Your coupon for will be reflected when you check out!
✖
Your coupon for
✖
Hello!
You're visiting the PartSelect site in U.S.
Would you like to shop on the Canadian site?
Stay on this site
Go to Canadian site
✖
Model Number Locations
1Select Category Type
Select Category Type
2Select Product Type
Select Product Type
3Select {MODEL} Type
Select {MODEL} Type
Sample Model Number Tags
Model numbers can be made up of numbers (1005400, for example) or a combination of letters and numbers (LAT1000AAE). The model number will most likely appear on either a paper sticker or a metal plate. Your appliance's model number tag may look similar to the sample model number tags shown here (model number highlighted in yellow):
406777-0114-B1 Briggs and Stratton Engine - Overview
Save your modelModel Saved!
Save your model for later to make things easier.
Model has been saved to My Models. If you're not signed in, your lists are available on this device and will expire within 30 days.
Model has been saved to My Models.
This is a replacement push rod for your lawn tractor engine. It is made of aluminum and is the push rod used for the exhaust valve. Occasionally, the push rod in your engine can become damaged, and wi...
This is a replacement steel push rod for your lawn tractor engine. The engine will have two push rods; one made of steel, and one made of aluminum. This part is made of steel and is approximately 6 in...
This OEM Seal-Oil (PTO Side), also called the Oil Seal, is a Black, Nitrile Rubber, 2/14 O.D., individually sold part which is installed using a Seal Puller. Customers rate the installation difficulty...
$7.88
In Stock
Order now and your part arrives in 2-3 business days!
This is a replacement cylinder head gasket for your small engine. The gasket is approximately 5 inches in length and 5 inches in width at its longest and widest points. The gasket creates a seal, and ...
$26.91
In Stock
Order now and your part arrives in 2-3 business days!
The Oil Seal is a manufacturer-approved rubber part which provides a seal between the crankcase and crankshaft by attaching around the axle shaft on the crankhouse housing. Installation is rated as "M...
$6.59
In Stock
Order now and your part arrives in 2-3 business days!
This is a replacement cylinder head kit for your small engine. It contains everything you will need to replace a damaged cylinder head. This is a 12-piece kit that is sold as a unit. This is an OEM pa...
The Seal-O Ring, also known as the gasket, is red in color, made of rubber, and is an OEM part that requires some skill to replace. This part is designed to create a seal between the carburator and ma...
This genuine crankcase gasket is used on small lawn and garden engines. Its purpose is to make an air tight seal so that no air/oil leakage occurs. Over time this gasket will deteriorate and will need...
$41.86
In Stock
Order now and your part arrives in 2-3 business days!
about 6 hours to tear down and replace don't do it in the hot sun needed more breaks takes longer, but the new factory heads did it started up 185 lbs of compression almost back to new, so much more power than old one's. FYI take off the motor cover every year clean out the debris (grass-mouse nest- and oil) it blocks the air and COOKS
... Read moreTHE HEAD it only takes short time and will make that motor last a little longer but it is a BRIGGS engine
Clean engine with a Gunk type product. Remove valve cover. Loosen bolts and remove old cylinder head. One bolt is located inside valve cover area. Remove old gasket and inspect and clean that surface. Attach new head with new gasket using existing bolts. Torque to 18'#s with a cross type pattern. Attach new rocker arms and push rods. Set
... Read more valve clearance to .004 - .006. Attach valve cover with gasket. Check oil level. Start and let it warm up. Let cool remove cover then check valve clearance again. Replace cover.
I removed the fan shroud, the carb/manifold as an assembly,turned the carb upside down and removed the fuel bowl. I replaced only one jet. Not until this moment did I discover their were two jets in this nikki carb. I now have a second jet ordered and will install it Friday,hopefully. These jets are two different part numbers as one is a
... Read more left jet and the other is a right one. Be careful when opening the fuel bowl as these jets are held in their bores by small O-rings, and nothing else. The brigg's and Stratton part numbers are 791501 for the left jet and 791502 for the right.
