Your coupon for will be reflected when you check out!
✖
Your coupon for
✖
Hello!
You're visiting the PartSelect site in U.S.
Would you like to shop on the Canadian site?
Stay on this site
Go to Canadian site
✖
Model Number Locations
1Select Category Type
Select Category Type
2Select Product Type
Select Product Type
3Select {MODEL} Type
Select {MODEL} Type
Sample Model Number Tags
Model numbers can be made up of numbers (1005400, for example) or a combination of letters and numbers (LAT1000AAE). The model number will most likely appear on either a paper sticker or a metal plate. Your appliance's model number tag may look similar to the sample model number tags shown here (model number highlighted in yellow):
Model has been saved to My Models. If you're not signed in, your lists are available on this device and will expire within 30 days.
Model has been saved to My Models.
This OEM gray Dishwasher Lower Dishrack Wheel Assembly is a plastic kit that allows the rack to slide in and out of the dishwasher easily. If it breaks or becomes damaged. sliding will feel difficult....
$33.57
In Stock
Order within the next 9 hrs and your part ships today!
This part is a door balance link kit, also sometimes known as door cable or door spring cable kit, that helps support the door as it opens and closes by connecting to the dishwasher door hinges. The k...
$27.95
In Stock
Order within the next 9 hrs and your part ships today!
This OEM Dishwasher Upper Rack Adjuster is a grayish-black, plastic part which will require a screwdriver to install. It fits onto the dishwasher rack and connects it to the track allowing it to slid...
$32.54
In Stock
Order within the next 9 hrs and your part ships today!
The mounting bracket is sold individually, without screws. This part secures the upper side of the dishwasher to the underside of the counter or cabinet to prevent the dishwasher from moving, shaking,...
$14.65
In Stock
Order within the next 9 hrs and your part ships today!
Also known as rack adjuster. Sold individually.
This is an original part from KitchenAid, Kenmore, Whirlpool, Jenn-Air, and Maytag for use with Dishwashers. The dishrack adjuster arm positioner clip...
$45.95
In Stock
Order within the next 9 hrs and your part ships today!
This is the dishrack slide track for the left side of various dishwashers. This track allows your upper dishrack to be supported and slide in and out of the dishwasher to place or remove dishes from t...
$58.62
In Stock
Order within the next 9 hrs and your part ships today!
Sold individually.
This dishrack adjuster is for dishwashers.
Dishrack adjuster lets you change the height of the dishwasher's upper rack.
Wear work gloves to protect your hands when installing this part.
$33.95
In Stock
Order within the next 9 hrs and your part ships today!
This dish rack slide rail is a genuine OEM replacement part that is compatible with various models of dishwasher. It is designed to fit on the right side of the dishwasher. The slide rail or track sup...
$56.95
In Stock
Order within the next 9 hrs and your part ships today!
The tine row on your dishwasher rack divides the rack into columns to keep your kitchen items in place during the washing cycle. If you notice that one or more of the tines on your current tine row is...
$49.33
In Stock
Order within the next 9 hrs and your part ships today!
This water inlet valve should be located behind the lower kick plate panel in either the right or left corner. The attaching solenoids on the valve open and close according to the desired amount of water needed.
$52.45
In Stock
Order within the next 9 hrs and your part ships today!
Questions And Answers for KDTE104ESS4
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
6 questions answered by our experts.
Sort by:
< Prev
1
2
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Rick
May 30, 2022
What are the physical dimensions for this model?? i am getting new cabinets and i need to make sure the dishwasher will fit.
For model number KDTE104ESS4
Hello Rick, Thank you for your inquiry. We show the dimensions of this model as approximately 34 1/2 inches high, 23 7/8 inches wide, and 24 1/2 inches deep without the handle, and the depth with the door open 90 degrees as 49 1/2 inches. We hope this helps and if you need a part in the future and need help placing an order, customer service is open 7 days a week. Please feel free to give us a call. We look forward to hearing from you!
Was this helpful?
Thank you for voting!
Chris
July 31, 2023
The top rack assy broke off I need the part to reconnect the rack to the slides
For model number KDTE104ESS4
Hi Chris, thank you for asking. You may need to replace the upper rack adjuster, part number PS11756150, to fix the issue. It fits onto a dishwasher rack and connects it to the track, allowing it to slide in and out. Glad to be of assistance!
