31433 LG Washer Dryer Combo - Overview
Sections of the 31433
[Viewing 3 of 3]
Keep searches simple, eg. "belt" or "pump".
Water Inlet Valve
PartSelect #: PS12374721
Manufacturer #: AJU75152601
This is an authentic LG water inlet valve for a top-load washer. It is designed to control the flow of water into the washer. If your washer is filling slowly, making loud noises, overflowing, or stop...
$147.13
In Stock
Washer Pulsator Cap
PartSelect #: PS3525704
Manufacturer #: 5006EA3009B
This part is known as a pulsator cap or washplate cap, and is designed for your LG washer. It fits over the washplate mounting bolt and prevents clothes from getting caught on the washplate during a w...
$44.83
In Stock
Screw
PartSelect #: PS3534421
Manufacturer #: FAB30598601
Introducing the customized screw designed exclusively for LG washers. Manufactured with safety and efficiency in mind, installation is straightforward when you adhere to correct safety regulations. Sh...
$20.67
In Stock
Washer drain Hose Assembly
PartSelect #: PS8749199
Manufacturer #: AEM73732901
This drain hose is a genuine OEM replacement part supplied by LG for use in their washing machines. It is a light gray pipe with a diameter of 1.25 inches. The drain hose is connected to the drain pum...
$44.04
In Stock
Washer Switch Assembly sensor
PartSelect #: PS3529177
Manufacturer #: 6501EA1001R
This water-level pressure switch in your wash monitors and regulates the water levels throughout the fill, wash, and rinse cycles. You will usually find it inside the control panel or near the tub. It...
$63.16
In Stock
HOUSING ASSEMBLY,CLUTCH COUPLING
PartSelect #: PS12580053
Manufacturer #: AEN73651402
This clutch housing assembly with mode shifter, or washer drive shaft and shifter assembly, is made for your washer. It connects the appliance wash plate to the motor so the washer can shift the drive...
$276.55
In Stock
Motor Assembly Clutch
PartSelect #: PS3579314
Manufacturer #: 4681EA1009C
Enhance the lifetime of your LG washing machine with the genuine Original Equipment Manufacturer (OEM) Motor Assembly Clutch. This crucial component aids in shifting the drive system between spin and ...
$122.93
In Stock
Exact Part matches for your search term
[Viewing 2 of 2]
Decal, Control
This part number matches the current model number 31433
PartSelect #: PS9358331
Manufacturer #: 31433
$5.15
Special Order
Decal
This part number matches the current model number 31433
PartSelect #: PS12447882
Manufacturer #: 31433
$3.99
Special Order
Questions And Answers for 31433
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Symptoms of the 31433
[Viewing 8 of 8]Leaking
Fixed by
these parts
these parts
Show All
Water Filling Issues
Fixed by
these parts
these parts
Show All
Will not agitate
Fixed by
these parts
these parts
Show All
No hot or cold water
Fixed by
these parts
these parts
Show All
Will Not Start
Fixed by
these parts
these parts
Show All
Spinning Issues
Fixed by
these parts
these parts
Show All
Draining Issues
Fixed by
these parts
these parts
Show All
Marks left on clothes
Fixed by
these parts
these parts
Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Water continued leaking into washer after the end of cycle through the water inlet valve.
-
Flora from MIAMI, FL
-
Difficulty Level:Very Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Screw drivers, Wrench (Adjustable)
12 of 17 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
LOUD GRINDING/ROARING NOISE, INTERMITTANT SPIN
Watch this video on youtube:https://www.youtube.com/watch?v=8ZKgP6hu8Fk very similar
Keep all parts separate and in order in a plastic box with dividers
1. Disconnect washer from wall. (electrical and hot/cold hoses, drain tube)
2. Remove center cap from bottom tub plate
3. Remove small bolt under cap
4. R ... Read more emove bottom Tub Plate
5. Remover washer
6. Remove larger 38mm nut (I bought the correct deep well socket) Ive seen other video use a pipe wrench)
6a. Remove the large washer under nut
NOTE- I did not remove the tub, total hassle, found it unnecessary, Yes the washer was heavier but nothing that cant be managed.
7. Place a blanket on the floor and lay the washer on its back to access the bottom.
NOTE Everthing is nuts and bolts at this point. 10mm socket worked on all
8. Remove Nut & washer on rotor. Remove rotor-its has a line of magnets and the edges are sharp. Just wiggle it a bit. wear gloves if need be.
9. Remove bolts from Stator, user a small flat blade screw driver to undo 1 or 2 (some) electrical connections. Lay the stator aside. Move the electric connector(s) out of the way.
10. Remove the grounding wire at 6 oclock position
11.Remove the rectangular pack and the 3 oclock position by removing 2 bolts. It has a small arm that reaches out to the clutch arm, slide the piece out to the widest part of hole in clutch arrn an wiggle it loose.
