Parts That Fix KitchenAid Dishwasher KUDC10FXSS5 Leaking

This fill hose is a genuine OEM replacement part for your dishwasher. The hose is made of black plastic, and is accordion-style, for ease of movement within your dishwasher. To replace the fill hose, you will need a 1/4 inch nut driver, Channellock pliers, and a Phillips screwdriver. Replacing this part will require some disassembly, such as removing the water inlet valve from the fill hose, and the clamps which secure the hose in place. Reuse your existing clamps when securing your new fill hose in place.

This part is used to drain water from your dishwasher.

The hose clamp is used to hold the water hose in place which will prevent the hose from leaking water. Sometimes the clamp may lose its ability to latch on, causing a leaking washer. For the installation, you will need a flat head screw driver to replace the clamp and a drill to access the screws to remove the front of the washer. Be careful if you do not have specific clamp pliers as the clamp could fly off. Once the front of the washer has been removed, take a quick look for water damage or any obvious signs of where the leak is coming from. If it is not obvious, run water to test.

This is the replacement impeller kit for your dishwasher. This impeller kit comes with 4 pieces, including the impeller and seals which you will need for the repair. The impeller and seal kit is mounted on the dishwasher motor. If your dishwasher is not cleaning dishes properly, it may be an indication that your impeller has gone bad, and you are not getting proper water pressure. If the seals have gone bad, your dishwasher may start to leak. If you are having either of these problems, you may need to replace the impeller kit. Be sure to disconnect the water and power source from the dishwasher before you begin this repair. This is an OEM part sourced directly from the manufacturer.

This part is also known as a float switch. This float switch, when activated, stops the flow of water into the dishwasher.

Also known as a washer.

This part forces the water from the pump to the sump area for discharge.

The rubber washer is a part which is specific to dishwashers and should not be substituted by a similar part. It works with the heating element to seal the receptacle opening where the heating element is attached. The rubber washer is used to prevent water leaking from your dishwasher during its cycle. Before making any repairs to your dishwasher make sure that you disconnect the power by finding the breaker for the dishwasher, and turning it off. The tools you will need to complete this repair include an adjustable wrench, and a 1/4 inch nut driver. This specific rubber washer is sold individually.

The circulation pump and motor is located near the bottom of the dishwasher. The part functions by spinning the impeller of the circulation pump, which is used to move the water through the spray arms during the wash cycle. Before you begin this repair, it is recommended that you pull your dishwasher out of the cabinet, so you can tip the dishwasher to one side and gain better access to the circulation pump and motor. Be sure to disconnect the power source and the water source to the dishwasher before you begin this repair. To complete this repair you will need a 1/4 inch nut driver and a 3/8 inch nut driver.

This drain pump is used in dishwashers to remove water from the dishwasher tub. If the impeller in the dishwasher is damaged or the motor has been shorted out and will not drain, it is possible the body is cracked, causing leakage. To prevent this from happening, replace the drain pump. The tools needed for this installation are: Phillips screwdriver, 5/16 inch nut driver, 5/8 inch wrench, and a flathead screwdriver. Remember to unplug your dishwasher from the power source before beginning this installation project. Refer to the manual provided by the manufacturer for further installation instructions.

Water inlet gasket WP8531323 is a water inlet gasket for dishwashers. It ensures a watertight seal at the point where water enters the tub, preventing leaks and maintaining efficient water flow during the wash cycle.

Sold individually.

Measures level of soil in the water.

Discover the practicality and efficiency of the Whirlpool Dishwasher Housing. This genuine OEM piece is specifically designed for safety float functions, holding and supporting the float stem and float switch ensuring your appliance performs at its optimum level. It is crafted compatible with various Whirlpool, KitchenAid, Maytag, Jenn-Air, Amana, Inglis, and Magic Chef dishwasher models. Despite potential size and shape variations across parts, rest assured this housing fits seamlessly with your specific appliance model contributing to a sturdy, reliable setup. Be sure to unplug your dishwasher and shut off your water supply prior to installation, and protecting your hands with work gloves is recommended. Entrust your appliance to the superior quality and durability of Whirlpool parts.

This is a flexible drain hose that is 12 feet long.

Also known as a wash arm seal.

This part has a large port for the soil sensor and thermistor.

Also known as a water supply tube which is used for your middle spray arm.

