Your coupon for will be reflected when you check out!
✖
Your coupon for
✖
Hello!
You're visiting the PartSelect site in U.S.
Would you like to shop on the Canadian site?
Stay on this site
Go to Canadian site
✖
Model Number Locations
1Select Category Type
Select Category Type
2Select Product Type
Select Product Type
3Select {MODEL} Type
Select {MODEL} Type
Sample Model Number Tags
Model numbers can be made up of numbers (1005400, for example) or a combination of letters and numbers (LAT1000AAE). The model number will most likely appear on either a paper sticker or a metal plate. Your appliance's model number tag may look similar to the sample model number tags shown here (model number highlighted in yellow):
Model has been saved to My Models. If you're not signed in, your lists are available on this device and will expire within 30 days.
Model has been saved to My Models.
The roller assembly is attached to the upper dishrack of your dishwasher. This is what allows you to easily move your dishrack in and out. The wheel may become damaged over time and will not allow you...
This is an OEM dishrack roller assembly that fits on the lower rear of your dishwasher rack. This part is sold individually. Check the opposite lower dishrack assembly before ordering in case it needs...
This gasket is a seal for your dishwasher and prevents leaking from occurring. The gasket can become worn down over time and you might notice some discoloration. This indicates a replacement is necess...
Spray arms rotate and spray water to clean the dishes inside the dishwasher tub. This part is located beneath the upper rack. The spray arm is meant to spray water and detergent forcefully over the di...
The silverware basket, used in dishwashers, is located in the lower dishrack. The basket is used to hold eating utensils such as spoons, forks, and knives. If the basket is worn out or broken, it shou...
This clip is designed for use in your dishwasher. If you notice that your original clip is damaged, or the dishwasher is not cleaning dishes properly, you may need to replace it. The clip snaps on to ...
Ask our experts a question about this model and we'll get back to you as soon as possible!
3 questions answered by our experts.
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Bob
May 20, 2024
Bottom full of water after cycle is done…
For model number EIDW6305GS1A
Hi Bob, thank you for the question. We would suggest checking the drain hose for clogging first. If it is fine, the issue could be with the drain pump, part number PS2367927. It removes the water from the dishwasher tub during the drain phase of the dishwashing cycle. You may need to replace it fix the issue. We hope this solves your problem!
Why is the dish washer always warm when we open the door?
For model number EIDW6305GS1A
Hi Russell. The control board may be keeping the heating element on. It may need replacement. Thank you for your question and good luck with your repair.
Why is the dish washer always warm when we open the door? I asked this earlier today and was told that the board could be bad: not a good answer, i downloaded the schematic and it shows the element is switched to 12v low voltage after cycle is complete, I’m assuming this is to keep the tub dry, yes this site is very helpful.
For model number EIDW6305GS1A
Hello Russell,
Thank you for your question. Yes, the element drys the tub and the dishes dry at a lower temperature, and if the door itself wasn't sealed completely the heat could spread to the door itself. However if there aren't any issues with the dishwasher functions or any noticeable leaks, the heat on the door is normal. We hope this helps.
Was this helpful?
Thank you for voting!
< Prev
1
Next >
✖
Ask a Question
Ask our experts a question on this model and we'll respond as soon as we can.
Disconnect from power Unscrewed 4 phillips screws from top of outer door. Unscrewed 2 screws each siide of door. Lower outer door section drops away. Note wiring sequence on dispenser, then disconnect wires. Unscrew 6 screws on dispenser and lift dispenser out.
Place new dispenser in place (note orient
... Read moreation), ann fasten in place with screws, remembering to replace wire retainer on left lower screw. Reconnect wires to dispenser correctly. Slide lower outer door over tabs and secure with the 4 side screws. Ensure lower door is up under control panel and secure with the 4 top screws.
Fill dispenser with detergent, reconnect power and test run while enjoying a cup of tea in celebration of a job well done..
I was able to pull out the top basket were the glasses are put then I lined up the back and the center plastic clip an slid on the center spray arm. It took about 2 miniutes
The only difficultpart was to figure out how to remove the stainless cover from the door. Seems it slides upwards after screws are removed. After that it is self explainatory and goes back together in 5 minutes.
