Your coupon for will be reflected when you check out!
✖
Your coupon for
✖
Hello!
You're visiting the PartSelect site in U.S.
Would you like to shop on the Canadian site?
Stay on this site
Go to Canadian site
✖
Model Number Locations
1Select Category Type
Select Category Type
2Select Product Type
Select Product Type
3Select {MODEL} Type
Select {MODEL} Type
Sample Model Number Tags
Model numbers can be made up of numbers (1005400, for example) or a combination of letters and numbers (LAT1000AAE). The model number will most likely appear on either a paper sticker or a metal plate. Your appliance's model number tag may look similar to the sample model number tags shown here (model number highlighted in yellow):
Model has been saved to My Models. If you're not signed in, your lists are available on this device and will expire within 30 days.
Model has been saved to My Models.
This lid lock, also known as a door lock, is a genuine OEM replacement part for your washing machine. The lid lock keeps your washer lid closed during the washing cycle. If this part is broken, your w...
This drain pump assembly is for washers. Drain pump assembly removes water from the washer during the drain portion of the cycle. The assembly may include multiple parts; refer to your parts diagram f...
This rod and spring assembly is designed to fit with washing machines and is made by the original manufacturer of your washer. It is a part of the washer suspension system that helps to stabilize and ...
This is a manufacturer-made suspension rod and spring assembly for your washing machine. This suspension rod is one of four suspension rods that make up the entirety of the inner suspension of your wa...
This drive belt is an authentic OEM part that is compatible with various models of washing machine. The drive belt is responsible for allowing the drum to rotate smoothly during the wash and spin cycl...
This is a clutch for your washing machine. The clutch is made of a white plastic material and is used within washing machines to engage and disengage the transmission during the wash and spin cycles, ...
This is a mode shifter or shift actuator for models of washing machine. Mode shifters are designed to change the function of the washing machine motor, between spinning cycles and agitation, and is us...
This auger is an authentic OEM replacement part specially designed for washing machines. It is a white, spiral-shaped agitator located in the center of the wash basket. During the wash cycle the auger...
This lid lock bezel, also known as a trim piece, is a genuine OEM part designed for washing machines. It is approximately 3.5 inches long. The bezel is a white, plastic frame that fits around the peri...
This is a speed sensor for a variety of washing machine models. Speed sensors are used to monitor the speed of the washer drum and communicate it to the electronic control board to slow or quicken it....
The agitator rotates back and forth to move the clothes inside the tub to clean the load.
$50.44
In Stock
Questions And Answers for GTW460ASJ6WW
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
34 questions answered by our experts.
Sort by:
< Prev
1
2
3
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Tonia
November 30, 2019
Why won't it spin??? why does it always beep when not in use?
For model number GTW460ASJ6WW
Hi Tonia, it may be a faulty door lock. If this part is broken, your washer may not run because it thinks the door is open. Based on the beeping it could also be a faulty control board.Thank you for your question and good luck with your repair!
Fabric softener container does not drain well. Use downy ultra he and usually fill to first line. At least every 5 loads I have to remove and clean container and holes to disperse are all gunked up.
For model number GTW460ASJ6WW
Hello Theresa, Thank you for the question. I suggest checking the water pressure to make sure it is flowing enough to rinse the softener from the cup. Hope this helps!
4 people found this helpful.
Was this helpful?
Thank you for voting!
Robert
March 25, 2022
When in delicate cycle washer bangs
When in normal wash cycle noisy slight grinding
My research says tub bearing...agree?
can't find it on your site
For model number GTW460ASJ6WW
Hi Robert,
Thank you for your question. If your washer shakes and moves, you will need to check the suspension rods, part numbers PS12343380 and PS12343381. If you are hearing a grinding noise when the washer is agitating, then the issue is likely tub bearing. The tub bearing would be part of the gearcase, part number PS12298171. Once you have determined the part you need, please feel free to call customer service. We are open 7 days a week and anyone will be happy to assist you. We look forward to hearing from you!
My washer will spin, but it won’t agitate. I’ve already put the door switch in and had it spin out but I can’t get it to agitate. Any suggestions?
For model number GTW460ASJ6WW
Hi Butch, thank you for the question. We have concluded that the issue is with the mode shifter, part number PS16554752, which may need to be replaced. The mode shifter is a component that causes the transmission to change between agitation and spinning modes. If the mode shifter is defective, the transmission may be stuck in the spin mode, resulting in the washer not agitating. Before replacing the mode shifter, make sure that the agitator is properly secured and not loose. We hope this helps, good luck with this repair!
Final spin, washer stops, light blinks & washer commences a refill. Control board?
For model number GTW460ASJ6WW
Hello John, Thank you for the question. Depending on what lights are blinking and how many blinks, this could indicate the Control Board is defective. We hope this helps!
Drain all the water out of the tub with a shop vac Remove rear drain hose and drained rest of water into a bucket Remove small rear panel (bottom left hand corner) where the drain hose connects Tipped washer up about 45 degrees to get underneath it - Supported it with a few paint cans Remove internal drain hose/clamps
... Read morefrom pump - w/ pliers Remove belt cover (gray plastic) with socket - 3 bolts Remove wire assembly plug from socket Remove old drain pump with socket - 3 bolts Install new drain pump - 3 bolts - plug wire assembly into socket Reinstall belt cover - 3 bolts Reinstall hose to drain pump (note panel will be inside washer) Feed drain hose panel through hole and reinstall - 1 nut Re attached drain hose to exterior drain plug You are done !
Very simple to repair. Be sure to drain the tub outside or into the sump pump then lay the washer on its side. The pump is right there on the bottom of the basket with 3 bolts. You will also need to remove the belt cover to get to the plug. So simple and saves you hundreds off repair man prices.
