Your coupon for will be reflected when you check out!
✖
Your coupon for
✖
Hello!
You're visiting the PartSelect site in U.S.
Would you like to shop on the Canadian site?
Stay on this site
Go to Canadian site
✖
Model Number Locations
1Select Category Type
Select Category Type
2Select Product Type
Select Product Type
3Select {MODEL} Type
Select {MODEL} Type
Sample Model Number Tags
Model numbers can be made up of numbers (1005400, for example) or a combination of letters and numbers (LAT1000AAE). The model number will most likely appear on either a paper sticker or a metal plate. Your appliance's model number tag may look similar to the sample model number tags shown here (model number highlighted in yellow):
Model has been saved to My Models. If you're not signed in, your lists are available on this device and will expire within 30 days.
Model has been saved to My Models.
This OEM-compatible screw is designed for use with many GE dishwashers. Measuring 8-16 HXW and 1/2" in length, this stainless steel screw secures the middle spray arm hub to the upper rack assembly, e...
$13.95
In Stock
Order now and your part arrives in 2-3 business days!
This is a water hose clamp kit for a variety of appliances including dishwashers and washers. This is a genuine replacement part. The kit includes two hose clamps. The smaller of the two is 1 inch in ...
$22.95
In Stock
Order now and your part arrives in 2-3 business days!
Perfect for your GE washer, the Nut Hub is designed to secure the washer hub to the gear case shaft with precision. It plays a crucial part in ensuring the appliance runs smoothly and efficiently. The...
$19.95
In Stock
Order now and your part arrives in 2-3 business days!
Upgrade your washer with the reliable Washer Hub from GE. This essential component, often referred to as the hub nut, offers sturdiness and quality that GE products are known for. Before installation,...
$14.95
In Stock
Order now and your part arrives in 2-3 business days!
Introducing the GE Drain Hose, specifically designed for washing machines. This essential accessory safely transports used water from your washer directly to your house drain, establishing an efficien...
$45.95
In Stock
Order now and your part arrives in 2-3 business days!
Ask our experts a question about this model and we'll get back to you as soon as possible!
1 question answered by our experts.
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Rommel
December 3, 2019
Flashing start button
For model number GTAN8250D0WS
Hello Rommel and thanks for writing.
Unplug the washer for 1 minute from the electrical outlet.
Plug the washer back in and lift and lower the lid 6 times within a 12 second period. You have 30 seconds to start lifting and lowering the lid. ...
The motor has now been reset and is ready for you to start a cycle. We hope this helps. Please contact us anytime.
Was this helpful?
Thank you for voting!
< Prev
1
Next >
✖
Ask a Question
Ask our experts a question on this model and we'll respond as soon as we can.
This procedure was completely different from any other Tub Seal I've done and in my opinion needs 2 people. The first thing to note is that this seal must be removed from the bottom of the outer tub. Also, the top of this machine does not hinge in back. The typical clips are in front, but the back has 2 screws that must be removed. Since
... Read morethe wiring was too involved to completely separate the top from the base, I had to improvise a stand to hold the top while the rest of the process was completed - keep slack on all remaining connected wires. The motor, clutch and bearing plate must be removed from the bottom in order to access the Tub Seal. Below are the steps I did to complete the process: - Remove Control Panel Cover (rear) - Disconnect as many wire harness plugs as possible from Control Board (Note positions for reassembly - pictures work well) - Remove Pressure Switch - Disconnect Detergent and Softener dispense hoses from Machine Top - Rotate top 180 degrees (Flat-Spin) and position so no strain is on the still connected wires. - Remove Tub Cover - Remove Impeller (Agitator) from inside tub. - Remove Tub Nut - Note Left handed Threads (I used 1/2" Drive Impact) - Remove rear Cross Bar from cabinet (Cross Bar must be removed since tub will not fit through opening. Once removed it must be held in place or outer tub will fall) - Remove Inner Tub - This tub is heavy and fluid-balanced. Mine required 2 people to wobble and pull for removal. - Replace Cross bar to keep unit stable - Lay machine on its side - use care not stretch or pull any wires. - Remove motor, (Rotor and Stator) - Remove Clutch and wires - Loosen all wire ties (Use tiny screwdriver to release ties - Do Not remove the tie mount) securing wires to Bearing Plate and push wires to the outside edge of bearing Plate - Remove all screws securing Bearing Plate to Outer Tub - Use flat-head Screwdriver to gently pry Bearing Plate away from outer tub (Quite Heavy - Use Care) - Tub Seal is now exposed on top of Bearing Plate and can now be removed and replaced (Be sure to clean all seal mating surfaces and lubricate with dish soap) - Reverse this sequence in the exact order for re-assembly taking care to reconnect all wiring plugs and ground wires. - During Re-assembly I used Blue Loctite on all bolts securing the Clutch, Stator, and Rotor as I found several very loose on my machine
Secured power and supply lines. Took off rear panel. Labeled all 5 electrical inputs to water valve. Could not get water valve out. Found the 5 hoses that were clamped to the 5 valve inputs by going head first into the washer. Did not order the clamps!!!! Even if we had, we couldn't figure out how to access them. Called appliance guys who
... Read more installed valve and clamps.
