Parts That Fix General Electric Washer GTW810SSJ1WS Leaking
Leaking is a commonly reported symptom for the GTW810SSJ1WS General Electric Washer, and we have put together a full guide
... Read more
on how to fix this. This advice is based on feedback from people who own this exact appliance. We have listed the most common parts for your GTW810SSJ1WS General Electric Washer that will fix Leaking.
We have included repair instructions, and helpful step-by-step video tutorials. If you are experiencing this issue, not to worry, DIYers just like you have fixed this, and shared their experience to help you!
Read less
Leaking is a commonly reported symptom for the GTW810SSJ1WS General Electric Washer, and we have put together a full guide on how to fix this.
This advice is based on feedback from people who own this exact appliance. We have listed the most common parts for your GTW810SSJ1WS General Electric Washer that will fix Leaking.
We have included repair instructions, and helpful step-by-step video tutorials. If you are experiencing this issue, not to worry, DIYers just like you have fixed this, and shared their experience to help you!
1 TUB SEAL
Fixes Symptom 32% of time
No Longer Available
PartSelect Number PS8757008
Manufacturer Part Number WH02X10362
Customer Repair Stories
Tub Seal Replacement - Direct Drive with Detergent/Fabric Softener Despensing
This procedure was completely different from any other Tub Seal I've done and in my opinion needs 2 people. The first thing to note is that this seal must be removed from the bottom of the outer tub. Also, the top of this machine does not hinge in back. The typical clips are in front, but the back has 2 screws that must be removed. Since
... Read more
the wiring was too involved to completely separate the top from the base, I had to improvise a stand to hold the top while the rest of the process was completed - keep slack on all remaining connected wires. The motor, clutch and bearing plate must be removed from the bottom in order to access the Tub Seal. Below are the steps I did to complete the process:
- Remove Control Panel Cover (rear)
- Disconnect as many wire harness plugs as possible from Control Board (Note positions for reassembly - pictures work well)
- Remove Pressure Switch
- Disconnect Detergent and Softener dispense hoses from Machine Top
- Rotate top 180 degrees (Flat-Spin) and position so no strain is on the still connected wires.
- Remove Tub Cover
- Remove Impeller (Agitator) from inside tub.
- Remove Tub Nut - Note Left handed Threads (I used 1/2" Drive Impact)
- Remove rear Cross Bar from cabinet (Cross Bar must be removed since tub will not fit through opening. Once removed it must be held in place or outer tub will fall)
- Remove Inner Tub - This tub is heavy and fluid-balanced. Mine required 2 people to wobble and pull for removal.
- Replace Cross bar to keep unit stable
- Lay machine on its side - use care not stretch or pull any wires.
- Remove motor, (Rotor and Stator)
- Remove Clutch and wires
- Loosen all wire ties (Use tiny screwdriver to release ties - Do Not remove the tie mount) securing wires to Bearing Plate and push wires to the outside edge of bearing Plate
- Remove all screws securing Bearing Plate to Outer Tub
- Use flat-head Screwdriver to gently pry Bearing Plate away from outer tub (Quite Heavy - Use Care)
- Tub Seal is now exposed on top of Bearing Plate and can now be removed and replaced (Be sure to clean all seal mating surfaces and lubricate with dish soap)
- Reverse this sequence in the exact order for re-assembly taking care to reconnect all wiring plugs and ground wires.
- During Re-assembly I used Blue Loctite on all bolts securing the Clutch, Stator, and Rotor as I found several very loose on my machine
- Remove Control Panel Cover (rear)
- Disconnect as many wire harness plugs as possible from Control Board (Note positions for reassembly - pictures work well)
- Remove Pressure Switch
- Disconnect Detergent and Softener dispense hoses from Machine Top
- Rotate top 180 degrees (Flat-Spin) and position so no strain is on the still connected wires.
- Remove Tub Cover
- Remove Impeller (Agitator) from inside tub.
- Remove Tub Nut - Note Left handed Threads (I used 1/2" Drive Impact)
- Remove rear Cross Bar from cabinet (Cross Bar must be removed since tub will not fit through opening. Once removed it must be held in place or outer tub will fall)
- Remove Inner Tub - This tub is heavy and fluid-balanced. Mine required 2 people to wobble and pull for removal.
- Replace Cross bar to keep unit stable
- Lay machine on its side - use care not stretch or pull any wires.
- Remove motor, (Rotor and Stator)
- Remove Clutch and wires
- Loosen all wire ties (Use tiny screwdriver to release ties - Do Not remove the tie mount) securing wires to Bearing Plate and push wires to the outside edge of bearing Plate
- Remove all screws securing Bearing Plate to Outer Tub
- Use flat-head Screwdriver to gently pry Bearing Plate away from outer tub (Quite Heavy - Use Care)
- Tub Seal is now exposed on top of Bearing Plate and can now be removed and replaced (Be sure to clean all seal mating surfaces and lubricate with dish soap)
- Reverse this sequence in the exact order for re-assembly taking care to reconnect all wiring plugs and ground wires.
- During Re-assembly I used Blue Loctite on all bolts securing the Clutch, Stator, and Rotor as I found several very loose on my machine
Read less
-
Greg from SPRING CITY, TN
-
Difficulty Level:Very Difficult
-
Total Repair Time:More than 2 hours
-
Tools:Nutdriver, Screw drivers, Socket set
15 of 18 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Fixes Symptom 32% of time
Introducing the GE Drain Hose, specifically designed for washing machines. This essential accessory safely transports used water from your washer directly to your house drain, establishing an efficient and reliable disposal system. Easy to install, it's recommended to shut off the water supply and disconnect the power from your washer prior to assembly to ensure your safety. For added protection, consider wearing work gloves during installment. Trust in the brand you know, GE, for a durable, high quality Drain Hose designed for long-term use.
$
45.95
In Stock
PartSelect Number PS8757195
Manufacturer Part Number WH41X10319
Fixes Symptom 20% of time
$
13.95
In Stock
PartSelect Number PS270985
Manufacturer Part Number WH1X2594
Fixes Symptom 15% of time
Introducing the GE 5 Solenoid Water Valve - an essential component for your washer. This water inlet valve expertly controls the flow of water into your washer, ensuring consistent and accurate water usage during every cycle. Please remember to disconnect your appliance from power and turn off your water supply before beginning your installation. It's advisable to don work gloves for this task, to shield your hands during the process. This part is specially manufactured by GE, guaranteeing optimal performance and the highest quality.
$
110.83
In Stock
PartSelect Number PS8746230
Manufacturer Part Number WH13X10058
Customer Repair Stories
Constant Drip into Washer Tub
Secured power and supply lines. Took off rear panel. Labeled all 5 electrical inputs to water valve. Could not get water valve out. Found the 5 hoses that were clamped to the 5 valve inputs by going head first into the washer. Did not order the clamps!!!! Even if we had, we couldn't figure out how to access them. Called appliance guys who
... Read more
installed valve and clamps.
Read less
-
Margaret from NORFOLK, VA
-
Difficulty Level:Very Difficult
-
Total Repair Time:More than 2 hours
-
Tools:Screw drivers, Socket set, Wrench (Adjustable)
4 of 4 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!