Parts That Fix KitchenAid Dishwasher KUDC10FXSS5 Will Not Start
NOTE: This part has been redesigned, it may appear different but will still function the same as the original.
The circulation pump and motor is located near the bottom of the dishwasher. The part functions by spinning the impeller of the circulation pump, which is used to move the water through the spray arms during the wash cycle. Before you begin this repair, it is recommended that you pull your dishwasher out of the cabinet, so you can tip the dishwasher to one side and gain better access to the circulation pump and motor. Be sure to disconnect the power source and the water source to the dishwasher before you begin this repair. To complete this repair you will need a 1/4 inch nut driver and a 3/8 inch nut driver.
The rubber washer is a part which is specific to dishwashers and should not be substituted by a similar part. It works with the heating element to seal the receptacle opening where the heating element is attached. The rubber washer is used to prevent water leaking from your dishwasher during its cycle. Before making any repairs to your dishwasher make sure that you disconnect the power by finding the breaker for the dishwasher, and turning it off. The tools you will need to complete this repair include an adjustable wrench, and a 1/4 inch nut driver. This specific rubber washer is sold individually.
This part moves water up from the sump collection area and up through the spray arms.
Measures level of soil in the water.
This is a chopper assembly or drain food chopper, and it is designed for your dishwasher. The chopper chops up/minces the food particles in your dishwasher to prevent them from clogging the pump. You may need to replace this part if your dishes are not being cleaned properly, your appliance is particularly noisy, or you are noticing draining problems. The tools you will need to make this repair include a number 20 and a number 15 torque screwdriver, a small flat blade screwdriver, and a pair of needle nose pliers.
This part is a door balance link kit, also sometimes known as door cable or door spring cable kit, that helps support the door as it opens and closes by connecting to the dishwasher door hinges. The kit includes two door balance links and two door balance mounts with wheels, which will replace both the left and right sides. The only tool needed is a 5/16 nut driver. Before removing the existing kit, take note of how the door balance link kit is assembled for a smooth replacement process. It is recommended to check the door springs in case they need to be replaced as well.
250 max Volt, 23.5 MFD.
Includes power cord and all necessary parts needed for complete installation of cord.
This OEM gray Dishwasher Lower Dishrack Wheel Assembly is a plastic kit that allows the rack to slide in and out of the dishwasher easily. If it breaks or becomes damaged. sliding will feel difficult. This can happen due to normal wear and tear, and the part should be replaced if this occurs. Check your model number and user manual to make sure this part is correct. It attaches directly to the dishrack. To repair, open the dishwasher door and pull out the lower dishrack. Next, push the tab from both sides and it should pop out. To install the new wheel assembly, place it on the rack and make sure the caps overlap the wire from the inside before you clip it in place by pushing the wheel. It measures roughly 3x6 inches.
This genuine OEM thermostat is sourced directly from the manufacturer to ensure compatibility with your dishwasher model. The thermostat monitors and regulates the temperature of the dishwasher heating element. It is responsible for ensuring that the water temperature reaches the optimal level for effective cleaning while also helping to prevent overheating and potential damage to the internal components of the dishwasher.
This wire harness is for dishwashers and supplies power to electrical components in the dishwasher.
Introducing the W11035586 CNTRL-ELEC, a genuine OEM part engineered by Whirlpool. This electronic control board is an essential component for your dishwasher, managing critical functions such as washing, draining and drying. Designed for select models of Whirlpool appliances, it offers durability and precision, ensuring optimal performance of your dishwasher. Before installation, remember to unplug your dishwasher and protect your hands with work gloves. Please ensure the part number matches your model before purchase, as parts may exhibit slight variations in size and shape. Keep your dishwasher running smoothly and efficiently with this Whirlpool electronic control board.