LT141 Husqvarna - Instructions
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Wheel bushings were bad
Removed old clip removed rim from tractor, removed grease fitting on rim, took hammer and screw driver knocked out old bushing turned rim over knocked out other bushing. Press in new bushings reinstalled grease fitting slide tire back on tractor, put retaining washers on then locking clip put on dust cover grease at grease fitting. Repeat other side.
Parts Used:
-
Anthony from OLIVEHILL, TN
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Pliers, Screw drivers
22 of 37 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Needed to replace the bent blades on my riding mower.
- Made the mower safe to work on the blades (remove spark plug wires, etc.)
- Raised the mower to get access to the blades, wedged a wood block against the blade.
- Used impact driver with socket to remove bolt holding blade.
- Removed blade, replaced with new, replaced bolt and tightened with impact driver, ..... and you know the rest.
- Raised the mower to get access to the blades, wedged a wood block against the blade.
- Used impact driver with socket to remove bolt holding blade.
- Removed blade, replaced with new, replaced bolt and tightened with impact driver, ..... and you know the rest.
Parts Used:
-
Trace from LISLE, IL
-
Difficulty Level:Very Easy
-
Total Repair Time:15 - 30 mins
16 of 21 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Take the wheel off. Place the key in the slot. Put the wheel back on.
-
Gary from PILESGROVE, NJ
-
Difficulty Level:Very Easy
-
Total Repair Time:Less than 15 mins
5 of 11 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Mower belt fell off was cut by the drive pulley.
Got the proper length and pulley size belt via serial number. Checked the length prior to ordering to assure the length would be correct.
Took mower onto a flat surface where I could get on both sides of the deck. And then placed the belt on the back pulleys first . Then I routed it through the idler pulleys to the power pulley where I turned the pulley with putting finger pressure against the belt as I turned the pulley. And it went on with no problem . It is that simple just be sure to turn the pulley and apply the belt in the same direction at the same time.
Took mower onto a flat surface where I could get on both sides of the deck. And then placed the belt on the back pulleys first . Then I routed it through the idler pulleys to the power pulley where I turned the pulley with putting finger pressure against the belt as I turned the pulley. And it went on with no problem . It is that simple just be sure to turn the pulley and apply the belt in the same direction at the same time.
Parts Used:
-
Steve from DAMASCUS, OR
-
Difficulty Level:Easy
-
Total Repair Time:Less than 15 mins
1 person
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Dryer runs no heat
Disassemble dryer. Replaced element assembly. Re assembled dryer. Unit runs and heats.
Parts Used:
-
Russell from MACON, GA
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
1 of 3 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Front wheels, too much end play
-
Frederick from BINGHAMTON, NY
-
Difficulty Level:Very Easy
-
Total Repair Time:Less than 15 mins
10 of 36 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!