JGBP26WEH6WW General Electric Range - Instructions

A G.E. tech came out and quoted $500 to replace the circuit board. I unbolted the board myself and used the camera in my phone to take a picture of the wiring. Then I came to PartSelect.com and using their diagrams found the replacement board for $75. It came in the mail a few days later. I used to picture in my phone to reconnect all the wires, bolted everything back up and baked some cookies. Thanks PartSelect for making my repair job simple and inexpensive.

My husband and I simply took the burner units out of the packing, took the old ones off, put the new ones in. The new units needed to be leveled, but the leveling nuts included fit perfectly, and the entire repair took less than 15 minutes.

I turned off the gas flow to the appliance, removed the old oriface spuds with the adjustable wrench, inserted the new oriface spuds and tightened them with the adjustable wrench. The double burner assembly just dropped on. They fit perfectly. I did not have to use the leveling nuts that were included with the burners. The old levelers were still in place and set perfectly for the new burners. Very easy repair, and the range works like a new one.

Removed the two screws put the heat shield off the old one onto the new one put new bottom in and tightened two screws. Done #38. 69 Cost of part with shipping cost included.

I was very pleased with how quickly the new oven rack arrived and it was a perfect fit. Thanks.

The toughest part of the repair was the preparation to remove the old burners. As a result of the burning there was a carbon residue on the burners, on the gas outlet feed to the burners. This took some scrubbing and removing the carbon residue. Bits had burned onto the outlet and had to be scrapped off. Once all cleaned, replacing the burners was easy just had to place the balancing nuts in place and put on the burners. One problem arose the hood of the stove did not go back in place after replacing the burners so I then removed the balancing nuts put back on the burners stove top hood fit back in place and burners operated properly. This part of the repair took five minutes.

I ordered a new display from the internet. I removed the panel where the display is housed, unscrewed the entire display assembly and unplugged all wires connecting it. (I made a drawing and noted colors of wires) I removed adhesive face of display and replaced it on the new display. I then screwed in the display and reconnected the wires as per my notes. I reassembled the panel and applied power and it worked like new.

Very easy! Open the top of the stove, remove the old double burner and place the new one! Anyone can do it! It's that easy... :)

Thanksgiving was coming and I needed extra oven space. So I ordered an additional rack. Installation ... just put it in the oven. My part came the day after I ordered it.

removed two screws and took out bottom tray and put the new one in and replaced the screws.DId it my self.

I had to call for a appointment for repair with GE Appliance because I thought then it . .was something electrical. The technician came out & checked everything out, turned out it was not electrical, The technician went out to his truck got a light bulb from his truck, put it in & it worked. It cost me $121.00 for trip charge from GE appliance for a light bulb that worked, your light bulbs were defective twice. Very disappointed with your products, cost me alot of money for a good light bulb thru GE appliance

Unplugged the appliance for safety. Removed two 1/4" screws that held the assembly in place. Carefully removed the wire guard that retains the glass shield. Unscrewed old light bulb and replaced with new part. Reversed the steps after cleaning glass cover.

First I removed the back panel and then removed the four screws that hold the display board in place.I then disconnected the wires.
I installed the new board and connected the wires.
I put the back panel on.
I installed a serge protector and pluged in the range. Job completed and it worked.

First I tested oven sensor which checked o k. I then made a diagram of the electrical wireing to the oven control. I disconnected wireing and removed the control then with sharp knife I removed touch control pad. I placed th touch pad on the new panel and installed panel and connected wiring. Pluged into wall rec and test oven which checked o k .

took drawer out removed broken guide. It had 1 screw removed it put the new guide in place put screw back in. Put drawer back in stove, It works fine.