JCGBS66EEK1ES General Electric Range - Instructions

the flame spreader through the years, developed a hole above the glow coil causing the above trapped gas between the oven pan and spreader to ignite. by replacing the flame spreader the problem is gone and is now working properly. thank you, parts select for being there when i needed the part and also being reasonably priced. mike marino

Removed old gasket and pried out clips with screwdriver. Installed new gasket.

Remove griddle insert grate

I had to call for a appointment for repair with GE Appliance because I thought then it . .was something electrical. The technician came out & checked everything out, turned out it was not electrical, The technician went out to his truck got a light bulb from his truck, put it in & it worked. It cost me $121.00 for trip charge from GE appliance for a light bulb that worked, your light bulbs were defective twice. Very disappointed with your products, cost me alot of money for a good light bulb thru GE appliance

Unplugged the appliance for safety. Removed two 1/4" screws that held the assembly in place. Carefully removed the wire guard that retains the glass shield. Unscrewed old light bulb and replaced with new part. Reversed the steps after cleaning glass cover.

Put in a new foot / bumper. That's it.

put the new griddle in its place

New burner cap replaced old; just placed over burner; no tools required.

One suggestion: burner cap should have been shipped with thicker bubble protection (easy to do). It was minimally wrapped and placed in a thin, bubble envelope, risking damage in shipping process. Luckily, the burner arrived in tact and usable.

Removed bottom shelf from inside oven, turned it obj and replaced the oven deflector with only a screwdriver

I cut the box open with a utility knife and removed the grill. I then opened the oven door and rearranged the two existing racks so that the third one would go in so they all have the same distance between each of them. I slid the new rack into position. It didn't go in smoothly though as I had to push it in and out several times so that it would line up perfectly. Finally in went in all the way. Then I closed the oven door and went and sat down to think about the wonderful job I just did.

1) Turn off power at circuit breaker panel
2) Slide out Range from wall
3) Unplug Range
4) Remove back panel and unplug electrical connections to socket
5) From front of oven, remove glass cover over old oven light bulb and remove flange that holds socket and bulb
6) Remove old socket from mounting flange and discard.
7) Place new socket into mounting flange
8) Screw mounting flange and new socket into the oven from front. Reattach electrical connections from back.
9) Screw in new light bulb from front
10) Replace existing glass cover over new light bulb and snap wire holder in place
11) Replace back panel
11) Plug in range
12) Slide range back to original position
13) Turn on power
Works like a charm! Thanks for having the parts after 30 years!

Turned off gas, then lifted up the burner cover and removed the old valve using a screw driver to loosen the clamp. I also had to remove the face plate using a socket set (4 screws). I didn't align the valve using the existing valves as a guide and also didn't get the clamp tight enough. So I re-aligned the valve to match the other valves and also tighten the clamp enough as best I could to prevent gas from leaking.

First I checked that the wire and sparker was working by switching the wires on top of the range. I did this by pulling out the sparker switching it from the back working burner on the same side. The same burner would not light so I knew it was not the sparker.

Then watch a bunch of videos and found this gal to be the most helpful on how to take apart my exact stove.
Go here: https://www.youtube.com/watch?v=WRGfuhUzEaY

I did not take everything apart like she did. I ordered the spark module and just replaced it following her method to take off the back, switch the wires to the new module, then put everything back together again.

All burners have been working perfectly since the fix.

I removed the original gasket clips with pliers. I installed the new gasket by aligning the clips with the holes around the door and pressed into place. Easy fix!

Just lifted old burner off with my fingers and replaced with the new one. What needs to be focused on here is the fact that Part Select has such a complete line of parts rather than the difficulty in the install.