DCCB330GT0WC Whirlpool Dryer - Overview
Sections of the DCCB330GT0WC
[Viewing 1 of 1]
Keep searches simple, eg. "belt" or "pump".
Dryer M-Series Coil Kit
PartSelect #: PS334310
Manufacturer #: 279834
When the igniter reaches a high enough temperature, these coils (Coil Valve, Dryer Gas Valve Coil Kit, Dryer Valve Coil Kit, Gas Valve Solenoid) work together to open the gas valve and allow the gas t...
$27.28
In Stock
Dryer Door Handle (White)
PartSelect #: PS9494490
Manufacturer #: WE01X20419
This part is on the outer door of the dryer.
$30.95
In Stock
Dryer Lint Filter w/Frame
PartSelect #: PS266269
Manufacturer #: WE18X54
This part may differ in appearance, but functions same as original.
$70.51
In Stock
Dryer Door Strike
PartSelect #: PS266893
Manufacturer #: WE1X1192
TThe door strike for your dryer is mounted on the dryer frame that the door shuts onto. It fits into the door catch on the door and keeps the door closed. If the door strike is damaged or missing, the...
$13.95
In Stock
Rear Drum Bearing
PartSelect #: PS267865
Manufacturer #: WE3X75
This part is the rear dryer drum bearing only. This part helps keep your dryer running smoothly as possible with as little noise as possible.
$14.95
In Stock
Dryer 'm' Series Primary Dual Coil Gas Valve
PartSelect #: PS268153
Manufacturer #: WE4X692
This 'M' series coil is both a boosting as well as a holding coil. It has three terminals.
$42.95
In Stock
Dryer Igniter
PartSelect #: PS12342916
Manufacturer #: WE04X25996
NOTE: Be very careful to not handle the igniter by its gray part as it's very fragile. Hold it by its white tip only.
$56.38
In Stock
Dryer M Series Secondary Coil 2 Terminals
PartSelect #: PS268154
Manufacturer #: WE4X693
This part is the replacement main valve coil for your dryer. It is black and white in color and has 2 terminals. It is approximately 1 inch long and 1 inch wide. The main valve coil opens the gas valv...
$39.95
In Stock
Adjustable Leveling Screw
PartSelect #: PS1021358
Manufacturer #: WE1M642
The adjustable leveling screws on the bottom of your dryer can be screwed in or out to lower or raise the leg level. If one of the leveling screws is stripped, damaged, or missing, you may not be able...
$18.95
In Stock
Front Drum Bearing
PartSelect #: PS267867
Manufacturer #: WE3X77
This front dryer drum bearing does not come with slides.
$75.41
In Stock
Screw
PartSelect #: PS271689
Manufacturer #: WH2X930
This screw is sold individually.
$13.95
In Stock
Drive Motor
PartSelect #: PS1559768
Manufacturer #: WE17X10010
Replaces "T" and "V" style motors. Includes two motor pulleys. If you have an older model dryer, the pulley may be pressed on or held on with a set screw. If pulley is pressed on, a new motor pulley must be ordered.
$150.67
In Stock
Questions And Answers for DCCB330GT0WC
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Symptoms of the DCCB330GT0WC
[Viewing 5 of 5]Noisy
Fixed by
these parts
these parts
Show All
Door won’t close
Fixed by
these parts
these parts
Show All
Not Heating
Fixed by
these parts
these parts
Show All
Marks left on clothes
Fixed by
these parts
these parts
Show All
Door Pops Open
Fixed by
these parts
these parts
Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Dryer ran but would not heat
PartSelect showed seven different possibilities why the dryer wouldn't heat. I removed the two screws to remove the bottom panel and turned the dryer on and noticed that the heating element that ignites the gas was working fine. This meant that it was not getting gas so it could be the gas valve or one of the two gas valve coils which are
... Read more
located on top of the gas valve. I borrowed my neighbor"s ohm meter and touched the two probes on the coils terminals to check for continuity and found that one of the coils read zero. I then took both of the coils out by removing two screws and tested each coil again. One coil read 500-850 and the other read zero. This meant that it was no good so I called for the part and received it in three days. I reassembled the parts and turned the dryer on and it fired up after a few seconds. It works as good as new. The part plus shipping was less than $30. My repairman would have charged me $150-$200. While the dryer was apart I gave it a good cleaning with a vacuum and a toothbrush in delicate areas. I also removed and cleaned the lint trap housing by removing two nuts. I didn't know much about gas dryers, but thanks to PartSelect I easily fixed it myself.
Read less
Parts Used:
-
Gary from Haverhill, NH
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver, Screw drivers, Socket set
411 of 470 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Dryer flame goes out after about 8-minutes from start and won’t work again until a 15-minute rest.
There was no problem with lint build-up within the dryer & the exhaust vent. I removed the gas cycling thermostat & thermal fuse from system & dryer still was not operating correctly. The radiant sensor & hi-limit thermostat both seemed to be operating correctly. That left either of the two coils as the culprits. I replaced both coils
... Read more
& the problem was corrected.
Read less
Parts Used:
-
andy from Bethesda, MD
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Screw drivers
210 of 238 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Timer wasn't working (New Timer)
Timer wasn't working on the regular cycle so I replace it with a new one from partselect. It still wasn't working so I ordered and replace the cycling thermostat, the thermal fuse I also cleaned the vent and dryer it still didn't work so I read the diagram for the electrical and found that a coil for the gas valve is line with timer. I or
... Read more
dered the coils for the valves, replaced both valves and tested the dryer and it work just like when I first bought the appliance.
Read less
Parts Used:
-
Joaquin from Las Vegas, NV
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver
166 of 208 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!