Parts That Fix Frigidaire Washer Dryer Combo FEX831FS2 Will not drain
Will not drain is a commonly reported symptom for the FEX831FS2 Frigidaire Washer Dryer Combo, and we have put together a full guide
... Read more
on how to fix this. This advice is based on feedback from people who own this exact appliance. We have listed the most common parts for your FEX831FS2 Frigidaire Washer Dryer Combo that will fix Will not drain.
We have included repair instructions, and helpful step-by-step video tutorials. If you are experiencing this issue, not to worry, DIYers just like you have fixed this, and shared their experience to help you!
Read less
Will not drain is a commonly reported symptom for the FEX831FS2 Frigidaire Washer Dryer Combo, and we have put together a full guide on how to fix this.
This advice is based on feedback from people who own this exact appliance. We have listed the most common parts for your FEX831FS2 Frigidaire Washer Dryer Combo that will fix Will not drain.
We have included repair instructions, and helpful step-by-step video tutorials. If you are experiencing this issue, not to worry, DIYers just like you have fixed this, and shared their experience to help you!
Fixes Symptom 82% of time
This is a 120 volt, 60 hertz drain pump that is manufactured to remove water from the tub of your washer once your clothes are washed. This part is the pump and motor assembly, which includes a red flapper to prevent drain backflow. You will need to remove the front panel of your washer to access the drain pump. The tools you will need for the repair are a Phillips screw driver, a putty knife, a pair of slip joint pliers, and a 5/16 nut driver. Be sure to disconnect the water supply from your washer before doing the repair. The metal edges on the appliance are sharp, so use work gloves to safely complete the repair.
$
145.45
In Stock
PartSelect Number PS7783938
Manufacturer Part Number 137221600
Replacing your Frigidaire Washer Drain Pump (60hz 120v)
Customer Repair Stories
After a full cycle the washer would not drain the water
After reading the possiblilities of problem, I determined that the drain pump was not working; therefore I ordered a new one. When I opened the washer to replace the part, I found out that the pump was working but the filter was stuffed with pieces of rubber that came out from a rug I washed. Once all the stuff was removed, the washer wor
... Read more
ked just fine. PartSelect was very gracious to accept the returned with not questions asked!! Thanks partSelect.
Read less
-
sara from North Miami, FL
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
84 of 94 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
would't spin all water out or rinse out clothes
uplugged washer took front off washer 2 screws pryed up top pump was mounted with 2 screws and 2 wires took off found change in pump and the fins to pump worn off ordered part off line the wait for part was longer than the amount of time to fix problem and cost of part saved me about $25-35 if I was to buy local worth wait save money and
... Read more
fix problem washes like new spins and drains all water from tub.
Read less
-
kenneth from willard, OH
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver, Pliers, Screw drivers
172 of 210 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Fixes Symptom 13% of time
Mounting bracket on this part replaces old style ( You may need to drill off old bracket before mounting new lock).
No Longer Available
PartSelect Number PS648775
Manufacturer Part Number 134101800
Replacing your Frigidaire Washer Washer Lid Lock with External Safety Switch
Customer Repair Stories
washing machine will not drain or spin
removed upper cover, removed front cover, tested switch with digital VOM, removed and replaced!
2 screws, 4 wires! saved over $100 when compared to a bill from a repair service!
fast shipping too! will recommend others!
2 screws, 4 wires! saved over $100 when compared to a bill from a repair service!
fast shipping too! will recommend others!
-
Heath Harris from Arnold, MO
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
41 of 49 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Lid Lock Assembly broke
The Lid Lock Assembly came super fast! The install would have been flawless, but the "pre-drilled" holes on the new Lid Lock Assembly were way to small. We found that out after we had reconnected the wires and gotten it into place. Aside from that small set back, the install went great! This repair is definitey not one that you would
... Read more
need to pay a repair person to do!
Read less
-
Jenessa from Tacoma, WA
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
75 of 94 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Fixes Symptom 5% of time
This rubber V-style drive belt slips on the motor pulley to bring the basket to the required speed. If you notice a burning rubber smell or grinding noises coming from your washer, your washer does not start, drain, spin properly (will not spin/spins slowly/will not agitate properly), or if your washer shakes or moves during the cycle; check your drive belt for signs of wear and tear. Replace the drive belt if you notice that the belt looks damaged. This OEM part is approximately 35 inches in length, and sold individually.
$
20.95
In Stock
PartSelect Number PS1146950
Manufacturer Part Number 134511600
Replacing your Frigidaire Washer Drive V-Belt
Customer Repair Stories
the belt was all worn out , it make a lot of noise
i took out the two back screws lift the top.
took the two bottom front screws , lifted andtook off the front panel.took off the old belt an intall the new one in a circular motion put the panel and top back on and done.
took the two bottom front screws , lifted andtook off the front panel.took off the old belt an intall the new one in a circular motion put the panel and top back on and done.
-
CARLOS from BEALETON, VA
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Pliers, Screw drivers
26 of 38 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
replace broken drive belt
carefully pry up on front washer top to release plastic keeper pins,remove 2 phillips screws from beneath lower front washer panel,slightly lift upward on panel to release.remove old broken belt,push new belt beneath large tub pulley,put belt on small motor pulley,push back belt tension /idler arm,start belt on large tub pulley,turn tub p
... Read more
ulley by hand to run belt on,release tension on idler arm.replace front panel and lower top.WALAAH!!!! you are done.
Read less
-
rodney from fairfield bay, AR
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
280 of 313 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!