This part is a door balance link kit, also sometimes known as door cable or door spring cable kit, that helps support the door as it opens and closes by connecting to the dishwasher door hinges. The kit includes two door balance links and two door balance mounts with wheels, which will replace both the left and right sides. The only tool needed is a 5/16 nut driver. Before removing the existing kit, take note of how the door balance link kit is assembled for a smooth replacement process. It is recommended to check the door springs in case they need to be replaced as well.

Shield

This seal is located between the spray arm and the water feed tube.

Introducing the Whirlpool Dishwasher Door Brace, a genuine Whirlpool part designed to notably enhance the performance of your dishwasher. This durable brace, specially engineered to replace the flat panel vapor barrier, has been crafted with a rod to keep the hinges straight, ensuring better alignment and longevity of your dishwasher door. This component assists in reinforcing the rear of your dishwasher tub, adding to the overall structural integrity. Designed for easy installation, you'll want to disconnect power and shut off the water supply before beginning to ensure a safe process. It's recommended to verify the correct part for your enterprise model before acquisition. Turn to Whirlpool's trusted reliability for this exceptional dishwasher door brace to keep your unit running smoothly.

Introducing the Whirlpool Dishwasher Detergent Dispenser, an authentic OEM part designed to perfectly fit your appliance. This detergent dispenser is crafted to operate with various Whirlpool, KitchenAid, Maytag, Jenn-Air, Amana, Inglis, and Magic Chef dishwasher models. Acting as a reservoir, it effectively holds your dishwasher detergent and rinse agent in secure compartments. Wait for the dishwasher to be unplugged and water supply shut off before setting up this component. As an added safety measure, it's recommended to wear work gloves during the installation to protect your hands. With this dispenser, you'll be enhancing your dishwasher's performance, ensuring cleanliness for every cycle.

This part moves water up from the sump collection area and up through the spray arms.

This OEM gray Dishwasher Lower Dishrack Wheel Assembly is a plastic kit that allows the rack to slide in and out of the dishwasher easily. If it breaks or becomes damaged. sliding will feel difficult. This can happen due to normal wear and tear, and the part should be replaced if this occurs. Check your model number and user manual to make sure this part is correct. It attaches directly to the dishrack. To repair, open the dishwasher door and pull out the lower dishrack. Next, push the tab from both sides and it should pop out. To install the new wheel assembly, place it on the rack and make sure the caps overlap the wire from the inside before you clip it in place by pushing the wheel. It measures roughly 3x6 inches.

May differ in appearance, but functions same as original. This valve allows the water to flow in the drain direction only and prevents the dirty water from coming back into the tub.

The heating element is not designed to heat the water that enters it, but is designed to maintain the heat of the water that enters the dishwasher. It is located on the bottom of the dishwasher.

The mounting bracket is sold individually, without screws. This part secures the upper side of the dishwasher to the underside of the counter or cabinet to prevent the dishwasher from moving, shaking, or tilting forward. The bracket is made entirely of metal. It is recommended to check all brackets, if applicable, because they often wear at the same rate and both may need to be replaced. This is an OEM part that is sourced from the authentic manufacturer. Tools needed are a pair of needle nose pliers and a screwdriver.

Supplies water from the main water feed tube to the middle manifold water tube.

This is a chopper assembly or drain food chopper, and it is designed for your dishwasher. The chopper chops up/minces the food particles in your dishwasher to prevent them from clogging the pump. You may need to replace this part if your dishes are not being cleaned properly, your appliance is particularly noisy, or you are noticing draining problems. The tools you will need to make this repair include a number 20 and a number 15 torque screwdriver, a small flat blade screwdriver, and a pair of needle nose pliers.

NOTE: This part has been redesigned, it may appear different but will still function the same as the original.

The plastic button covers the sharp ends of screws along the edge of the dishwasher tub. Sold individually.

This part is a replacement screw for your dishwasher. It is made of metal and is approximately ¾ inch long. It is a hex-head screw and is sold individually. It is used to hold the dispenser bracket in place. This part is a genuine OEM part sourced directly from the manufacturer.

The spray arm in your dishwasher spins and sprays the water that is used to clean your dishes. If the spray arm is damaged, your dishwasher will not clean properly, and you will need to replace it. Many of our customers have rated this repair as easy, and to complete the repair you will simply need to unscrew the old arm, and replace it with a new one. Make sure the jets are facing upward when you secure the new arm. This part is made of gray plastic and is approximately 18 inches wide.