go to Canadian site
✖
Model Number Locations
1Select Category Type
Select Category Type
2Select Product Type
Select Product Type
3Select {MODEL} Type
Select {MODEL} Type
Sample Model Number Tags
Model numbers can be made up of numbers (1005400, for example) or a combination of letters and numbers (LAT1000AAE). The model number will most likely appear on either a paper sticker or a metal plate. Your appliance's model number tag may look similar to the sample model number tags shown here (model number highlighted in yellow):
Model has been saved to My Models. If you're not signed in, your lists are available on this device and will expire within 30 days.
Model has been saved to My Models.
This individually sold shear pin is an OEM replacement that is most typically used in snowblowers but can also be used within snowblower attachments for lawn tractors. Its main uses are connecting the...
$3.99
In Stock
Order now and your part arrives in 2-3 business days!
Sourced directly from the manufacturer, this replacement part is designed to secure otherwise loose parts in place, allowing the machine to operate properly. This Bow Tie Cotter Pin is not part of a k...
$3.99
In Stock
Order now and your part arrives in 2-3 business days!
This nut is a manufacturer-approved replacement part for various lawn and garden equipment. It is sold individually, not as part of a kit or assembly. Also referred to as a Lock Nut, it is resistant t...
$5.95
In Stock
Order now and your part arrives in 2-3 business days!
This carriage bolt measures 5/16-18 x .75 and fastens two parts in your machine together. It has a round domed head and a square underside so the bolt does not rotate once it has been secured into pla...
This knob is an authentic OEM replacement parts kit used in lawn and garden equipment engines. It includes a plastic knob and a threaded metal bolt used to fasten various components together. The bolt...
$5.94
In Stock
Order now and your part arrives in 2-3 business days!
This OEM-manufactured flange bearing supports and enables the smooth rotation of parts in your lawn equipment, such as the blade assembly, axle assembly, or steering components. This bearing has an in...
$5.95
In Stock
Order now and your part arrives in 2-3 business days!
This manufacturer-certified Ignition Key comes in black/silver and is used in the ignition slot to turn on the engine. If your key becomes damaged or lost (which these small keys easily are), this pa...
$18.33
In Stock
Order now and your part arrives in 2-3 business days!
This chute flange keeper is sourced from the original equipment manufacturer for use in snowblowers. The plastic keeper allows the snowblower chute to pivot, and secures the flange that connects the c...
Designed for use in various models of lawn and garden equipment, this part is not sold as part of a kit or assembly. It is made of metal, is gold in color, and is sold individually. This part may also...
$5.95
In Stock
Order now and your part arrives in 2-3 business days!
To disconnect the steering shaft to replace the bearing, there is a #3 Philips head screw on the underside of the deck which needs to be taken out. Chances are it hasn't been replaced before, so it is likely very tight. I ended up dropping the deck to allow for more room but it could probably be done with the deck in place the way I had t
... Read moreo do it. I had someone hold the steering wheel up top (not undoing the 13mm bolt holding the steering wheel in) and tried to unscrew the Philips, even after heating it with a torch still stripped out. The only way I could get the screw out was to take a pair of Vice Grips adjusted extremely tight to the outside of the screw and put the torch on it to heat it again. Then, turn the steering wheel to the left and when the Vice Grips get caught on the bottom of the mower, it will unthread the steering wheel from the screw. After the screw and washer are out *TAKE NOTE OF THE ORIENTATION OF THE WASHER*, I went to the hardware store and replaced the screw with a bolt that was 5/16 - 18 x .750 which was the closest length they had, took out the worn out bearing, popped in the new one, reinstalled the washer and bolt, then the deck. Even if you get the philips screw out without using Vice Grips, I would still recommend replacing it with a bolt.
