The Lower Spray Arm is used in your dishwasher to spray water and clean your dishes. If broken there will be visible damage or your dishes may no longer be cleaned properly. If your spray arm is broke...
$35.34
In Stock
Order within the next 11 hrs and your part ships today!
This grey OEM dishwasher tub gasket is a 73" grey rubber part that creates a seal around the dishwasher to prevent any water leakage during a cycle. If it's damaged or broken, you'll start seeing wate...
$32.35
In Stock
Order within the next 11 hrs and your part ships today!
The single rack roller kit comes with one axle/clip and one wheel/roller. The rack wheel is designed to allow the rack of your dishwasher to roll in and out. If the rack will not complete this task, o...
$6.88
In Stock
Order within the next 11 hrs and your part ships today!
The heating element nut is used to connect the heating element to the dishwasher tub. If water is leaking from underneath your dishwasher, you may need to tighten or replace the heating element nut. R...
$7.82
In Stock
Order within the next 11 hrs and your part ships today!
This lower spray arm is a genuine OEM part for various makes and models of dishwasher and is sold as an individual part. This part attaches to the lower spray assembly of your dishwasher and the lower...
$11.26
In Stock
Order within the next 11 hrs and your part ships today!
If your dishwasher is leaking or not draining properly, you may need to replace the drain hose. The drain hose connects to the pump located below the lower spray arm and aids in proper dishwasher drai...
$26.66
In Stock
Order within the next 11 hrs and your part ships today!
This door seal is for dishwashers.
Door seal seals the gap between the opening to the dishwasher tub and the outer edge of the door.
After installing the door seal, shut the dishwasher door and ...
$32.27
In Stock
Order within the next 11 hrs and your part ships today!
This door spring is manufactured for a dishwasher door. The door spring applies tension to the dishwasher door so that the door does not drop too quickly when it is opening. If the door drops too quic...
$34.99
In Stock
Order within the next 11 hrs and your part ships today!
The upper dishrack roller and axel kit comes with two pieces, a wheel and an axle. This kit is made for your dishwasher. Both pieces measure to be roughly one square inch each, they are made entirely ...
$4.99
In Stock
Order within the next 11 hrs and your part ships today!
This rail end cap, or dishrack stop clip, is a genuine OEM replacement part for your dishwasher. This part keeps the rack in your dishwasher from sliding out. This is a very easy repair, to complete i...
$7.28
In Stock
Order within the next 11 hrs and your part ships today!
This is a drain pump assembly for various compatible models of dishwashers, that is responsible for draining the water from the dishwasher after every cycle. This drain pump assembly is made of plasti...
$100.36
In Stock
Order within the next 11 hrs and your part ships today!
Questions And Answers for FFCD2413UB3A
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
2 questions answered by our experts.
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Mike
September 23, 2023
Cannot change run mode. Ie stays on heavy wash all the time and heated dry. Does it need a a new contact strip? Machine is two years old.
For model number FFCD2413UB3A
Hello Mike, thank you for contacting us. According to our research, if the unit is stuck on heavy wash or heated dry, then there is an issue with the user interface control board, part number PS12585627. However, before replacing it, unplug the dishwasher or flip the circuit breaker off to the dishwasher and use a hair dryer to heat up the user interface control board. Rub your thumb over the heated dry button and wait 5 minutes for it to cool. Now plug the dishwasher back in and see if the issue clears up. If not, then the entire user interface control board would have to be replaced to resolve the issue. Glad to be of assistance!
Frigidaire dishwasher fills with water but then does not start the wash cycle. It fills and then stops. When I hold in the start button for 3 seconds to cancel, dishwasher drains normally. What could cause this?
For model number FFCD2413UB3A
Hi Chad, thank you for reaching out. Based on the description that you have provided, we would recommend checking the following parts: motor and pump assembly, part number PS12712308, and lower spray arm, part number PS12585623. If checking these does not fix the issue, then you may need to replace the electronic control board, part number PS12585627. We hope this sorts out your problem!
I have had to keep replacing the spray arm on the bottom of my dishwasher which takes like 2 seconds to do.. First you open the dishwasher and than pull the bottom basked forward and reach down and pull the spray arm up and pop the bottom of the spray arm off and put it on the new spray arm and slip it back into the dishwasher over the t
... Read morehing that makes it spin around.. but the tricky part is and I didn't know this and this is why my dishwasher spray arm kept falling over and melting on the heating element.. you have to turn it till it clicks in.. and your done..
I removed old tub gasket, which the door presses against to make a seal, and put the new one in. Flat tip screwdriver was used to gently press gasket in.