Make sure you haven't got the discount earlier.
Parts That Fix Frigidaire Dishwasher FFBD2406NS7B Not cleaning dishes properly
Not cleaning dishes properly is a commonly reported symptom for the FFBD2406NS7B Frigidaire Dishwasher, and we have put together a full guide on how to fix this. This advice is based on feedback from people who own this exact appliance. We have listed the most common parts for your FFBD2406NS7B Frigidaire Dishwasher that will fix Not cleaning dishes properly. We have included repair instructions, and helpful step-by-step video tutorials. If you are experiencing this issue, not to worry, DIYers just like you have fixed this, and shared their experience to help you!
The Lower Spray Arm is used in your dishwasher to spray water and clean your dishes. If broken there will be visible damage or your dishes may no longer be cleaned properly. If your spray arm is broken (due to general wear or high heat), it should be replaced. Your lower spray arm will be located at the bottom of your dishwasher tub. Check your user manual and model number to ensure this model is right for you. This version is plastic and metal and comes in gray/blue. We recommend you wear work gloves to keep your hands safe when installing and disconnect power to the appliance. You will also want to make sure that you turn off the water supply to your dishwasher. From here, you will want to open the dishwasher, pull out the lower rack and set it aside. Remove the lower wash arm. On each side of the bottom of the spray arm, there are small locking tabs that can be pushed aside using a flathead screwdriver. Once released, the spray arm can easily be pulled off the dishwasher. Put the new lower wash arm in place and push it down to lock it in. Ensure it is spinning freely and does not hit the heating element. Return the lower dish rack into place and then close the dishwasher door.
Replacing your Frigidaire Dishwasher Lower Spray Arm
Customer Repair Stories
Spray arm fell over and melted on the heating element.
-
Inge from Hernando, FL
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
spray arm keeps melting
-
Donna from Madison, OH
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
This spray arm is a genuine OEM replacement part for your dishwasher. This spray arm is for the upper part of your dishwasher. No tools are required for this repair, simple remove the rack stops and upper dish rack, then disassemble the mount and spray arm before installing the new one.
Replacing your Frigidaire Dishwasher Upper Spray Arm
Customer Repair Stories
upper spray arm retainer nut failed
ordered new one from site, was delivered with-in 2 days ( with standard shipping) all 1 piece, took seriously 5 seconds to unscrew by hand and replace!
-
Michael from Hillsdale, NJ
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
The spray arm would fall off during the washing cycle.
-
Roy from Worcester, MA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
This plastic cover and stem assembly helps hold the lower spray arm in place.
Replacing your Frigidaire Dishwasher Lower Spray Arm Support
Customer Repair Stories
Broke nubs off of stem when cleaning
-
Glen from Chicago, IL
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
Lock Down On Stem Stripped
-
Ronnie from Elberfeld, IN
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
This lower spray arm is a genuine OEM part for various makes and models of dishwasher and is sold as an individual part. This part attaches to the lower spray assembly of your dishwasher and the lower spray arm itself clips into this part to facilitate its spinning movement during the washing cycle. To replace it, remove the spray arm by pulling it out, remove the surrounding circular clip and then twist to remove this bit. Made completely of plastic, this part measures approximately 3-inches deep, 2-inches wide, and 3.125-inches tall.
Replacing your Frigidaire Dishwasher Lower Spray Arm Support
Customer Repair Stories
missing bottom spray arm
-
Ashley from Normal, IL
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
spray arm fell off and melted on element
-
Dale from Worley, ID
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
This kit includes the motor and o-rings.
Replacing your Frigidaire Dishwasher Pump Motor Kit
Customer Repair Stories
Water leak behind kick-plate
-
Larry from EDWARDS, CO
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Screw drivers, Socket set, Wrench set
not cleaning, spray arms not working
-
Jeff from Lancaster, PA
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver, Screw drivers, Wrench (Adjustable)
This grommet fits on the spray arm of your dishwasher. This replacement part connects and seals the spray arm to the water hose that supplies water to the dishwasher tub. Be sure to shut off water supply to your appliance before completing this repair. This part is 3 inches in diameter and is off-white in color.
