5KPM5BER4 KitchenAid Mixer - Overview
Sections of the 5KPM5BER4
[Viewing 5 of 5]
Keep searches simple, eg. "belt" or "pump".
Dryer Retaining Ring
PartSelect #: PS11746909
Manufacturer #: WP9703438
This part is a retaining ring, sometimes called a retaining clip, that holds the drum support roller onto the shaft of a dryer. It is made entirely of metal and measures less than an inch in diameter....
$7.00
In Stock
Mixer Motor Brush
PartSelect #: PS11753983
Manufacturer #: WPW10380496
Used on Stand Mixers. Sold Individually.
$9.92
In Stock
Mixer Worm Gear
PartSelect #: PS11748374
Manufacturer #: WPW10112253
This worm gear is an inch and a half in diameter. It is used for some of Whirlpool's brands of mixers.
$18.85
In Stock
Mixer Flat Beater
PartSelect #: PS11722956
Manufacturer #: W10807813
This flat beater is used on stand mixers. It is dishwasher safe, however, should only be washed in the upper rack. The Flat Beater is used to mix batters and light doughs. Should the coating become da...
$27.28
In Stock
Mixer Wire Whip
PartSelect #: PS11757305
Manufacturer #: WPW10731415
This wire whip attaches to your stand mixer and is used for whipping food products. It is made of metal wire and is one of several attachments that you can add to your mixer. If you attempt to start y...
$32.93
In Stock
Mixer Worm Gear & Bracket
PartSelect #: PS11740516
Manufacturer #: WP240309-2
Used for Kitchenaid Mixers.
$41.95
In Stock
Mixer Thumb Screw
PartSelect #: PS11747009
Manufacturer #: WP9709194
This part is used with the stand mixers attachments, as well as to hold the end cap to the front of the mixer.
$26.95
In Stock
Mixer Speed Control Plate
PartSelect #: PS11748567
Manufacturer #: WPW10119326
Used in Mixers.
$22.95
In Stock
Mixer Retaining Pin
PartSelect #: PS11746974
Manufacturer #: WP9707223
This part works in conjunction with the worm and bevel gear.
$9.45
In Stock
Mixer Transmission Case Gasket
PartSelect #: PS11742306
Manufacturer #: WP4162324
This part is used with Kitchenaid Mixers.
$21.98
In Stock
Mixer Speed Control Lever
PartSelect #: PS11747016
Manufacturer #: WP9709276
The speed control lever on your stand mixer allows you to adjust the speed that the mixer is running at. The lever is approximately 3.5 inches long, with a black plastic handle at the top. The speed c...
$10.43
In Stock
Mixer Bowl Latch Spring
PartSelect #: PS11740846
Manufacturer #: WP3182857
Used on stand mixers to help keep the bowl in place.
$10.78
In Stock
Questions And Answers for 5KPM5BER4
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Symptoms of the 5KPM5BER4
[Viewing 2 of 2]
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Speed Control Lever KNOB BROKEN
Pulled the Knob off of the new Lever then pressed it on the old Lever. I had to order the whole lever because it was the part nearest the knob in the illustrated parts break-down. I RECOMMEND THAT THE KNOB BE ADDED TO THE ILLUSTRATED PARTS BREAK-DOWN.
Parts Used:
-
Robert from Minot, ND
-
Difficulty Level:Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Pliers
154 of 199 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
motor would run but mixer wouldn't operate: broken worm gear
My girlfriends' stand mixer failed when the accessory drive cap fell into the mixing bowl and jambed the beater, spliting the worm gear. The teeth on this gear are made of nylon and are molded to an aluminum center. This part is designed to fail in situations like this, saving the more expensive transmission parts. Following a repair manu
... Read more
al I found online, I first removed the rear cover and pulled out the cord strain relief out from the base. Next I removed the drip cup from around the base of the planetary drive. I then used a pin punch to drive out the pin holding the planetary to the center shaft and removed the planetary. The unit was then inverted and I removed 4 screws holding the bottom cover to the gear case, and the 5 screws from around the planetary drive. The bottom cover was then lifted off. Three screws holding the worm gear bracket in place were then removed and the worm gear assembly lifted out. A small pin holds the worm gear to the shaft. I drove this out with a small pin punch and the shaft and worm gear were then removed. There is also a thrust washer on this shaft, and it's location is important. Make a note for re-assembly. The new gear was installed and the entire process reversed for re-assembly. A successful repair completed! My girlfriend would have replaced this $200 appliance, but I was able to repair it for less than $30 including shipping.
Read less
Parts Used:
-
Raymond from Shirley, MA
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Screw drivers
85 of 91 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Mixer was making clunking sounds and shaking
I removed screws in a sequence that I felt wouldn't further damage the mixer until I had it completely unassembled. When I found the broken worm gear, I went online to find a part. I found an exploded view, but the part numbering was old, and the salesperson couldn't tell me what the worm gear and bracket assembly consisted of, as I only
... Read more
wanted the worm gear. After trying to drive the pin out of the assembly, and failing, I decided to back online and see if anyone else had a photo of the assembly. Luckily (and wisely) PartSelect,com did and that answered any questions I had. The price was better, too. Reassembly of the mixer was a cinch with the exploded view. It's working like new, and we're hoping for another 35 years of service from it! Thanks.
Read less
Parts Used:
-
Robert from Minden, NV
-
Difficulty Level:Easy
-
Total Repair Time:1- 2 hours
-
Tools:Screw drivers
88 of 104 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!