When washer is running top sprayer does not turn move
For model number KDTE104ESS4
Hi Gary, thank you for the question. Based on our understanding of the issue, we would suggest checking the water supply tube for any clogging. If that is not the issue, you may need to check the upper spray arm, part number PS11752935, to fix the issue. We hope this sorts out your problem!
I want to order a new control board for dishwasher but I can not get door off to see control board. Help
Thank You
Last week I replaced inlet valve
Thank You
For model number KDTE104ESS4
Hi Robert, thank you for the question. The control board for your model is part number PS12704672. We have found the instructions to access the control board. These may not be of the same model but will help you in accessing it. You may need to un-thread all the screws holding the inner and outer door panels together. Separate the panels and release the door latch. Disconnect the wire connector and detach the retainer to fully remove the outer door panel. Un-thread the screws securing the control board mounting bracket to the frame and move the bracket out of the way to reach in to the control board. We hope that helps!
My dishwasher doesn’t work properly, doesn’t dry the dishes, it’s doesn’t clean well, the heat dry mode doesn’t work, the panel it’s constantly blinking …….. in general, I think the control panel it’s not working as well as it was.
What should I do?
For model number KDTE104ESS4
Hello Martha, thank you for your inquiry. Your issue may be the Filter PS11759673 or the Heating Element PS9494999. If the door is opened during a running cycle to add an item, all cycle and options selected lights, will flash to indicate that the cycle is suspended. Firmly close the door until it latches. We hope this helps.
Pulled dishwasher from under counter, attached link to spring, hooked spring back into frame/chassis, threaded link through pulleys, attached other end of link onto door, reinstalled dishwasher under counter. All's well. Note-I purchased an extra link anticipating that the other one will fail. They're cheap enough.
1. Open the dishwasher and remove the two plastic grommets about halfway down on either side of the opening. Then remove the two screws under the grommets.
2. Remove the kick plate under the door. May have to lower unit by turning the feet using the adjustable wrench.
3. Make sure you have enough slack in the water i
... Read morenput line and electrical wiring that you can pull the dishwasher out about 12 inches or more.
4. There is a spring and nylon rope link on both sides of the unit. Probably just one link is broken, but the replacement comes with two, so you can replace both or save one as a spare. Look at the good side and it should be pretty self explanatory how it attaches. I found it easiest to first thread the link around the lower pulley, then attach the link to the spring, then spring to the rear support, then the link to the door.
This was the second time I had this problem so I knew the symptoms and remedy. The tools needed were two nut drivers a ¼” and 5/16” along with a flat pry bar and Phillips screw driver. I started by removing the lower front panel by removing the two ¼” screws on either side. The lower panel will lift up and then can be removed by pullin
... Read moreg on the bottom. There is a flat sheet metal piece behind the front panel with insulation that can be removed very easily along with the front panel. When the front panel is removed it exposes the front legs that may need to be dropped to let you lift the dishwasher over the tile (if you have ceramic tiles). The next step would be to remove any ties to the counter top if it is attached. Mine were attached by the two straps on either side with Phillips screws. After the top is free, lower the front legs by lifting the dishwasher with the flat pry bar and threading the legs up into their holders. With the legs lifted the dishwasher can be pulled out to expose the tension springs located along the sides at the very bottom. Chances are the ropes are broken off the plastic holders that fit over the door hooks. Remove the plastic guides by removing the 5/16” nut from the middle of the lower roller. Remember to note which hole the screw is coming from this also sets the tension for how fast or slowly the door drops. Placing the nut closer to the front will drop the door slowly and toward the back will drop the door more quickly. I placed mine in the middle hole. When the plastic guides are removed attach the nylon pope to the spring and attach to the back of the dishwasher. There is a hole located on a flat piece of sheet metal the spring will attach to at the back of the dishwasher (if it is broken). Check the other side if it is still in tact. With the spring in place weave the rope around the plastic guides then pull the springs to help get the plastic end over the door hook located at the bottom of the door. Repeat this operation for the other side (kit has a both sides covered) and reinstall dishwasher in cabinet. Steps 1) Remove front panel (1/4” nut) 2) Release Dishwasher from Cabinet 3) Lower front legs 4) Pull Dishwasher out from under Cabinet 5) Remove Rope Guide (5/16” nut) 6) Install new Rope Guide (Supplied in Kit) 7) Attach new rope to Spring and attach spring to dishwasher 8) Weave rope through rope guide 9) With door closed pull spring to relieve tension so rope can be attached to door 10) Repeat for other side (Kit has both sides)