Replacing your Frigidaire Dishwasher Water Delivery Tube Grommet
Customer Repair Stories
Replacing grommet
-
Jack from KENDALLVILLE, IN
-
Difficulty Level:Very Difficult
-
Total Repair Time:More than 2 hours
-
Tools:Pliers, Screw drivers
wrong part
Now i am back at square one with part I don't need and hoping for the part I do need
-
Loraine from HYDE PARK, VT
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
This filter is for dishwashers. The filter removes food particles and debris from the water to prevent the drain from clogging. Follow the instructions in the manual when installing this part.
Replacing your Frigidaire Dishwasher Dishwasher Filter
Customer Repair Stories
dishes not comming out clean
-
JOHN D from ROCKPORT, TX
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:More than 2 hours
Replace filter in dishwasher
-
Gary from NEW KENSINGTN, PA
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
This is an OEM center spray arm, which works with dishwashers.
Customer Repair Stories
The Center Spray Arm was broken
-
YVES from VALLEY STREAM, NY
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
Sold individually.
Replacing your Frigidaire Dishwasher Delivery Tube Gasket
Customer Repair Stories
Spinner fell off of delivery tube.
-
Jeffrey from Rougemont, NC
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Pliers
Dishwasher Leakibng
Unplugged dishwasher and slid it out from cabinet area (be sure to turn off and disconnect water supply)
Followed delivery tube up side of dish ... Read more washer to top of tub and noticed reminents of where water ran down side of tub.
Loosened delivery tube by plastic nut inside of tube and removed. Noticed gasket was partially depleted.
Ordered new gasket, replaced and put everything back together. (Be sure to use teflon tape on water source fitting and tighten firmly). No leaks
-
Eric from Benton, KY
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Pliers, Wrench (Adjustable)
Located at the bottom of the dishwasher, this filter keep large particles of food and foreign objects away from the pump.
Replacing your Frigidaire Dishwasher Filter Base
This dishwasher heating element is not designed to heat the water that enters it, but is designed to maintain the heat of the water that enters the dishwasher. It is located on the bottom of the dishwasher. NOTE: Brass nuts are NOT included. Must be ordered separately.
Customer Repair Stories
Heating Element was corroded.
-
Christopher from EVERETT, WA
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver, Screw drivers, Wrench (Adjustable)
Heating element went out
removed the c-clips holding element underneath
and put new one in. Hard part was figuring out
what was holding the element but since I still
had the schematic drawing we figured it out.
Saved a bunch on a repairman. After watching
my friend install the new eleme ... Read more nt I could probably
do it myself next time.
-
Jane from Port Charlotte, FL
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:30 - 60 mins
-
Tools:Screw drivers, Wrench (Adjustable)
Part is found under the lower spray arm.
Replacing your Frigidaire Dishwasher Drain Trap
Customer Repair Stories
several issues with dishwasher
replaced drain trap and four rack wheels with clips
All parts were expensive for the items.
found cheaper wheels w/clips for much less on another site.
-
Nicholas from KESWICK, VA
-
Difficulty Level:Very Easy
-
Total Repair Time:Less than 15 mins
The single rack roller kit comes with one axle/clip and one wheel/roller. The rack wheel is designed to allow the rack of your dishwasher to roll in and out. If the rack will not complete this task, or you notice that your dishwasher is not cleaning dishes properly, you may need to replace the rack wheel. The single rack roller kit is made of white plastic, and clips to the dishwasher rack with the included axle/clip. Many of our customers have described this repair as easy, and you will not require any tools to complete it. Lower rack roller and bracket assembly, grey. Wheel has been updated. If wheel pictured is not like old one, you may need to replace all wheels.
Replacing your Frigidaire Dishwasher WHEEL & BUSHING ASS
Customer Repair Stories
plastic attachment for wheel to rack had dried and broken
Got to say, I was pretty amazed that I received my order the following day! You guys are wonderful!
-
Marla from Columbia, TN
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
Lower Rack Roller Missing
-
Sandra from Mount Vernon, WA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
This water inlet valve is for dishwashers. Water inlet valve supplies water to the dishwasher. Unplug the dishwasher and shut off the water supply before installing this part
Customer Repair Stories
Unit would not fill with water.
