Models > 9114398611

9114398611 Kenmore Cooktop - Overview

Sections of the 9114398611

[Viewing 5 of 5]
Keep searches simple, eg. "belt" or "pump".
Drip Bowl - 8 Inch – Part Number: WB32X106
Drip Bowl - 8 Inch
★★★★★
★★★★★
(15)
PartSelect #: PS244696
Manufacturer #: WB32X106
Drip bowls are located under the heating elements and catch grease and spills that come from cooking on your stove top. If your drip bowl is damaged or rusted, it could allow grease to drip inside you...
$22.05
  In Stock
Surface Burner - 8 Inch - 2100W – Part Number: WB30X253
Surface Burner - 8 Inch - 2100W
★★★★★
★★★★★
(4)
PartSelect #: PS244014
Manufacturer #: WB30X253
This part is the replacement surface burner or element for your range. It is approximately 8 inches in diameter, and 2100 watts. The surface burner connects to the power source and when it is turned o...
$63.02
  In Stock
Surface Burner Terminal Block Kit – Part Number: WB17X210
Surface Burner Terminal Block Kit
★★★★★
★★★★★
(6)
PartSelect #: PS232606
Manufacturer #: WB17X210
This is a surface burner terminal block kit, also known as range surface element receptacle, for an oven, range, or stove. The kit comes with the terminal block, mounting clip, and wires. This surface...
$78.28
  In Stock
Ignitor Mounting Screw – Part Number: WB1X1293
Ignitor Mounting Screw
★★★★★
★★★★★
(2)
PartSelect #: PS234519
Manufacturer #: WB1X1293
Sold Individually.
$9.63
  In Stock
Rolled Terminal Surface Unit - 6" - 1250W – Part Number: WB30X254
Rolled Terminal Surface Unit - 6" - 1250W
★★★★★
★★★★★
(1)
PartSelect #: PS244015
Manufacturer #: WB30X254
$60.22
  In Stock
Screw – Part Number: WB1M1
Screw
★★★★★
★★★★★
(1)
PartSelect #: PS234320
Manufacturer #: WB1M1
Sold Individually.
$7.77
  In Stock
Surface Element Switch – Part Number: W10900107
Surface Element Switch
★★★★★
★★★★★
(3)
PartSelect #: PS12070192
Manufacturer #: W10900107
A surface element switch, also known as a burner/infinite switch, is a device used to control and regulate the heat output of the burners on a stovetop or cooktop. This switch is controlled with a kno...
$52.68
  In Stock
Element Center Medallion – Part Number: WB31X5021
Element Center Medallion
PartSelect #: PS244486
Manufacturer #: WB31X5021
This medallion is located in the middle of the surface burner.
$7.17
  Special Order
Light Switch – Part Number: WB24X415
Light Switch
★★★★★
★★★★★
(1)
PartSelect #: PS237171
Manufacturer #: WB24X415
$37.86
  In Stock
"SCREW-6-32T 6-20 X 3/8" – Part Number: WB1X1118
"SCREW-6-32T 6-20 X 3/8"
PartSelect #: PS234415
Manufacturer #: WB1X1118
$8.06
  Special Order
AIR FILTER – Part Number: WB26M4
AIR FILTER
PartSelect #: PS237614
Manufacturer #: WB26M4
  No Longer Available
TERMINAL – Part Number: WB17M8
TERMINAL
PartSelect #: PS232547
Manufacturer #: WB17M8
  No Longer Available

Questions And Answers for 9114398611

We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.

Common Symptoms of the 9114398611

[Viewing 2 of 2]
Element will not heat
Fixed by
these parts
Fixing Fixing Fixing
Show All
Little to no heat when baking
Fixed by
these parts
Fixing
Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
There was no heat on the coils.
I opened the lid, and found that the terminal blocks were burnt, the wires were melted. I ordered one set of terminal block to replace the burnt one, and it worked. Before I started, I shut off the electricity in the whole house to be safe.
Parts Used:
Surface Burner Terminal Block Kit
  • Shaohui from East Lansing, MI
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Pliers
48 of 52 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Surface burner coil did not work.
TURN OFF ALL POWER TO KITCHEN. Took off all burner coils and plates below them. Lift hood. Locate part. Remove old part and replace with new part in same way as was previously installed. The wire that comes with the kit is actually too much wire, but just arrange it the best you can and leave it....no big deal. I didn't have a magnet, but needed one. The wire from burner coil to switch runs through a harness which is screwed on to the body of the oven (below the range). Be careful NOT to drop it behind oven when taking it out. I dropped it and took forever to get it. That turned a 20 minuate job into an hour and a half. Otherwise this is an easy job that anyone can do. Refrigerator compressor is next. Have fun.
Parts Used:
Surface Burner Terminal Block Kit
  • Gregory from Mont Belvieu, TX
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Nutdriver, Screw drivers, Socket set
23 of 33 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Large burner would not heat
I ordered the wrong part to start with. (READ CAREFULLY!) I reordered the correct part and it was simple. I unpluged the old element, plugged in the new one replaced the drip pan and trim ring and we were back cooking.
Service was fast, lady I spoke with on the phone to exchange parts was knowegable and nice. Great people to deal with.
Parts Used:
Surface Burner - 8 Inch - 2100W
  • Charles from Carthage, NY
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Nutdriver
5 of 6 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!