CCG2523W Jenn-Air Cooktop - Overview
Sections of the CCG2523W
[Viewing 3 of 3]
Keep searches simple, eg. "belt" or "pump".
Dryer Screw
PartSelect #: PS11746840
Manufacturer #: WP90767
This screw is sold individually.
$7.95
In Stock
Spark Igniter
PartSelect #: PS11744544
Manufacturer #: WP7432P109-60
This part creates the spark that lights the gas and starts the burners.
$51.42
In Stock
Range Burner Pan Seal Large
PartSelect #: PS11743854
Manufacturer #: WP71001670
This large pan seal is approximately eight inches in diameter. It is all black in color and it is made entirely of rubber.
$51.42
In Stock
Burner Cap - Large
PartSelect #: PS11744159
Manufacturer #: WP74007200
Sold individually.
No Longer Available
Range Burner Pan Seal Small
PartSelect #: PS11743853
Manufacturer #: WP71001669
This small burner pan seal is approximately six inches in diameter. It is all black in color and is made entirely of rubber.
$58.16
In Stock
Range Mounting Nut
PartSelect #: PS11743922
Manufacturer #: WP7103P178-60
Sold individually.
$9.95
Special Order
Burner Knob
PartSelect #: PS2077742
Manufacturer #: 71002373
Sold Individually. This knob accepts a D-shaped shaft.
No Longer Available
REGULATOR
PartSelect #: PS12074765
Manufacturer #: W11106948
This pressure regulator is three inches long. It is made of metal, but has a blue plastic plug on each end. This regulator sits below a gas range's control panel.
$121.14
In Stock
Valve Screw
PartSelect #: PS3651486
Manufacturer #: W10491986
Part might differ in appearance, but functions same as original. Sold individually.
No Longer Available
Manuals & Care Guides for CCG2523W
Click to downloadQuestions And Answers for CCG2523W
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Symptoms of the CCG2523W
[Viewing 2 of 2]Will Not Start
Fixed by
these parts
these parts
Show All
Gas igniter glows, but will not light
Fixed by
these parts
these parts
Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
stove top gas burner ignitor only flicks but does not light burner
If you have a burner that begins to constantly flick without lighting, and/or flicks while you are lighting another burner, it is likely time to order a new ignitor. Once received, we first lifted the burner support rack, then the burner cap, then unscrewed the nut holding the metal bracket that holds the ignitor in place (years ago we h
... Read more
ad to "soak" the nut with a loosening spray prior to being able to unscrew it, so since then we do not tighten the nuts too tightly so that each nut is easy to unscrew by hand or with pliers if necessary). The previous steps allow one to lift the burner ignitor up and out of its resting hole. It will be connected to the electric wiring via a plastic connector. All one has to do is pull the wiring away from the ignitor and then push it up into the new ignitor. The plastic connector protects you from touching the live ends of the wiring. Voila! The burner lighted successfully.
Read less
Parts Used:
-
Marlene from Dana Point, CA
-
Difficulty Level:Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Pliers
12 of 15 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Conversion back to natural gas From propane
I converted the cooktop from propane to natural gas, the parts I was told I needed were the incorrect parts. I called because I was not sure about the listed parts. I was helped over the phone but recieved the LP parts. The flame was very low, and i found the orifices I replaced were the same parts I just took out.I contacted Parts sele
... Read more
ct and they were helpful and credited my purchase without any hestitation.Once the new orfices were recieved it was easy to install. I recommend using a nut driver with sticky tape to go the orifice holder after the venture is removed. You do not have to disassembe the stove as long as you don't drop the part. Changing the regulalor was also very easy by removing the gold nut and pulling the white pin out and flipping it over to Nat. The flat side of the pin is labeled LP or NAT. Then just screw the nut back in and tighten. The LP orifices are labeled on the side 0.65, 0.69, and 0.70 the natural gas orifces are colored black, silver , and red. It would be just as easy to go from Natural gas to LP!
Read less
Parts Used:
-
Robert from Mullica Hill, NJ
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver, Wrench set
3 of 9 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Treads on holder were stripped
Needed to remove all 4 burners to repair
one, but it went without a hitch.
Thanks to your exacting and clear diagrams, we were able to locate the correct parts
We called JennAire, but they were unable to
find the part..
It was delivered in a timely fashion and
we were able to finish the job in abo ... Read more ut
3 hours. thanks
one, but it went without a hitch.
Thanks to your exacting and clear diagrams, we were able to locate the correct parts
We called JennAire, but they were unable to
find the part..
It was delivered in a timely fashion and
we were able to finish the job in abo ... Read more ut
3 hours. thanks
Read less
Parts Used:
-
Judith A. from Elizabeth, IL
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Socket set
1 of 3 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!