Your coupon for will be reflected when you check out!
✖
Your coupon for
✖
Hello!
You're visiting the PartSelect site in U.S.
Would you like to shop on the Canadian site?
Stay on this site
Go to Canadian site
✖
Model Number Locations
1Select Category Type
Select Category Type
2Select Product Type
Select Product Type
3Select {MODEL} Type
Select {MODEL} Type
Sample Model Number Tags
Model numbers can be made up of numbers (1005400, for example) or a combination of letters and numbers (LAT1000AAE). The model number will most likely appear on either a paper sticker or a metal plate. Your appliance's model number tag may look similar to the sample model number tags shown here (model number highlighted in yellow):
Model has been saved to My Models. If you're not signed in, your lists are available on this device and will expire within 30 days.
Model has been saved to My Models.
This OEM filter measures 2.5 inches deep, 12.5 inches high, 5 inches wide and roughly 1.5 lbs. It is recommended to replace this filter every six months or 300 gallons, whichever comes first. If you n...
$76.95
In Stock
Order now and your part arrives in 2-3 business days!
This is an authentic OEM part sourced directly from the manufacturer. The crisper slide rail for your refrigerator allows the crisper drawer to slide in and out, and supports the drawer as it does so....
$48.24
In Stock
Order now and your part arrives in 2-3 business days!
This part is the replacement water line or tube for your refrigerator. It is made of white plastic and is sold individually. This tube supplies water to the ice maker and water dispenser If your refri...
$29.86
In Stock
Order now and your part arrives in 2-3 business days!
This part is the replacement water line for your refrigerator. It is a long plastic tube, which is 5/16 of an inch in diameter. If your refrigerator is leaking, or if it will not dispense water or ice...
$29.86
In Stock
Order now and your part arrives in 2-3 business days!
This part is the replacement ice tray for your refrigerator. The tray is made of white plastic and is approximately 9 inches in length, and 3 inches in width. It has the capacity for 8 ice cubes. The ...
$14.94
In Stock
Order now and your part arrives in 2-3 business days!
This genuine OEM lever spring exerts tension between the ice maker door plunger and the ice maker itself on your refrigerator. If there is little to no tension holding your ice door seal in place, the...
$14.94
In Stock
Order now and your part arrives in 2-3 business days!
Introducing the LG Lower Door Hinge Assembly, an authentic OEM item engineered by LG. This hinge assembly is designed to seamlessly integrate with certain LG refrigerator models. Crucial to your appli...
$48.24
In Stock
Order now and your part arrives in 2-3 business days!
Detected noise as coming from top freezer department, and tips and part diagram clearly pointed to evaporator fan. You go in through the freezer (you have to empty top half of freezer); removing the side rails holding the ice bin, and then the 4 outer screws (only 2 each side - not the middle ones) holding the 'auger' that turns the bin
... Read more. From there it gets interesting in trying to disconnect the wires. You might consider taking some pictures of the connected wires - perhaps it doesn't matter, but several of them can be hooked up in reverse. After the ice marker is out, remove light and light cover, side rails/mounts that hold hold up ice maker. This leaves a large white cover that pops out (seam at bottom of it has two tabs that you can pop out) holding the fan; and then only a few more wires to disconnect to be able to get at the fan. Mine clearly had a wobble to it confirming the source of the squeak and need to replace. Install was just reverse -- a bit tricky to get some of the wires connected given the tight spaces. Overall, not difficult - but a lot of wires and screws to connect/disconnect. I didn't take any pictures as I disassembled, and found myself having to take some extra time to figure it out as I reassembled. In the end -- a silent and functioning refrigerator Good luck!
To replace the warped tray, I found the service manual (pg. 124 below) which took some interpreting. Removed the lever. Then removed the assembly by two screws that are forward to the unit and go upwards. The insulation, sensor, and sensor cover are simply pulled down and off and the unit separated to removed the tray, and
... Read morethen insert the new tray. Proceed in reverse. Takes only a few minutes.
