Your coupon for will be reflected when you check out!
✖
Your coupon for
✖
Hello!
You're visiting the PartSelect site in U.S.
Would you like to shop on the Canadian site?
Stay on this site
Go to Canadian site
✖
Model Number Locations
1Select Category Type
Select Category Type
2Select Product Type
Select Product Type
3Select {MODEL} Type
Select {MODEL} Type
Sample Model Number Tags
Model numbers can be made up of numbers (1005400, for example) or a combination of letters and numbers (LAT1000AAE). The model number will most likely appear on either a paper sticker or a metal plate. Your appliance's model number tag may look similar to the sample model number tags shown here (model number highlighted in yellow):
Model has been saved to My Models. If you're not signed in, your lists are available on this device and will expire within 30 days.
Model has been saved to My Models.
Experience quality and durability with the LG Air Conditioner Blower Wheel Heat Pump Bearing. This genuine LG product ensures optimal performance of your room air conditioner by allowing the blower wh...
$11.41
In Stock
Order within the next 8 hrs and your part ships today!
Ask our experts a question about this model and we'll get back to you as soon as possible!
1 question answered by our experts.
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
PAUL
August 9, 2023
LG unit not receiving signal from remote.even bought a new remote. Only way can turn on is press the on off button. 817 791 5682
For model number LMN127HVT
Hello Paul, thank you for reaching out. Based on our understanding of the issue, we would suggest you to reset the remote control. You will see a small hole on the bottom right of the remote control. Find a small sharp object, like a pin, and push it into the hole. Every setting and configuration on the remote will disappear and the remote will go back to factory settings. We hope this sorts out your problem!
Was this helpful?
Thank you for voting!
< Prev
1
Next >
✖
Ask a Question
Ask our experts a question on this model and we'll respond as soon as we can.
This repair was on an LG ductless heat pump. After some period of use, the inside unit will get very dirty inside with moisture, dust, and possibly mold. To clean the insides properly, you will likely have to remove the fan blower wheel. To do this, you will have to disassemble the outside covers of the unit. There are videos on YouTube t
... Read morehat will give you some insight, but the different brands are all a little different in the way they are put together. However, it is still fairly straightforward to get access to the blower wheel. I removed the large outside cover (2 or 3 screws) and then loosened the drain tray at the bottom (also 2 or 3 screws). I did not take the drain tray off because it has the drain tube attached at the rear, and it appeared that it could be difficult to get this back together. Instead, I just removed the screws and pulled it down away from the blower wheel. I then loosened the coil assembly covering the top and front of the blower wheel (2 screws). Again, I did not try to remove the coil assembly because it has the refrigerant tubing attached. At this point, you can use a Phillips screwdriver to reach through the blower wheel on the right end and loosen the setscrew in the hub holding the blower wheel to the motor shaft. Once the screw is loosened, you can lift the coil assembly away and pull the blower wheel out to clean it. Unfortunately, while I was cleaning and drying the blower wheel (which was almost completely clogged with crud), I dropped it and it broke. I ordered the new part from this site. The part was on backorder, but after I received it, I used the reverse procedure to install the new blower wheel. The one thing that is a little tricky is that the setscrew in the blower wheel hub tightens down on a flat on the motor shaft, so you will have to be careful to get the two lined up as you push the blower wheel on the shaft because it is difficult to align them after the wheel is on the shaft. At this point, all you have to do is tighten the setscrew on the motor shaft and reassemble the unit NOTE: while you have the blower wheel out, you can get fair access to the housing inside the unit to clean it.
Main problem was removing the cowling from the LG head unit as I had no instructions on how to do it. I had watched the previous technicians that had worked on the unit remove it. Once the cowling is removed all that needs done is remove the 2 mounting screws and unplug the old motor, plug in the new motor and remount it with the 2 screws
... Read more. Then the cowling has to be reinstalled.
