Your coupon for will be reflected when you check out!
✖
Your coupon for
✖
Hello!
You're visiting the PartSelect site in U.S.
Would you like to shop on the Canadian site?
Stay on this site
Go to Canadian site
✖
Model Number Locations
1Select Category Type
Select Category Type
2Select Product Type
Select Product Type
3Select {MODEL} Type
Select {MODEL} Type
Sample Model Number Tags
Model numbers can be made up of numbers (1005400, for example) or a combination of letters and numbers (LAT1000AAE). The model number will most likely appear on either a paper sticker or a metal plate. Your appliance's model number tag may look similar to the sample model number tags shown here (model number highlighted in yellow):
Model has been saved to My Models. If you're not signed in, your lists are available on this device and will expire within 30 days.
Model has been saved to My Models.
This OEM gray Dishwasher Lower Dishrack Wheel Assembly is a plastic kit that allows the rack to slide in and out of the dishwasher easily. If it breaks or becomes damaged. sliding will feel difficult....
$33.57
In Stock
Order within the next 6 hrs and your part ships today!
This part is a door balance link kit, also sometimes known as door cable or door spring cable kit, that helps support the door as it opens and closes by connecting to the dishwasher door hinges. The k...
$27.95
In Stock
Order within the next 6 hrs and your part ships today!
The rack track stop on your dishwasher is designed to stop the dish rack at the appropriate place when opening and closing the rack. If your dishwasher is not cleaning your dishes properly, the rack s...
$10.44
In Stock
Order within the next 6 hrs and your part ships today!
The mounting bracket is sold individually, without screws. This part secures the upper side of the dishwasher to the underside of the counter or cabinet to prevent the dishwasher from moving, shaking,...
$14.65
In Stock
Order within the next 6 hrs and your part ships today!
This drain pump is used in dishwashers to remove water from the dishwasher tub. If the impeller in the dishwasher is damaged or the motor has been shorted out and will not drain, it is possible the bo...
$59.95
In Stock
Order within the next 6 hrs and your part ships today!
This hose clamp is used in a wide variety of household appliances. Most often it is found in washers, dishwashers, refrigerators, freezers, dehumidifiers, garbage disposals, or air conditioners. This ...
$7.95
In Stock
Order within the next 6 hrs and your part ships today!
The heating element is not designed to heat the water that enters it, but is designed to maintain the heat of the water that enters the dishwasher. It is located on the bottom of the dishwasher.
$77.91
In Stock
Order within the next 6 hrs and your part ships today!
This is a seal, but you may also know it as a door gasket and it is for your dishwasher. The seal forms a watertight barrier between the door and the dishwasher tub, deterring water from escaping duri...
$61.30
In Stock
Order within the next 6 hrs and your part ships today!
This water inlet valve should be located behind the lower kickplate panel in either the right or left corner. The attaching solenoids on the valve open and close according to the desired amount of water needed.
$51.43
In Stock
Order within the next 6 hrs and your part ships today!
Questions And Answers for MDB4949SHZ0
Ask our experts a question about this model and we'll get back to you as soon as possible!
20 questions answered by our experts.
Sort by:
< Prev
1
2
3
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Jeannette
January 6, 2024
How to clean silt from around the bottom inside? I s there a filter in this model?
For model number MDB4949SHZ0
Hi Jeannette,
Thank you for your question. The filter or accumulator, part number PS12349211, is located on the floor of the dishwasher under the lower spray arm. We hope this helps!
The cancel light is coming on, we push 3 seconds to stop it which may work temporarily but the comes back on. I tried to run a wash cycle but it would not start to fill so we pushed cancel button. We have unplugged the unit for now. Any idea's of what can be causing this?
For model number MDB4949SHZ0
Hello Nancy, Thank you for the question. We suggest trying to reset the controls using the control reset command. Turn the dishwasher off. Choose any 3 buttons on the control pad. Press them in the following sequence, 1-2-3-1-2-3-1-2-3 with no more than 1 second between each button push. Now press cancel and that will reset the controls. We hope this helps, good luck with this repair!
1 person found this helpful.
Was this helpful?
Thank you for voting!
Murray
February 21, 2023
DW sometimes doesn’t complete cycle. I have replaced door switch. Sometimes stops in drying stage. Other times leaves water in machine. 4 years old. Thanks.
For model number MDB4949SHZ0
Hello Murray, thank you for reaching out. According to our research, the electronic control board, part number PS12583931, manages the functions such as washing, draining, and drying. The turbidity sensor, part number PS12070543, determines the turbidity of the wash water. The control board communicates with the turbidity sensor and decides how long to wash in all the cycles. We suggest you check these parts. We hope this solves your problem!
Found loose L-shaped spring, believe it is part of detergent dispenser sliding door, but don’t see it on any parts list or obvious place it would snap in. Doesn’t appear broken, just loose? Reversed pins on each end.
For model number MDB4949SHZ0
Hello Peter, thank you for reaching out to PartSelect. If the spring is loose, then the detergent dispenser, part number PS11731570 will need to be replaced because the spring does not come separately. Good luck with this repair!
Pulled dishwasher from under counter, attached link to spring, hooked spring back into frame/chassis, threaded link through pulleys, attached other end of link onto door, reinstalled dishwasher under counter. All's well. Note-I purchased an extra link anticipating that the other one will fail. They're cheap enough.
Caviat: The actual repair is less than 15 minutes, but I spent a lot of time playing with it before I figured out it was that easy and fast. You don't need to remove the dishwasher from the counter to do this. And it will probably help to look at the new part closely so you can understand where the retainer clip is to press it and release
... Read more the old pump.
First remove the water from the dishwasher pan that would not drain with a wet/dry vac. Otherwise the water will all drain on the floor when you remove the pump. Then remove the two screws on the kickplate on the front of the unit below the door. Remove the kickplate/maintainence access cover. The drain pump is on the right about 8 inches in. Using two hands you grasp the drain pump with your right hand and use the left hand to push the retaining clip down. Then the drain pump will rotate 1/4 turn counterclockwise and can be removed without pulling the dishwasher out. There is likely to be some water leak out that was traped in the pump housing that you can not reach with the vac. Disconnect the wire. Connect the wire to the new pump, put it in place and 1/4 turn clockwise to install it. Replace the kickplate and you're done.
1. Open the dishwasher and remove the two plastic grommets about halfway down on either side of the opening. Then remove the two screws under the grommets.
2. Remove the kick plate under the door. May have to lower unit by turning the feet using the adjustable wrench.
3. Make sure you have enough slack in the water i
... Read morenput line and electrical wiring that you can pull the dishwasher out about 12 inches or more.
4. There is a spring and nylon rope link on both sides of the unit. Probably just one link is broken, but the replacement comes with two, so you can replace both or save one as a spare. Look at the good side and it should be pretty self explanatory how it attaches. I found it easiest to first thread the link around the lower pulley, then attach the link to the spring, then spring to the rear support, then the link to the door.
