3639631375 Kenmore Refrigerator - Instructions

I had to call for a appointment for repair with GE Appliance because I thought then it . .was something electrical. The technician came out & checked everything out, turned out it was not electrical, The technician went out to his truck got a light bulb from his truck, put it in & it worked. It cost me $121.00 for trip charge from GE appliance for a light bulb that worked, your light bulbs were defective twice. Very disappointed with your products, cost me alot of money for a good light bulb thru GE appliance

Unplugged the appliance for safety. Removed two 1/4" screws that held the assembly in place. Carefully removed the wire guard that retains the glass shield. Unscrewed old light bulb and replaced with new part. Reversed the steps after cleaning glass cover.

I took out the vegetable bins and slid in the part. Replaced vegetable bins. Works perfect. I was told locally that GE doesn't make the part any more and that I wouldn't be able to find one. First place I looked on the net was you and found it with no trouble at all. really thrilled to get it. Thanks

First i removed everything from the bottom shelf, removed the glass, then removed the entire bracket assembly. Then removed the front metal strip to expose the front mounting screw, then removed the rear screw. Installed the new part and reversed the procedure.

Removed the 2 drawers and then the glass shelf.
Positioned the drawer slid and tightened to rear screw and the front screw.

Replaced the shelf and the 2 deawers.

What's the big deal? Any 78 year old woman can do it.

0. As a safety precaution, unplug the range or hit the relevant fuse breaker before you start. You might also want to grab a flashlight. Definitely do not try to do this while the oven is hot.
1. Pinch the wire over the light bulb cap to remove it. This is inside the oven at the back.
2. Pop off the hemispherical glass cap.
3. Unscrew the old light bulb, and screw the new light bulb in its place.
4. Put the cap back.
5. Secure the cap by putting the wire back in its slots on the cap.

No tools needed, the cap is just held in place with pressure from the wire.

Turned the wire protector to the side. Turned out the old bulb and replaced it with the new. Turned the wire protector back in place and I'm like new.

replaced lights in refrigirator and freezer

I followed the directions on the site for the center slide replacement. I had actually called a local store and had him order the first part. It took several days and then I started searching online and found this site.Then I ordered the second part on line and to my surprise it arrived the next day. I was fortunate enough to have lived only about 70 miles from the distributer.Following the directions I found here is how I attempted the initial repair. With the vegetable bins out fo the bottom, I removed the plate covering the front frame by gently prying it off. Then I removed the two screws to losen the bar and lifted out the glass shelf. I didn't have much difficulty removing the frame since the front piece support for the slide rail that fit into the frame was already broken. I also had to loosen the screws on the back rail. I removed the entire frame and then replaced the side rail reinserting it into the end caps. I replaced the back screws and then the front ones .I replaced the glass shelf and then the cover cap for the shelf.
The only problem I encountered was that I couldn't seem to get the back screws really tight and I don't know why.

I pulled out the shelf and removed the 2 screws holding the broken side rail to the shelf frame. I then screwed the new rail in and set the shelf back in.

Took out shelf & brackets. Removed plastic shelf. Unscrewed broken bracket & screwed in new bracket.
Put back in & replaced the shelf.

removed produce drawers, removed center piece front cover, removed glass shelf, removed broken drawer slide rail - unscrewing where attached in the rear of the refrigerator. Also removed screw from centerpiece where broken drawer slide rail was attached. reassembled all very quickly....saved myself having to buy another refrigerator by doing this simple repair.

I had to remove the glass shelve, the two drawers, and the middle rail. Once I did that, I slide the unit out together. I placed the unit on the floor and removed the one screw located on the far backside of the unit. I had to remove a slip cover (it had the kenmore logo and the writting on it) it was a snap on, so no problem. Glad it was not gluded on. After the old part was removed, I put the new part on. Put the two screws back on and snap the cover back on. Then I put the whole unit back in. This included the glassshelve and drawers. The process was pretty easy. Good luck with your change.

Took out both draws and glass shelf, removed the entire lower shelf housing. I snapped off the front rail aluminum face to expose the screw. Unscrewed both screws and removed the rail and then just reversed the procedure to put new rail on. It was the most cost effective way of doing it. All the pieces are there on the GE website as long as you know the model number. You will save a lot of money by doing it yourself.

Easy