DOP36M86DPM (0051) Samsung Range - Overview
Sections of the DOP36M86DPM
[Viewing 1 of 1]
Keep searches simple, eg. "belt" or "pump".
Thermostat
PartSelect #: PS4226434
Manufacturer #: DE47-20037A
This is a high limit thermostat designed for microwaves, ranges and ovens. Made of plastic and metal, this thermostat is designed to open the electrical circuit for your appliance when it reaches a sp...
$26.95
On Order
Rubber Cushion
PartSelect #: PS4241222
Manufacturer #: DG73-00003A
This rubber cushion is supplied by the original manufacturer and has a shaft approximately 1 inch long. The cushion acts as a layer of protection between the oven door and oven frame/cavity. It preven...
$6.95
In Stock
Convection Fan Motor (Lower)
PartSelect #: PS11735747
Manufacturer #: DG31-00005C
This genuine OEM left-threaded convection fan motor is responsible for spinning the fan blade, ensuring even circulation of hot air within your oven for consistent cooking. It is typically located beh...
$136.95
On Order
Temperature Sensor
PartSelect #: PS4240744
Manufacturer #: DG32-00004C
The temperature sensor, also referred to as a thermostat, probe, or thermistor sensor, is responsible for measuring the temperature inside your oven. It is a platinum-resistance sensor with a resistan...
$137.95
In Stock
Hexagon Nut Cap
PartSelect #: PS4133540
Manufacturer #: 6021-001211
This hexagon nut cap, also known as a nut cover cap, is a nylon-insulated cylindrical cap with left-hand threads and a 4mm thread size, for counterclockwise tightening. It is sourced from the original...
$16.95
On Order
Burner Cap
PartSelect #: PS11720685
Manufacturer #: DG62-00137A
The Samsung Burner Cap - Small is a sturdy and durable component, perfect for frequent use in your kitchen range. Crafted from heat-resistant materials, it is designed to promote even cooking and prot...
$81.95
In Stock
Terminal Block Assembly
PartSelect #: PS4241550
Manufacturer #: DG96-00173A
This terminal block assembly is designed for use within various models of ranges and is sold as an individual OEM part without any other hardware included. Terminal blocks are responsible for receivin...
$71.95
In Stock
Flange Nut
PartSelect #: PS4226726
Manufacturer #: DE60-30016A
This flange nut is designed for use within various cooking appliances like ranges, microwaves and wall ovens. Flange nuts are typically used to evenly distribute pressure across its application surfac...
$6.95
In Stock
Questions And Answers for DOP36M86DPM
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Symptoms of the DOP36M86DPM
[Viewing 2 of 2]Door won’t open after self cleaning cycle
Fixed by
these parts
these parts
Show All
Oven not heating evenly
Fixed by
these parts
these parts
Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Oven shut off during self clean cycle and door stayed locked.
I took off the back cover after I looked at youtube similar problems. Then removed the little thermostat and un hooked the 2 wires. I looked up the part and after is was delivered couple days later I connected the 2 wies and after putting the back cover on the oven was back to normal. Was such an easy repair and the part was only $11.
Parts Used:
-
Uwe from FORT COLLINS, CO
-
Difficulty Level:Very Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
16 of 33 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Bearing went out on the fan
Slide out the stove. Unplug the electricity. Remove the back panel with a screwdriver. Then go inside the oven and remove the two Philips head screws holding the fan cover. Then remove the nut holding the fan. Note, it is a left handed nut, so turn it right to loosen it. Pull off the fan. Return to the back and remove the nut and two scr
... Read more
ews that hold the fan. The fan slides right out. The only problem I had was that the electrical contacts on the new motor were wider than the original. I had to break the plastic so I could separate the wire leads, so that they would fit the new motor. Works like a charm.
John
John
Read less
Parts Used:
-
John from NASHVILLE, TN
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Screw drivers, Socket set
6 of 12 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
upper fan motor bad
My repair went terrible as I was sent the wrong motor 2 times. My stove sat in the middle of my small kitchen for 2 weeks. Finally the 3rd was the correct one except I didn't have the right nut so I waited another day for that to be sent. Everything working good now, I just hope the bottom fan doesn't go out after this experience.
Parts Used:
-
SUSAN from DAVISON, MI
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:More than 2 hours
-
Tools:Screw drivers, Wrench set
1 of 8 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!