JK25*R3 General Electric Range - Overview
Sections of the JK25*R3
[Viewing 1 of 1]Keep searches simple, eg. "belt" or "pump".

Oven Bake Element 240v
PartSelect #: PS249424
Manufacturer #: WB44X200
This is a 240 volt bake element for your oven or range. The kit comes with two installation screws and the element. The element functions by supplying heat from the bottom of the oven to bake or cook ...
$44.95
In Stock

Oven Bake Element
PartSelect #: PS249483
Manufacturer #: WB44X5099
This closed hinged-style bake element has screw in terminals.
$42.95
In Stock

Range Broil Element
PartSelect #: PS249411
Manufacturer #: WB44X173
The broil element is located at the top of the oven and gives off heat in order to bake evenly. If you notice that the element is not heating up or is not cooking evenly it could be because it is brok...
$41.95
In Stock

Thermostat
PartSelect #: PS235956
Manufacturer #: WB21X5209
The length of this thermostat's capillary is 62 inches.
No Longer Available
Questions And Answers for JK25*R3
Be the first to ask our experts a question about this model!
✖
Ask a Question
Ask our experts a question on this model and we'll respond as soon as we can.
Sorry, we couldn't find a match for "".
Here's a guide for finding your model number.
Something went wrong. Please try again later.
Your Question Has Been Submitted!
Our experts will send you an email as soon as your question has been answered.
Common Symptoms of the JK25*R3
[Viewing 7 of 7]Little to no heat when baking
Fixed by
these parts
these parts



Show All
Element will not heat
Fixed by
these parts
these parts



Show All
Little to no heat when broiling
Fixed by
these parts
these parts


Show All
Oven not heating evenly
Fixed by
these parts
these parts



Show All
Will Not Start
Fixed by
these parts
these parts



Show All
Oven is too hot
Fixed by
these parts
these parts


Show All
Touchpad does not respond
Fixed by
these parts
these parts

Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Replacment of the bake unit
The hardest part was removing the old nuthead screws off the old bake burner. Once those were off installing the new bake element was simple. One screw in each wire terminal, two hex head screws to hold the unit in place. Works like a charm!
Parts Used:
-
Beth from Matthews, NC
-
Difficulty Level:Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Nutdriver, Socket set
611 of 626 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
oven lower burner burned out
Very easy, remove two screws, pull burner unit out slightly, then remove the two screws attaching the wires, one to each side, remove old unit and replace with new unit and replace screws.
Works fine perfect replacement.
Works fine perfect replacement.
Parts Used:
-
james from franklin, TN
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Nutdriver, Screw drivers
509 of 592 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Bake element was on its last legs, starting to crack but still functional.
Removed the racks, unscrewed the back plate which holds the element, unscrewed the leads from the element, removed the old part.
Reversed the process to install the new element.
Turned the oven on for a few minutes to burn any contaminates off the new element, replaced the racks.
And that was it; quite ea ... Read more sy.
Reversed the process to install the new element.
Turned the oven on for a few minutes to burn any contaminates off the new element, replaced the racks.
And that was it; quite ea ... Read more sy.
Read less
Parts Used:
-
Lawrence from San Jose, CA
-
Difficulty Level:Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Nutdriver, Screw drivers
223 of 373 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!