-
Cyril from WAYNESFIELD, OH
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Pliers, Screw drivers
Dishwasher was not filling up at the start of the cycle.
Turned off the breaker for the dishwasher. Turned off the water supply valve. Unscrewed the screws in the panel that hides the parts under the dishwasher. Unscrewed the screws anchoring the dishwasher to the counter. Slid the dishwasher out about a foo ... Read more t. Inlet valve was located on the front left side of the dishwasher. Unclipped the wire harness. Placed a cookie sheet under the water line. Unscrewed the water line from the inlet valve. Unscrewed the two Phillips head screws holding the valve to the dishwasher frame. Got the new part. Put the screws back into the frame. Reconnected the water line and wire harness. Slid the washer back into place. Turned on the water valve. Watched for leaks. Turned the breaker back on and started the cycle. Watched for leaks. Once I saw there weren’t any replaced the screws anchoring it to the counter and replaced the cover on the bottom. That was it! Took me longer to type out the steps than it did to actually do the repair.
-
CHERI from CREEKSIDE, PA
-
Difficulty Level:Very Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers, Wrench (Adjustable)
This grey OEM dishwasher tub gasket is a 73" grey rubber part that creates a seal around the dishwasher to prevent any water leakage during a cycle. If it's damaged or broken, you'll start seeing water leaking out. If broken, it should be replaced. Refer to your model number and user manual to ensure this part is right for you. When making this repair, open the dishwasher door and take out the lower dish tray for better access. Pull out the old gasket, and clean the channel with a rag. Push the new gasket into place into the notch on the door, which you should see upon close inspection, using a flat-head screwdriver for assistance if necessary. We do not recommend cutting any additional length off on the tub gasket if any is present during your repair.
Replacing your Frigidaire Dishwasher Dishwasher Tub Gasket - Gray
Customer Repair Stories
Dishwasher was leaking at the lower left side of the door.
Water leak solved...
-
John from Hummelstown, PA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
dishwasher was leaking water
-
Charles from Milton, FL
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
This is the replacement detergent dispenser for your refrigerator. It is gray in color and is sold individually. It is approximately 8.5 inches long and 3 inches wide. The detergent dispenser stores the detergent until it is ready to be dispensed. If your dishes are not coming clean, or you notice the detergent is still in the dispenser at the end of the cycle, you may have a damaged or malfunctioning detergent dispenser. This is an OEM part sourced directly from the manufacturer.
Replacing your Frigidaire Dishwasher Detergent Dispenser
Customer Repair Stories
Leaked spot free fluid
-
Tim from MARINE ST CRX, MN
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Pliers, Screw drivers
The soap dispenser didn’t dispense the soap
-
Bernard from ACUSHNET, MA
-
Difficulty Level:Very Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
If your dishwasher is leaking or not draining properly, you may need to replace the drain hose. The drain hose connects to the pump located below the lower spray arm and aids in proper dishwasher drainage. This white and black plastic hose is 7.5 feet long. For this repair, you will need either a 1/4-inch or 5/16-inch nut driver, depending on your model. You will need to remove the lower access panel on your dishwasher to complete this repair; it is often easier to remove the dishwasher from the cabinet to do so. Be sure to disconnect the dishwasher from both the power and water supply before completing this repair.
Replacing your Frigidaire Dishwasher Dishwasher Drain Hose
Customer Repair Stories
A hole in the dishwasher dicharge hose.
-
Lee from Columbus, OH
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver, Screw drivers
Drain hose was missing
-
John from Carthage, MO
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers, Wrench set
This dishrack is for dishwashers. The dishrack holds the dishes in place during the dishwashing cycle.
Replacing your Frigidaire Dishwasher RACK ASSEMBLEY LOWER GREY
Customer Repair Stories
Need a replacement bottom rack for the dishwasher
-
Katherine from Clearwater, FL
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
The prongs that hold the dishes were burning off.
-
Richard from PAWLEYS ISL, SC
-
Difficulty Level:Very Easy
-
Total Repair Time:Less than 15 mins