Almost there....
12. Remove all the 10MM headed bolts from the clutsh and drive assemble The inner bolts are a slightly different style, keep the two sets separate.
13. Remove the clutch and drive.
NOTE: if the drive doesnt come out with a slight pull, you have missed a bolt(s)-inspect and remove as need be
14 Wipe clean the pocket in the outer wash tub that accepts the seal on the top of the drive. Lubricate the new drives seal completely with a little dishwasher detergent so it slides smoothly and seals well.
15. Assembly is the reverse:
Last Notes:
*Install all bolts for the clutch and drive hand tight as you get everything lined up.
*Once all bolt are in the clutch and drive are hand tight, tighten the bolts in a cross pattern as you would a wheels lug nuts
*Snug the bolts used to attached the clutch and drive firmly 1/8 to 1/4 turn past snug
*Make sure you clock the stator to the correct position, again hand tighten bolts then final tighten in a cross pattern.
*The nut and washer in the rotor tighten to 1/4 to 1/2 turn past snug, its tight.
*The large 38 MM nut on the top of the drive assembly torque is 88 ft lbs. Have a partner or friend hold the tub while you torque the large nut. If you don't have a torque wrench you can rent one from a number of auto-part chain stores.
*I used a 1/2 Impact gun to remove the 38mm nut, Never use that kind of power to reassemble as it will damage parts.
Good luck, you can do it.
Keep all parts separate and in order in a plastic box with dividers
1. Disconnect washer from wall. (electrical and hot/cold hoses, drain tube)
2. Remove center cap from bottom tub plate
3. Remove small bolt under cap
4. R ... Read more emove bottom Tub Plate
5. Remover washer
6. Remove larger 38mm nut (I bought the correct deep well socket) Ive seen other video use a pipe wrench)
6a. Remove the large washer under nut
NOTE- I did not remove the tub, total hassle, found it unnecessary, Yes the washer was heavier but nothing that cant be managed.
7. Place a blanket on the floor and lay the washer on its back to access the bottom.
NOTE Everthing is nuts and bolts at this point. 10mm socket worked on all
8. Remove Nut & washer on rotor. Remove rotor-its has a line of magnets and the edges are sharp. Just wiggle it a bit. wear gloves if need be.
9. Remove bolts from Stator, user a small flat blade screw driver to undo 1 or 2 (some) electrical connections. Lay the stator aside. Move the electric connector(s) out of the way.
10. Remove the grounding wire at 6 oclock position
11.Remove the rectangular pack and the 3 oclock position by removing 2 bolts. It has a small arm that reaches out to the clutch arm, slide the piece out to the widest part of hole in clutch arrn an wiggle it loose.
Almost there....
12. Remove all the 10MM headed bolts from the clutsh and drive assemble The inner bolts are a slightly different style, keep the two sets separate.
13. Remove the clutch and drive.
NOTE: if the drive doesnt come out with a slight pull, you have missed a bolt(s)-inspect and remove as need be
14 Wipe clean the pocket in the outer wash tub that accepts the seal on the top of the drive. Lubricate the new drives seal completely with a little dishwasher detergent so it slides smoothly and seals well.
15. Assembly is the reverse:
Last Notes:
*Install all bolts for the clutch and drive hand tight as you get everything lined up.
*Once all bolt are in the clutch and drive are hand tight, tighten the bolts in a cross pattern as you would a wheels lug nuts
*Snug the bolts used to attached the clutch and drive firmly 1/8 to 1/4 turn past snug
*Make sure you clock the stator to the correct position, again hand tighten bolts then final tighten in a cross pattern.
*The nut and washer in the rotor tighten to 1/4 to 1/2 turn past snug, its tight.
*The large 38 MM nut on the top of the drive assembly torque is 88 ft lbs. Have a partner or friend hold the tub while you torque the large nut. If you don't have a torque wrench you can rent one from a number of auto-part chain stores.
*I used a 1/2 Impact gun to remove the 38mm nut, Never use that kind of power to reassemble as it will damage parts.
Good luck, you can do it.
Read less
Parts Used:
-
MIKE from LANDENBERG, PA
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:More than 2 hours
-
Tools:Pliers, Screw drivers, Socket set
10 of 13 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Water overflow in washer basin
I diagnosed by running a full wash. I watched it and when the water should have stopped it kept running. I unplugged the washer from the power and the water kept running. This told me the inlet valve was the issue and not an electronic issue. I stopped the water by closing the water valve manually. Replacing the inlet valve was very easy
... Read more
. Hardest part is moving the washer out of the laundry room. The videos online show very simple steps. Maybe 8 screws to remove and a couple of hoses and five electronic connectors. Take a photo of connectors before removing them to ensure you reconnect properly.
Read less
Parts Used:
-
Ed from LAKE WORTH, FL
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Pliers, Screw drivers
10 of 14 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!