Your coupon for will be reflected when you check out!
✖
Your coupon for
✖
Hello!
You're visiting the PartSelect site in U.S.
Would you like to shop on the Canadian site?
Stay on this site
Go to Canadian site
✖
Model Number Locations
1Select Category Type
Select Category Type
2Select Product Type
Select Product Type
3Select {MODEL} Type
Select {MODEL} Type
Sample Model Number Tags
Model numbers can be made up of numbers (1005400, for example) or a combination of letters and numbers (LAT1000AAE). The model number will most likely appear on either a paper sticker or a metal plate. Your appliance's model number tag may look similar to the sample model number tags shown here (model number highlighted in yellow):
Model has been saved to My Models. If you're not signed in, your lists are available on this device and will expire within 30 days.
Model has been saved to My Models.
The charcoal filter, used in microwaves, removes food odors from the air. If your filter is damaged or you notice strong odors coming from your microwave, it is best to replace it. This part is metall...
$20.95
In Stock
Order within the next 57 mins and your part ships today!
This surface light bulb is used in ranges and microwaves. It has a high voltage of 12 and 10 watts. This bulb illuminates and directs light at the bottom of the microwave or the inside of it. It also ...
$20.97
In Stock
Order within the next 57 mins and your part ships today!
This door interlock switch is a genuine replacement part designed for use in microwaves. It serves a critical safety function by preventing the microwave from operating when the door is open. Because ...
$30.95
In Stock
Order within the next 57 mins and your part ships today!
This part is a replacement glass cooking tray for your microwave. The cooking tray rotates when the microwave is running, and helps your food cook evenly. As it is made of glass, these glass cooking t...
$53.85
In Stock
Order within the next 57 mins and your part ships today!
If your microwave is not turning on it could be due to your fuse needing to be replaced. This part protects the microwave by shutting it off if there is an electrical surge. This fuse is just over an ...
$32.95
In Stock
Order within the next 57 mins and your part ships today!
This damper is an authentic OEM replacement assembly used in microwave/range hood combos. It includes the damper door and frame. It is designed to direct the flow of air through the vent duct, and the...
$54.83
In Stock
Order within the next 57 mins and your part ships today!
Also known as the coupler. This driver is located directly under the glass turntable, and over the motor. This part helps the glass turntable to rotate.
$26.95
In Stock
Order within the next 57 mins and your part ships today!
Ask our experts a question about this model and we'll get back to you as soon as possible!
4 questions answered by our experts.
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Tom
January 10, 2020
The lights do not work. We have replaced the bulbs, but still not turning on?
For model number KHMS2056SSS4
Hello Tom,
Thank you for your question. Our sources suggest replacing the light socket for your model under part PS1961309 to fix the light issues. We hope this helps!
It was suggested I replace the light sockets on this unit. Since replacing the bulbs did not work. How easy is it to replace the sockets and are there instructions on how to do it somewhere?
For model number KHMS2056SSS4
Hi Tom. It is not very difficult. To install the socket you will have to remove it from all power and if it is attached to a wall remove it and put it onto a stable surface. Then you will have to remove the back panel by removing all the back panel screws. Lower the back panel making sure it does not fall out. Disconnect the wire harness that goes to the light bulbs. To unplug the wire all you have to do is squeeze each side to release the locks and disconnect it. Set the back panel aside. There will be two lock sockets on each side of the back panel. Remove the wire harness from the socket. There may be a tab you will have to push in and a screw you will have to remove. Pull the light socket out of the housing carefully. Unscrew the bulb so you can put it into the new socket. Put the bulb into the new socket then feed back into the housing. Put the screw that holds it on in and bend the tab back over to secure the socket. Then reconnect the wire harness. Repeat this process for the other socket. Then you can put the panel back onto the microwave. Reconnect the wire harness for the light sockets. Lift the panel up and put the screws back in. Thank you for your question and good luck with your repair!
I want to replace the filters that are directly accessible behind the lights. They clip into a square frame. Which filter should I use.
Thank you
For model number KHMS2056SSS4
Hi Janet, thank you for your inquiry. According to our research, there are two filters at the above-mentioned location. The charcoal filter, part number PS1957304, and the grease filter, part number PS1957303. We hope this information helps!
What size screw head or type of tool do you need to remove the and replace the the light bulb?
For model number KHMS2056SSS4
Hi Scott, thank you for your question! To remove the halogen light bulb, part number PS886465, you may pull the bulb out. Once the old light is removed, you can push in the new light. We hope this information is useful!
There was no "fixing" per say but we still could not use the microwave without the plate. This has to be one of the biggest plates for a microwave. We ordered this through your company and we had it three days later. THREE DAYS! We had expected anywhere from 1-2 weeks. My husband was so impressed he bookmarked your site for future re
... Read moreference. Thank you for being so efficient and prompt. The glass turntable fit like a glove! Sincerely, Mark and Lia Hammond
Remove the filters and use a Torx driver to remove two screws holding the motor. The wires on on the motor are held in place by a plastic clamp that must be pried open on one side. That's all it takes to replace the drive motor. Everything else that makes the turntable spin lifts off from inside the microwave.
By pulling the filter screens units down and out with a pair of pliers I had access to the surface lights. Pulled the lights out of their sockets and replaced the bulbs. Real easy. Since the filter units were out, replaced the filters and reinstalled the filter units. The whole operation took less than 15 minutes.
