GTS20IBNCWW General Electric Refrigerator - Instructions

After verifying that my water solenoid valve did open and close (I removed the solenoid and put my own 120vac on it and blew through it) and then I verified that I was receiving my 120vac from the ice maker itself I knew my problem was in the ice maker itself. Just removed the mounting screws holding the old ice maker and it lifted out of place after unplugging the unit from electrical connection at the rear of the cabinet. Reversed the process for installation. Power unit up. Bleed air out of the water line feeding the watermaker. Waited a couple of hours and my first cubes where there. Filled up quick! Thanks.

Ordered the complete kit minus the water tap. Should have ordered that also. Install was difficult simply because I was not sure of the style of the fridge. No ident had been left on the unit, so I used the p;ictures in the install kit to decide the proper install. Was very quick and the parts were great. After I went under the house(crawl space) I found an old water tap which broke off in my hand and started spewing water. Replaced everything and it runs great. Nice kit with a lot of instructions. Fantastic ordering fromyour company. Next day delivery was unexpected.

My wife and I decided to tackle this job on a Saturday. The fridge was due for a good cleaning anyway. We pulled it out and shut off the water to the ice maker.
I took out the old ice maker, (two screws and the plug) Then went to the back of the fridge. removed the cardboard cover at the bottom of the frigdge and took the mounting screw out of the water valve. I had a double valve for the no longer working in-door water so I made sure to identify Then installed the new water valve. Note: be sure to check your connections for leaks before mounting the water valve - it is easier to see and fix them !!!! You can leave the water on at this point because the icemaker and water valve will not operate until the icemaker is plugged in. Next choose the right water fill cup, and install the ice maker to the existing screw mounts and plug in the connector. Note: be sure the ice maker is turned off. Start the fridge, let it get cold, then turn on the icemaker.
Overall this is a great multi install package - Don't worry about extra parts because you will have some. If we would have just needed to do the icemaker and not clean the fridge, I could have done it in about an hour.
Overall I would highly recommend this package vs what is available at other retailers for more money. Best Buy has a bargain replacement icemaker but does not have the versatility and completeness of this product. I give this product 5 stars.... dm

By following the instructions in the manual that went with it, I used the parts in the order that the instructions said. The illustrations were very easy and now we dont have to use ice cube trays any longer. Any person without experience that can follow directions can put in an icemaker with the simple to follow instructions that was used in the manual.

Unplugged the old ice maker. Removed the two screws that held it in. Removed the old ice maker and replaced it with the new one. Put back the two screws, plugged it back in and turned on the power switch. It started making and dropping ice in the first 1/2 hour.

I had to call for a appointment for repair with GE Appliance because I thought then it . .was something electrical. The technician came out & checked everything out, turned out it was not electrical, The technician went out to his truck got a light bulb from his truck, put it in & it worked. It cost me $121.00 for trip charge from GE appliance for a light bulb that worked, your light bulbs were defective twice. Very disappointed with your products, cost me alot of money for a good light bulb thru GE appliance

Unplugged the appliance for safety. Removed two 1/4" screws that held the assembly in place. Carefully removed the wire guard that retains the glass shield. Unscrewed old light bulb and replaced with new part. Reversed the steps after cleaning glass cover.

I removed the bin and dumped out all the ice then I took out the two screws holding the icemaker to the freezer wall. I then unplugged the icemaker. Since all of the funnels etc were in place I simply plugged in the new icemaker, installed the two mounting screws, slipped the icemaker in place tightened the screws and turned it on.I'm happy to say the new unit is much faster than theold one. By morning I had a full bin of cubes. Thanks so much for your help.

Ice maker not working. Received my order in 30 hours. (Excellent) After installing ice maker and water valve, I noticed that where the water enters through the freezer to the ice maker spout, there was a frozen spot in the connector. After melting the ice blockage with a hair dryer, the ice maker and water valve began working. No problem since. Unit working perfectly.

0. As a safety precaution, unplug the range or hit the relevant fuse breaker before you start. You might also want to grab a flashlight. Definitely do not try to do this while the oven is hot.
1. Pinch the wire over the light bulb cap to remove it. This is inside the oven at the back.
2. Pop off the hemispherical glass cap.
3. Unscrew the old light bulb, and screw the new light bulb in its place.
4. Put the cap back.
5. Secure the cap by putting the wire back in its slots on the cap.

No tools needed, the cap is just held in place with pressure from the wire.

Turned the wire protector to the side. Turned out the old bulb and replaced it with the new. Turned the wire protector back in place and I'm like new.

replaced lights in refrigirator and freezer

First we removed two screws and removed old icemaker- then replaced with the new one~ made ice within the hour. Simple~ Easy~

The exchange was easy. BUT> Do not discard the three screws or the small patch that covers the one screw at the bottom of the handle. The new handle does not come with screws or that patch. The hardest part was getting the patch off the old handle.

We replaced two old icemakers with two new for less than a local repair company wanted to charge us for ONE. Very easy to install, hardest part was cleaning under both refrigerators!
Thanks!