74814 Toro - Overview
Models starting with 74814
Click on the best match to narrow your results.
Keep searches simple, eg. "belt" or "pump".
Aluminum Push Rod
PartSelect #: PS9073139
Manufacturer #: 690982
This is a replacement push rod for your lawn tractor engine. It is made of aluminum and is the push rod used for the exhaust valve. Occasionally, the push rod in your engine can become damaged, and wi...
No Longer Available
Steel Push Rod
PartSelect #: PS9062983
Manufacturer #: 690981
This is a replacement steel push rod for your lawn tractor engine. The engine will have two push rods; one made of steel, and one made of aluminum. This part is made of steel and is approximately 6 in...
$8.91
Special Order
Engine Oil Seal
PartSelect #: PS9151828
Manufacturer #: 795387
This OEM Seal-Oil (PTO Side), also called the Oil Seal, is a Black, Nitrile Rubber, 2/14 O.D., individually sold part which is installed using a Seal Puller. Customers rate the installation difficulty...
$7.88
In Stock
Engine Cylinder Head Gasket
PartSelect #: PS9067184
Manufacturer #: 693997
This is a replacement cylinder head gasket for your small engine. The gasket is approximately 5 inches in length and 5 inches in width at its longest and widest points. The gasket creates a seal, and ...
$26.91
In Stock
Cylinder Head
PartSelect #: PS9152257
Manufacturer #: 796231
This is a replacement cylinder head kit for your small engine. It contains everything you will need to replace a damaged cylinder head. This is a 12-piece kit that is sold as a unit. This is an OEM pa...
$262.97
Special Order
Engine O-Ring
PartSelect #: PS9294749
Manufacturer #: 691917
The Seal-O Ring, also known as the gasket, is red in color, made of rubber, and is an OEM part that requires some skill to replace. This part is designed to create a seal between the carburator and ma...
$4.99
Special Order
Lawn Mower Crankcase Gasket w/Bolts
PartSelect #: PS11829358
Manufacturer #: 594195
This genuine crankcase gasket is used on small lawn and garden engines. Its purpose is to make an air tight seal so that no air/oil leakage occurs. Over time this gasket will deteriorate and will need...
$41.86
In Stock
Engine Governor Gear
PartSelect #: PS9151758
Manufacturer #: 793338
Ensure smooth and balanced operation of your Briggs and Stratton engine with this exceptional Gear Governor. It's intricately designed to maintain control over the speed of the engine, contributing to...
$30.58
Special Order
Exact Part matches for your search term
[Viewing 1 of 1]
Owner's manual
This part number matches the current model number 74814
PartSelect #: PS12498802
Manufacturer #: 74814
No Longer Available
Common Symptoms of models starting with 74814
[Viewing 1 of 1]
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
the head blew a vaulve guide destoying push rods
about 6 hours to tear down and replace don't do it in the hot sun needed more breaks takes longer, but the new factory heads did it started up 185 lbs of compression almost back to new, so much more power than old one's. FYI take off the motor cover every year clean out the debris (grass-mouse nest- and oil) it blocks the air and COOKS
... Read more
THE HEAD it only takes short time and will make that motor last a little longer but it is a BRIGGS engine
Read less
Parts Used:
-
Robert from WHITMAN, MA
-
Difficulty Level:Easy
-
Total Repair Time:More than 2 hours
30 of 41 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Engine quit due to valve guide sliding out causing rocker arm to be immovable resulting in bent push rods.
Clean engine with a Gunk type product. Remove valve cover. Loosen bolts and remove old cylinder head. One bolt is located inside valve cover area. Remove old gasket and inspect and clean that surface. Attach new head with new gasket using existing bolts. Torque to 18'#s with a cross type pattern. Attach new rocker arms and push rods. Set
... Read more
valve clearance to .004 - .006. Attach valve cover with gasket. Check oil level. Start and let it warm up. Let cool remove cover then check valve clearance again. Replace cover.
Read less
Parts Used:
-
D from HUNTSVILLE, AL
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver, Socket set
14 of 17 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
governor not working
Had to pull the engine off the rider mower. Drained the oil took shield off the flywheel. Set it upside down on a 5 gal bucket. Took a 7/16 hand wrench to remove governor lever from bottom of engine. Left it in its location. Pulled 10 1/2 " bolts. Split engine case. Found the old governor had broke into pieces. Had to use a magnet t
... Read more
o remove all the pieces. Removed the small clip and removed gear. Lubed shaft slid new on put new clip on. Lined governor weights with center piece tapped it in place very lightly. Cleaned gasket flanges pulled the shaft seal. Used the old seal as a seal driver. When putting the cover back on make sure the seal dont roll out. Take a mini screwdriver and tuck it in around shaft. Put bolts back in and tighten like instructions
Read less
Parts Used:
-
rodney from MUSCATINE, IA
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:More than 2 hours
-
Tools:Screw drivers, Socket set
13 of 22 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!