JE1160B General Electric Microwave - Overview
Sections of the JE1160B
[Viewing 1 of 1]
Keep searches simple, eg. "belt" or "pump".
Cooking Tray
PartSelect #: PS248296
Manufacturer #: WB39X82
This tray rotates in your microwave ensuring more even temperatures.
$66.95
Special Order
Microwave Light Bulb And Socket
PartSelect #: PS247776
Manufacturer #: WB36X951
This light bulb is sold with the socket. The bulb is 120V and 25W.
No Longer Available
Magnetron
PartSelect #: PS953838
Manufacturer #: WB27X10682
This part is used to generate microwave energy/heat.
No Longer Available
Turntable Guide with Rollers
PartSelect #: PS224055
Manufacturer #: WB02X10806
This microwave turntable guide is located under the glass turntable. It is made of plastic, and comes with rollers.
No Longer Available
Switch
PartSelect #: PS237415
Manufacturer #: WB24X823
This is sold individually. Your appliance would need 2 of these.
$81.13
In Stock
Questions And Answers for JE1160B
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Symptoms of the JE1160B
[Viewing 3 of 3]Won’t turn on
Fixed by
these parts
these parts
Show All
No heat
Fixed by
these parts
these parts
Show All
Tray won’t turn
Fixed by
these parts
these parts
Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Original lamp burned out.
After looking up on the computer a schematic of the unit, all that was needed was removing four screws to remove the top and side cover which was one piece.
Next was removal of electrical connection to burned out lamp, then removing burned out lamp and installing the new lamp and reconnecting electrical connection.
Job was co ... Read more mplete after reinstalling the cover.
Microwave now working with new lamp lighting when in use.
Next was removal of electrical connection to burned out lamp, then removing burned out lamp and installing the new lamp and reconnecting electrical connection.
Job was co ... Read more mplete after reinstalling the cover.
Microwave now working with new lamp lighting when in use.
Read less
Parts Used:
-
Rudy from Huntington, IN
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
73 of 89 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Microwave oven was completely dead.
Continuity checks showed the flame sensor was open. Schematic notes it opens at 217 degrees and closes at 30 degrees. Removed sensor and placed in freezer for twenty minutes. Tested sensor and it was now closed, reinstalled and microwave worked normally. Ordered new sensor in case the original is operating at too low a temperature.
Parts Used:
-
CHARLES from LAKE ARIEL, PA
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Screw drivers
29 of 39 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Both Intermittent- and No-Heating
First, I read the PartsSelect DIY report by Linda, Warsaw, IN. With confidence, I purchased the magnetron. Upon receipt, I took the built-in microwave out of the cabinet, set the unit on the kitchen floor, and was stopped cold by the Safety Torx nuts on the reverse of the unit. Borrowing the right wrench allowed the 20 minute start-to-
... Read more
finish part changeout and reinstallation of the unit in the cabinet to proceed. The old magnetron was the defective part. Discovery of the 10-year Parts-Only warranty on the less than 10-year old unit was insufficinet to guide me to take the unit in for their Labor bill to repair. New part in hand, it just was that easy - and assumed to be no less expensive.
Read less
Parts Used:
-
Richard from Merritt Island, FL
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
18 of 24 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!