176432-0035-01 Briggs and Stratton Engine - Overview
Sections of the 176432-0035-01
[Viewing 15 of 15]
Keep searches simple, eg. "belt" or "pump".
Lawn Mower Spark Plug
PartSelect #: PS9140427
Manufacturer #: 796112S
This part is the replacement spark plug for your engine. It measures approximately 2.5 inches by 1 inch. The spark plug creates the spark that ignites fuel in your engine during the combustion process...
$4.99
In Stock
Engine Oil Seal
PartSelect #: PS9277860
Manufacturer #: 391086S
The Oil Seal is a manufacturer-approved rubber part which provides a seal between the crankcase and crankshaft by attaching around the axle shaft on the crankhouse housing. Installation is rated as "M...
$6.59
In Stock
Spring-Rewind Str
PartSelect #: PS8978476
Manufacturer #: 490179
This rewind starter spring or as it is also known, recoil spring, rewinds the pull robe back into the starter housing of your engine. The spring is made of metal, silver colored, and sold individually...
No Longer Available
Engine Starter Pulley
PartSelect #: PS8942071
Manufacturer #: 295871
Introducing the Briggs and Stratton Starter Pulley, a vital component for your appliance repair needs. Crafted with quality and precision, this pulley plays a significant role in your engine's start-u...
$15.80
In Stock
Engine Starter Clutch
PartSelect #: PS8968281
Manufacturer #: 399671
Discover the power of optimal engine performance with the Briggs and Stratton Starter Clutch. A vital piece of your garden equipment's engine, this starter clutch engages your machine's flywheel while...
$37.32
In Stock
Fuel Line
PartSelect #: PS9140673
Manufacturer #: 791745
This fuel line is compatible with several different makes and models of small engine equipment and is sold as an individual part. Equipped with the securing clamp, this rubber fuel line is used to tra...
$11.29
Special Order
Questions And Answers for 176432-0035-01
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Symptoms of the 176432-0035-01
[Viewing 1 of 1]
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Generator would not start, Birggs & Stratton recommended to replase Gasket Exhaust.
Remove the spark suppresser, 4 face screws, 2 bottom screws and the two screws the hold the gasket. I also had to back out the top screw of the cover it blocked and prevented the removal of the gasket.
Parts Used:
-
Alberto from PALMETTO BAY, FL
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Socket set
10 of 33 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Gas tank leaking, pull starter rivets worn, rope and rope bushing worn
The gas tank was a simple job, close the fuel shut off, remove fuel hose then back out 2 bolts on the mounting bracket. Reverse procedure to mount.
To replace the pull starter/recoil assy. Remove low oil warning light, and air filter housing then remove the 4 bolts holding the front cover. Once the front cover is free remove kill sw ... Read more itch wire
Drill out the rivets holding the recoil housing w/ 3/16 bit. Screws w/ nuts are included to use in place of rivets, I used red Locktite on the screws which hold the started recoil to the front cover. Make sure the pull rope is correctly oriented in the 11:00 position. Replace front cover, four bolts. Air filter housing, kill switch wire and low oil warning light
To replace the pull starter/recoil assy. Remove low oil warning light, and air filter housing then remove the 4 bolts holding the front cover. Once the front cover is free remove kill sw ... Read more itch wire
Drill out the rivets holding the recoil housing w/ 3/16 bit. Screws w/ nuts are included to use in place of rivets, I used red Locktite on the screws which hold the started recoil to the front cover. Make sure the pull rope is correctly oriented in the 11:00 position. Replace front cover, four bolts. Air filter housing, kill switch wire and low oil warning light
Read less
Parts Used:
-
Dennis from EUFAULA, OK
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver, Screw drivers, Socket set, Wrench set
1 of 6 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!